View MT9072_257086.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MT9072
Octal T1/E1/J1 Framer Data Sheet
Features
* * * * Eight fully independent, T1/E1/J1 framers 3.3V supply with 5V tolerant inputs Selectable 2.048 Mbit/s or 8.192 Mbit/s serial buses for both data and signaling Framing Modes: - T1: D4, ESF, T1DM - E1: Basic Framing, CRC4 multiframing and Signaling Multiframing Supports Inverse Mux for ATM Timeslot assignable HDLC IEEE-1149.1 (JTAG) test port T1/E1/J1 add/drop multiplexers V5.1 and V5.2 access network interfaces CO and PBX equipment interfaces Primary rate IDSN nodes Digital Cross-connect Systems (DCS) Wireless base stations
DS5063 Issue 4 September 2002
Ordering Information MT9072AB208 Pin LQFP MT9072AV220 Pin LBGA -40 to +85 0C
* * * * * * * * *
Description
The MT9072 is a multi-port T1/E1/J1 framing device that integrates eight fully independent, feature rich framers. The device is software selectable between T1, E1 or J1 modes and meets the latest relevant recommendations and standards from Telcordia, ANSI, ETSI and ITU-T. An extensive suite of features make the MT9072 very flexible and suitable for a wide variety of applications around the globe.
Applications
TxDL[0] TxDLC[0] DSTi [0] CSTi [0]
TxCL [0] Transmit Framing, Error and TPOS[0] TNEG[0]
ST-BUS Interface ST-BUS Loopback Payload Loopback
Test Signal Generation
CKi[0] FPi[0]
National Bit Buffer CAS Buffer
Remote Loopback
ST-BUS Data Link
Circuit Timing
Digital Loopback
RPOS[0] RNEG[0]
DSTo[0] CSTo[0]
ST-BUS Interface
Receive Framing, Performance Monitoring, Alarm Detection, 2 Frame Slip Buffer
RxBF[0] EXCLi[0]
FRAMER 0 FRAMER 1 FRAMER 2 FRAMER 3 FRAMER 4 FRAMER 5 FRAMER 6 FRAMER 7
RxDLC[0] RxDL[0] RxMF[0]
Microprocessor Interface
IEEE 1149.1 TAP
Common Control and Power
D15~D0 A11~A0
DS RW CS
IRQ IM
TDI TDO TMS TCK TRST RESET TAIS VDDVSS T1-3
TxMF
Figure 1 - Block Diagram
SEMICMF.019
1
MT9072
MT9072 Detailed Feature Summary
Standards Compliance and Support T1/J1 Mode ANSI: T1.102, T1.231 T1.403, T1.408 AT&T: TR 62411, PUB43801 Telcordia: GR-303-CORE ITU-T: G.802 TTC: JT-G703, JT-G704 JT-G706 ITU-T: ETSI: TBR4, TBR13 ETS 300 233, ETS 300 347 (V5.2) E1 Mode
Data Sheet
G.703, G.704, G.706, G.711, G.732 G.775, G.796, G.823, I.431 G.965 (V5.2)
Access and Control * A 16-bit parallel Motorola or Intel non-multiplexed microprocessor interface is used to access the control and status registers. Backplane Interfaces * 2.048Mbit/s or 8.192Mbit/s ST-BUS * 2.048Mbit/s GCI bus * IMA (Inverse Mux for ATM) mode, 1.544Mbit/s (T1) or 2.048Mbit/s (E1) serial bus with asynchronous transmit and receive timing for Inverse MUX for ATM applications. * CSTo/CSTi pins can be used to access the receive/transmit signaling data * RxDL pin can be used to access the entire B8ZS/HDB3 decoded receive stream including framing bits * TxDL pin can be used to transmit data on the FDL (T1) or the Sa bits (E1)
T1/J1 Mode * * PCM24 channels 1-24 are mapped to ST-BUS channels 0-23 respectively The framing-bit is mapped to ST-BUS channel 31 *
E1 Mode PCM30 timeslots 0-31 are mapped to ST-BUS channels 0-31 respectively
2
SEMICMF.019
Data Sheet
Data Link T1/J1 Mode * Three methods are provided to access the datalink: 1. TxDL and RxDL pins support transmit and receive datalinks 2. Bit Oriented Messages are supported via internal registers 3. An internal HDLC can be assigned to transmit/receive over the FDL in ESF mode * * E1 Mode
MT9072
Two methods are provided to access the datalink: 1. TxDL and RxDL pins support transmit and receive datalinks over the Sa4~Sa8 bits 2. An internal HDLC can be assigned to transmit/receive data via the Sa4~Sa8 bits In transparent mode, if the Sa4 bit is used for an intermediate datalink, the CRC-4 remainder can be updated to reflect changes to the Sa4 bit
One Embedded Floating HDLC per Framer * * * * Flag generation and Frame Check Sequence (FCS) generation and detection, zero insertion and deletion Continuous flags, or continuous 1s are transmitted between frames Transmit frame-abort Invalid frame handling: Frames yielding an incorrect FCS are tagged as bad packets Frames with fewer than 25 bits are ignored Frames with fewer than 32 bits between flags are tagged as bad packets Frames interrupted by a Frame-Abort sequence remain in the FIFO and an interrupt is generated * * * * * * * * * * * Access is provided to the receive FCS FCS generation can be inhibited for terminal adaptation Recognizes single byte, dual byte and all call addresses Independent, 32 byte deep transmit and receive FIFOs Receive FIFO maskable interrupts for nearly full and overflow conditions Transmit FIFO maskable interrupts for nearly empty and underflow conditions Maskable interrupts for transmit end-of-packet and receive end-of-packet Maskable interrupts for receive bad-frame (includes frame abort) Transmit-to-receive and receive-to-transmit loopbacks are provided Transmit and receive bit rates and enables are independent Frame aborts can be sent under software control and they are automatically transmitted in the event of a transmit FIFO underrun
T1/J1 Mode * * Assignable to the ESF Facility Data Link or any other channel Operates at 4 kbit/s (FDL), 56 kbit/s or 64 kbit/s * *
E1 Mode Assignable to timeslot-0, bits Sa4~Sa8 or any other timeslot Operates at 4, 8, 12, 16 or 20 kbit/s (Sa bits) or 64 kbit/s
SEMICMF.019
3
MT9072
Data Sheet
Common Channel Signaling Timeslot Assigner * Selected 64 Kbit/s CCS channels (for V5.2 and GR-303) can be routed to/from an external multichannel HDLC, using the CSTi/0 pins Access and Monitoring for National (Sa) Bits (E1 mode only) In addition to the datalink functions, the Sa bits can be accessed using: *Single byte register *Five byte transmit and receive national bit buffers *A maskable interrupt is generated on the change of state of any Sa bit Slip Buffers T1/J1 Mode Transmit Slip Buffer * Two-frame slip buffer capable of performing a controlled slip. Intended for rate conversion in the transmit direction * * * * Programmable delay Transmit slips are independent of receive slips Indication of slip Indication of slip direction E1 Mode Receive Slip Buffer * Two-frame slip buffer capable of performing a controlled slip * Wander tolerance of 208 UI peak-to-peak * * Indication of slip Indication of slip direction
Receive Slip Buffer * Two-frame slip buffer capable of performing a controlled slip * * * Wander tolerance of 142 UI (92 s) peak Indication of slip Indication of slip direction
Interface to the Physical Layer Device * * * Single rail NRZ Dual rail (AMI) RZ or NRZ Transmits/samples data on the rising or falling edge of the line clock T1/J1 Mode * * * * * * Optional B8ZS line coding Pulse density enforcement Forced ones stuffing (bit 7 of a DS0) GTE zero suppression code Bell zero suppression code DDS zero suppression code * E1 Mode Optional HDB3 line coding
4
SEMICMF.019
Data Sheet
Framing Algorithm T1/J1 Mode * * Synchronizes with D4 or ESF protocols Supports T1DM synchronization with the D4 pattern and timeslot 24 T1DM Sychronization bytes Framing circuit is off-line Transparent transmit and receive mode In D4 mode Fs bits can be optionally cross checked with the Ft bits The start of the ESF multiframe can be determined by the following methods: Free-run Software reset Synchronized to the incoming multiframe * An automatic reframe is initiated if the framing bit error density exceeds the programmed threshold In transparent mode no reframing is forced by the device Software can force a reframe at any time In ESF mode the CRC-6 bits can be optionally confirmed before forcing a new frame alignment During a reframe the signaling bits are frozen, and error counting for Ft, Fs, ESF framing pattern and CRC-6 bits is suspended If J1 CRC-6 is selected the Fs bits are included in the CRC-6 calculation J1-CRC-6 and J1-Yellow Alarm can be independently selected Supports Robbed Bit Signaling Optional forced ones insertion * * * * * * * * E1 Mode
MT9072
Three distinct and independent E1 framing algorithms 1. Basic frame alignment 2. Signaling multiframe alignment 3. CRC-4 multiframe alignment
* * * *
* * *
*
* * *
*
Transparent receive mode Transparent transmit mode Optional automatic interworking between interfaces with and without CRC-4 processing capabilities is supported An automatic reframe is forced if 3 consecutive frame alignment patterns or three consecutive non-frame alignment bits are received in error In receive transparent mode no reframing is forced by the device Software can force a reframe at any time Software can force a multiframe reframe at any time E-bits can optionally be set to zero or one until CRC synchronization is achieved Optional automatic RAI Supports CAS multiframing Optional automatic Y-bit to indicate CAS multiframe alignment
* * * *
Channel Associated Signaling * * * * * * ABCD or AB bits can be automatically inserted and extracted Transmit ABCD or AB bits can be passed via the microport or via the CSTi pin Receive ABCD or AB bits are accessible via the microport or via the CSTo pin Unused nibble positions in the CSTi/CSTo bandwidth are tri-stated An interrupt is provided in the event of changes in any of the signaling bits Receive signaling bits are frozen if digital loss of signal or loss of multiframe alignment is declared T1/J1 Mode * * * Signaling bits can be debounced by 6 ms Robbed bit or clear channel signaling are selected on a channel by channel basis Signaling interrupts period can be selected: 1, 4 or 8 msec * * E1 Mode Signaling bits can be debounced by 14 ms Signaling interupt period can be selected 1, 4 or 8 msec
SEMICMF.019
5
MT9072
Alarms T1/J1 Mode Yellow Alarm D4 mode, two types: 1. Bit position 2 is zero for virtually every DS0 over 48ms 2. Two consecutive ones in the S-bit position of the twelfth frame ESF mode, two types: 3. Reception of 0000000011111111 in eight or more codewords out of ten (T1) 4. Reception of 1111111111111111 in eight or more codewords out of ten (J1) T1DM mode : Bit 2 of the T1DM synchronization byte is 0 Alarm Indication Signal (AIS) Declared if fewer than six zeros are detected during a 3 ms interval Loss Of Signal (LOS) * Loss Of Signal is declared if 192 or 32 consecutive zeros are received * E1 Mode Remote Alarm Indication (RAI) * Bit 3 of the receive NFAS
Data Sheet
Alarm Indication Signal (AIS) * Unframed all ones signal for at least a double frame or two double frames Timeslot 16 Alarm Indication Signal * All ones signal in timeslot 16 Loss Of Signal (LOS) * Loss Of Signal is declared if 192 or 32 consecutive zeros are received
Remote Signaling Multiframe Alarm * Y-bit of the multiframe alignment signal
6
SEMICMF.019
Data Sheet
Performance Monitoring Error Counters * * * * All counters can be cleared or preset by writing to the appropriate locations Maskable occurrence interrupt Maskable overflow interrupt Counters can be latched on one second intervals T1/J1 Mode * * * * * * * * * CRC-6 Multiframe Counter (8-bit) PRBS Error Counter (8-bit) Multiframes Out of Sync Counter (16-bit) Framing Bit Error Counter (16-bit) Bipolar Violation Counter (16-bit) CRC-6 Error Counter (16-bit) Out of Frame Alignment Counter (8-bit) Change of Frame Alignment Counter (8-bit) Excessive Zeros Counter (8-bit) * * * * * * * * E1 Mode CRC-4 Multiframe Counter (8-bit) PRBS Error Counter (8-bit) Loss of Basic Frame Sync (16-bit) E-bit Error Counter (16-bit) Bipolar Violation Counter (16-bit) CRC-4 Error Counter (16-bit) FAS Bit Error Counter (8-bit) FAS Error Counter (8-bit)
MT9072
Error Insertion T1/J1 Mode * * * * * * Bipolar Violations CRC-6 errors Ft errors Fs errors Payload errors Loss of Signal error * * * * * * * E1 Mode E-bit Bipolar Violations CRC-4 Errors FAS Errors NFAS Errors Payload Errors Loss of Signal Error
Loopbacks * Digital loopback * Remote loopback * ST-BUS loopback * Payload loopback * Local timeslot loopback * Remote timeslot loopback * Framer to framer loopback Per Timeslot Control The following features can be controlled on a per timeslot basis: * * * * * * * * Clear Channel Capability (only used in T1/J1) Choice of sourcing transmit signaling bits from microport or CSTi pin Remote timeslot loopback Local timeslot loopback PRBS insertion and reception Digital milliwatt pattern insertion Per channel inversion for transmit and receive Transmit and receive idle code
SEMICMF.019
7
MT9072
Data Sheet
CSTi[7] DSTo[7] DSTi[7] RxMF[7] TxDLC[7] TxDL[7] RxDLC[7] RxDL[7] TxCL[7] TNEG[7] TPOS[7] ExCLi[7] RNEG[7] RPOS[7] VDD VSS RxBF[6] FPi[6] CKi[6] CSTo[6] CSTi[6] TxDL[6] DSTi[6] RxMF[6] TxCL[6] TxDLC[6] DSTo[6] RxDLC[6] RxDL[6] TNEG[6] TPOS[6] ExCLi[6] RNEG[6] RPOS[6] VDD VSS RxBF[5] FPi[5] CKi[5] CSTo[5] CSTi[5] DSTo[5] DSTi[5] RxMF[5] TxDLC[5] TxDL[5] RxDLC[5] RxDL[5] TxCL[5] TNEG[5] TPOS[5] ExCLi5] 156 154 152 150 148 146 144 142 140 138 136 134 132 130 128 126 124 122 120 118 116 114 112 110 108 106 158 160 162 164 166 168 92 170 172 174 176 84 178 180 80 182 184 186 188 72 190 192 194 66 196 64 198 62 200 202 58 204 206 54 208 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 56 60 70 68 78 76 74 82 90 88 86 104 102 100 98 96 94
CSTo[7] CKi[7] FPi[7] RxBF[7] VSS VDD D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 VSS VDD A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 CS DS R/W IRQ I/M RESET TAIS TxMF T3 T1 T2 TDI TDO TMS TCK TRST
208 PIN LQFP
RNEG[5] RPOS[5] VDD VSS RxBF[4] FPi[4] CKi[4] CSTo[4] CSTi[4] DSTo[4] DSTi[4] RxMF[4] TxDLC[4] TxDL[4] RxDLC[4] RxDL[4] TxCL[4] TNEG[4] TPOS[4] ExCLi[4] RNEG[4] RPOS[4] VDD VSS RxBF[3] FPi[3] CKi[3] CSTo[3] CSTi[3] DSTo[3] DSTi[3] RxMF[3] TxDLC[3] TxDL[3] RxDLC[3] RxDL[3] TxCL[3] TNEG[3] TPOS[3] ExCLii[3] RNEG[3] RPOS[3] VDD VSS RxBF[2] FPi[2] CKi[2] CSTo[2] CSTi[2] DSTo[2] DSTi[2] RxMF[2]
8
VSS VDD RPOS[0] RNEG[0] ExCLi[0] TPOS[0] TNEG[0] TxCL[0] RxDL[0] RxDLC[0] TxDL[0] TxDLC[0] RxMF[0] DSTi[0] DSTo[0] CSTi[0] CSTO[[0] CKi[0] FPi[0] RxBF[0] VSS VDD RPOS[1] RNEG[1] ExCLi[1] TPOS[1] TNEG[1] TxCL[1] RxDL[1] RxDLC[1] TxDL[1] TxDLC[1] RxMF[1] DSTi[1] DSTo[1] CSTi[1] CSTo[1] CKi[1] FPi[1] RxBF[1] VSS VDD RPOS[2] RNEG[2] E2i[2] TPOS[2] TNEG[2] TxCL[2] RxDL[2] RxDLC[2] TxDL[2] TxDLC[2]
Figure 2 - Pin Connections (Jedec MS-026)
SEMICMF.019
Data Sheet
MT9072
2
205 TDO
1 A B C D E F G H J K L M N P R T
NC
3
204 TDI 206 TMS 208 TRST
4
201 T3 202 T1 203 T2 6
5
199 TAIS 200 TXMF 198 RESET 197 IM NC
6
193 CS 195 RW 196 IRQ 194 DS NC
7
192 A11 190 A9 191 A10 189 A8 101 VSS
8
187 A6 185 A4 186 A5 188 A7 121 VSS
9
182 A1 181 A0 183 A2 184 A3 141 VSS
10
178 D15 177 D14 175 D12 176 D13 161 VSS
11
171 D8 172 D9 173 D10 174 D11 179 VSS
12
168 D5 167 D4 169 D6 170 D7 NC
13
163 D0 157 CSTO[7] 153
14
164 D1 158 CKI[7] 154
15
165 D2 159 FPI[7] 155 DSTo[7] 151
16
166 D3 160 RXBF[7] 156 CSTI[7] 152
209 IDDq NC
207 TCK NC
RXMF[7] DSTI[7] 149 150
3
4
5
RPOS[0] RNEG[0] EXCLi[0] TPOS[0] 7 8 9 10
RXDL[7] RXDLC[7] TXDL[7] TXDLC[7] 145 146 147 148
TNEG[0] TXCL[0] RXDL[0] RXDLC[0] 11 12 13 14 NC
EXCLi[7] TPOS[7] TNEG[7] TXCL[7] NC 139 FPI[6] 140 143 144
TXDL[0] TXDLC[0] RXMF[0] DSTI[0] 15 DSTo[0] 19 FPi[0] 25 16 17 18 CKI[0] 24 2 VDD 22 VDD 42 VDD 62 VDD 82 VDD NC NC 1 VSS 59 60 63 21 VSS 64 41 VSS 77 61 VSS 78 CKI[3] 84 81 VSS 79 FPI[3] 85 80 102
RXBF[6] RPOS[7] RNEG[7] 136 137 138 CKI[6] 134
130 DSTo[6] 135
CSTI[0] CSTO[0] 20 23
RXBF[0] RPOS[1] RNEG[1] 26 27 28
Top View
VDD 122 VDD 142 VDD 162 VDD 180 VDD NC
CSTI[6] CSTO[6] 131 133
TXDL6] TXDLC[6] RXMF[6] DSTI[6] 127 132 128 129
EXCLi[1] TPOS[1] TNEG[1] TXCL[1] 29 30 31 32
TNEG[6] TXCL6] RXDL[6] RXDLC[6] 123 124 125 126
RXDL[1] RXDLC[1] TXDL[1] TXDLC[1] 33 34 35 DSTo[1] 39 FPi[1] 45 36 CSTI[1] 40 RXBF[1] 46
RPOS6] RNEGI6] EXCLi[6] TPOS[6] 117 CSTO[5] 113 118 CKI5] 114 119 FPI[5] 115 DSTo[5] 111 120 RXBF[5] 116 CSTI[5] 112
RXMF[1] DSTI[1] 37 CSTOI1] 43 38 CKI[1] 44
RXMF[5] DSTI[5] 109 110
RPOS[2] RNEG[2] EXCLi[2] TPOS[2] 47 48 49 50
FPI[2] RXBF[2] RPOS[3] RNEG[3] CSTO[3] 65 66 67 68 83
RXBF[3] RXDL[5] RXDLC[5] TXDL[5] TXDLC[5] 86 105 106 107 108
TNEG[2] TXCL[2] RXDL[2] RXDLC[2] 51 52 53 54
EXCLi[3]TPOS[3] TNEG[3] TXCL[3] RPOS[4] RNEG[4] EXCLi[4] TPOS[4] EXCLi[5] TPOS[5] TNEG[5] TXCL[5] 69 70 71 72 87 88 89 90 99 100 103 104
TXDL[2] TXDLC[2] RXMF[2] DSTI[2] 55 DSTo[2] 56 57 58 CKI[2]
RXDL[3] RXDLC[3] TXDL[3] TXDLC[3] TNEG[4] TXCL[4] RXDL[4] RXDLC[4] FPi[4] 73 74 75 76 91 92 93 94 95
RXBF[4] RPOS[5] RNEG[5] 96 97 98 CKI[4]
CSTI[2] CSTO[2]
RXMF[3] DSTI[3] DSTo[3] CSTI[3] TXDL[4] TXDLC[4] RXMF[ 4] DSTI[4] DSTo[4] CSTI[4] CSTO[4]
Figure 3 - 220 PIN LBGA (Jedec MO-192)
Note: The pin numbers inside the balls for the LBGA package correspond to the pin numbers on the device in the Pin Description Table.
SEMICMF.019
9
MT9072
Pin Description
Pin # LQFP 1,21,41,61, 81,101,121, 141,161, 179 LBGA E7,E8,E9, E10,E11, M7,M8,M9, M10,M11 Name VSS Type P Ground. 0VDC. Description (see Notes 1 to 7)
Data Sheet
2,22,42,62, G5,H5,J5, 82,102,122, K5,L5,G12, 142,162,18 H12J12,K1 0 2,L12 3 23 43 63 83 103 123 143 D1 H3 N1 N7 P9 R15 K13 F15
VDD
P
Supply Voltage. +3.3VDC nominal.
RPOS[0] RPOS[1] RPOS[2] RPOS[3] RPOS[4] RPOS[5] RPOS[6] RPOS[7]
I
Receive Positive. This pin is an input for the receive side of the framer; it typically interfaces to an LIU. If used by itself it can accept single rail NRZ (Non Return to Zero) data. If RPOS is used in conjunction with RNEG it can accept dual rail NRZ data or dual rail RZ (Return to Zero) data. The clock at the EXCLi pin is used to clock data into the RPOS pin. Pins RPOS[0-7] are used for Framers[0-7] respectively. In T1 mode, transmit line codes are selected with control bits: RZCS10, RXB8ZS, RZNRZ and UNIBI (Address Y01). T1 mode is selected if the T1E0 bit (Address 900) is 1. In E1 mode, line codes are selected with control bits: COD0-1 and RHDB3 at (Address Y02). E1 mode is selected if the T1E0 bit (Address 900) is 0.
4 24 44 64 84 104 124 144
D2 H4 N2 N8 P10 R16 K14 F16
RNEG[0] RNEG[1] RNEG[2] RNEG[3] RNEG[4] RNEG[5] RNEG[6] RNEG[7]
I
Receive Negative. This pin is an input for the receive side of the framer; it typically interfaces to an LIU. RNEG is used in conjunction with RPOS to accept dual rail NRZ (Non Return to Zero) data or dual rail RZ (Return to Zero) data. The clock at the EXCLi pin is used to clock data into the RNEG pin. Pins RNEG[0-7] are used for Framers[0-7] respectively. In T1 mode, receive line codes are selected with control bits: RZCS10, RXB8ZS, RZNRZ and UNIBI at (Address Y01). T1 mode is selected if the T1E0 bit (Address 900) is 1. In E1 mode, line codes are selected with control bits: COD0-1 and RHDB3 at (Address Y02). E1 mode is selected if the T1E0 bit (Address 900) is 0.
5 25 45 65 85 105 125 145
D3 J1 N3 P5 P11 P13 K15 E13
EXCLi(0) EXCLi(1) EXCLi(2) EXCLi(3) EXCLi(4) EXCLi(5) EXCLi(6) EXCLi(7)
I
1.544/2.048 MHz Extracted Clock. The rising edge of the clock applied at this input is used to clock RZ data into the receive side of the framer on pins RPOS and RNEG. If RPOS/RNEG are configured for NRZ input then either a rising or falling edge on the EXCLi clock can be selected to clock RPOS/RNEG data. Pins EXCLi[0-7] are used for Framers[0-7] respectively. In T1 mode, this pin accepts a 1.544MHz extracted clock. An active rising or falling edge is selected with the CLKE bit (Address Y01). See Figure 53. In E1 mode, this pin accepts a 2.048MHz extracted clock. An active rising or falling edge is selected with the CLKE bit (Address Y02). See Figure 73.
10
SEMICMF.019
Data Sheet
Pin Description (continued)
Pin # LQFP 6 26 46 66 86 106 126 146 LBGA D4 J2 N4 P6 P12 P14 K16 E14 Name TPOS[0] TPOS[1] TPOS[2] TPOS[3] TPOS[4] TPOS[5] TPOS[6] TPOS[7] Type O Description (see Notes 1 to 7)
MT9072
Transmit Positive. This pin is an output for the transmit side of the framer; it typically interfaces to an LIU. If used by itself it can provide single rail NRZ (Non Return to Zero) data. If TPOS is used in conjunction with TNEG it can provide dual rail NRZ data or dual rail RZ (Return to Zero) data. The clock at the TXCL pin is used to clock data out of the TPOS pin. Pins TPOS[0-7] are used for Framers[0-7] respectively. In T1 mode, line codes are selected with control bits: TZCS2-0, TPDV, TXB8ZS, RZNRZ and UNIBI (Address Y01). T1 mode is selected if the T1E0 bit (Address 900) is 1. In E1 mode, line codes are selected with control bits: COD0-1 and THDB3 (Address Y02). E1 mode is selected if the T1E0 bit (Address 900) is 0.
7 27 47 67 87 107 127 147
E1 J3 P1 P7 R9 P15 J13 E15
TNEG[0] TNEG[1] TNEG[2] TNEG[3] TNEG[4] TNEG[5] TNEG[6] TNEG[7]
O
Transmit Negative. This pin is an output for the transmit side of the framer; it typically interfaces to an LIU. TNEG is used in conjunction with TPOS to provide dual rail NRZ (Non Return to Zero) data or dual rail RZ (Return to Zero) data. The clock at the TXCL pin is used to clock data out of the TNEG pin. Pins TNEG[0-7] are used for Framers[0-7] respectively. In T1 mode, line codes are selected with control bits: TZCS2-0, TPDV, TXB8ZS, RZNRZ and UNIBI (Address Y01). T1 mode is selected if the T1E0 bit (Address 900) is 1. In E1 mode, line codes are selected with control bits: COD0-1 and THDB3 (Address Y02). E1 mode is selected if the T1E0 bit (Address 900) is 0.
8 28 48 68 88 108 132 148
E2 J4 P2 P8 R10 P16 J14 E16
TXCL[0] TXCL[1] TXCL[2] TXCL[3] TXCL[4] TXCL[5] TXCL[6] TXCL[7]
IO
1.544/2.048 MHz Transmit Clock. This pin accepts/outputs a clock that is used to clock data out of the transmit side of the framer on pins TPOS and TNEG. If TPOS/TNEG are configured for RZ output then the rising edge of the clock is used to clock TPOS/TNEG data. If TPOS/TNEG are configured for NRZ output then either a rising or falling TxCL edge can be selected to clock TPOS/TNEG data. Pins TxCL[0-7] are used for Framers[0-7] respectively. In T1 mode this pin is an input. The 1.544MHz transmit clock is typically provided by an external PLL (Phase Lock Loop) or LIU. An active rising or falling edge is selected with the CLKE bit (Address Y01). See Figure 52. In E1 mode this pin is an output. The 2.048MHz transmit clock is synchronous with the 4.096MHz ST-BUS clock input to pin CKi. An active rising or falling edge is selected with the T2OP bit (Address Y02). See Figure 71.
SEMICMF.019
11
MT9072
Pin Description (continued)
Pin # LQFP 9 29 49 69 89 109 128 149 LBGA E3 K1 P3 R5 R11 N13 J15 D13 Name RxDL[0] RxDL[1] RxDL[2] RxDL[3] RxDL[4] RxDL[5] RxDL[6] RxDL[7] Type O Description (see Notes 1 to 7)
Data Sheet
Receive Data Link. The entire received data stream including framing bits, after B8ZS/HDB3 decoding, is clocked out of the RxDL pin by the clock at the EXCLi pin. RxDL data does not pass through the receive slip buffer. The embedded data link is flagged by RxDLC. Pins RxDL[0-7] are used for Framers[0-7] respectively. In T1 mode this is a 1.544Mbit/s data stream clocked out with the rising edge of the clock at the EXCLi pin. In E1 mode this is a 2.048 Mbit/s data stream clocked out with the falling edge of the clock at the EXCLi pin.
10 30 50 70 90 110 129 150
E4 K2 P4 R6 R12 N14 J16 D14
RxDLC[0] RxDLC[1] RxDLC[2] RxDLC[3] RxDLC[4] RxDLC[5] RxDLC[6] RxDLC[7]
O
Receive Data Link Clock. This pin outputs a clock that can be used to clock selected bits from the RxDL data stream into an external device. The RxDLC pin can also be configured as an enable signal. Pins RxDLC[0-7] are used for Framers[0-7] respectively. In T1 mode the FDL (Facility Data Link) bits embedded in the RxDL data stream can be clocked into an external device with the rising edge of this 4kHz clock. The rising edge of the clock is centered on the S-bit position and it is coincident with the falling edge of the clock provided to the EXCLi pin. The RxDLC pin can be configured as a clock or an enable signal with the DLCK bit (Address Y06). See Figure 49. In T1 IMA (Inverse Mux for ATM) mode the RxDLC pin outputs the same 1.544MHz clock that is input to the EXCLi pin. In IMA mode the DSTo data stream will be synchronous with this 1.544MHz clock. IMA mode is selected by setting the IMA bit (Address Y00) to 1. See Figure 39. In E1 mode the selected data link national bits (timeslot 0, bits 4-8 of the NFAS (Non-Frame Alignment Signal) frames) can be clocked into an external device with the rising edge of this clock. The Receive Data Link clock is a gapped 4, 8, 12, 16 or 20 kHz, clock as programmed by the Datalink Control Register (Address Y08), derived by gating the 2.048MHz clock provided to the EXCLi pin. The RxDLC pin can be configured as a clock or an enable signal with the DLCK bit (Address Y08). See Figure 68. In E1 IMA (Inverse Mux for ATM) mode the RxDLC pin provides an ST-BUS type 4.096MHz clock derived by doubling the 2.048MHz clock provided to the EXCLi pin. In IMA mode the DSTo data stream will be synchronous with this 4.096MHz clock. IMA mode is selected by setting the IMA bit (Address Y00) to 1. See Figure 58.
12
SEMICMF.019
Data Sheet
Pin Description (continued)
Pin # LQFP 11 31 51 71 91 111 135 151 LBGA F1 K3 R1 R7 T9 N15 H13 D15 Name TxDL[0] TxDL[1] TxDL[2] TxDL[3] TxDL[4] TxDL[5] TxDL[6] TxDL[7] Type I Description (see Notes 1 to 7)
MT9072
Transmit Data Link. This pin accepts data from an external device for the Transmit Data Link. Pins TxDL[0-7] are used for Framers[0-7] respectively. In T1 mode this pin accepts a 4kbit/s serial input stream that contains the ESF FDL (Facility Data Link) bits that are to be embedded in the transmit data stream. The data is clocked in by the rising edge of the clock provided at the TxDLC pin. TxDL data does not pass through the transmit slip buffer. In E1 mode this pin accepts a 4,8,12,16 or 20 kbit/s, as programmed by the Datalink Control Register (Address Y08), data stream which contains the data link national bits (timeslot 0, bits 4-8 of the NFAS (Non-Frame Alignment Signal) frames) for transmission. The selected data link national bits are clocked into the framer by the falling edge of the clock provided at the TxDLC pin.
12 32 52 72 92 112 131 152
F2 K4 R2 R8 T10 N16 H14 D16
TxDLC[0] TxDLC[1] TxDLC[2] TxDLC[3] TxDLC[4] TxDLC[5] TxDLC[6] TxDLC[7]
O
Transmit Data Link Clock. This pin provides a clock that is used to clock transmit data link data out of an external device into the TxDL pin. The TxDLC pin can also be configured as an enable signal. Pins TxDLC[0-7] are used for Framers[0-7] respectively. In T1 mode, this pin provides either a 4kHz clock derived by gating the 1.544MHz clock provided to the TxCL pin, or it provides an enable signal. The TxDLC pin can be configured as a clock or an enable signal with the DLCK bit (Address Y06). Transmit data link data does not pass through the transmit slip buffer. See Figure 47. In E1 mode, this pin provides either a gapped 4,8,12,16 or 20 kHz clock, as programmed by the Datalink Control Register (Address Y08), derived by gating the 2.048MHz clock provided to the TxCL pin, or it provides an enable signal. The TxDLC pin can be configured as a clock or an enable signal with the DLCK bit (Address Y08). See Figure 66.
SEMICMF.019
13
MT9072
Pin Description (continued)
Pin # LQFP 13 33 53 73 93 113 133 153 LBGA F3 L1 R3 T5 T11 M13 H15 C13 Name RxMF[0] RxMF[1] RxMF[2] RxMF[3] RxMF[4] RxMF[5] RxMF[6] RxMF[7] Type O Description (see Notes 1 to 7)
Data Sheet
Receive Multiframe Boundary. This pin provides a pulse that identifies basic frame 0 (the start of bit cell 7 of channel 0) of each received multiframe on the ST-BUS data stream (DSTo). The RxMF pin operates the same way in 2.048Mbit/s and 8.196Mbit/s modes. Pins RxMF[0-7] are used for Framers[0-7] respectively. In T1 mode, the RxMF pulse is 244ns wide and its center identifies basic frame 0 of the received multiframe. If the Tx8KEN control bit (Address YF1) is 1 then the RxMF pin outputs an 8kHz frame pulse synchronous with the data stream on TPOS/TNEG. See Figure 43 and Figure 45 In T1 IMA mode, the frame pulse duration is 648ns. In E1 mode, (and E1 IMA mode) the RxMF pulse is 244ns wide and its center identifies basic frame 0 of the received CAS (Channel Associated Signaling) multiframe boundary or the received CRC-4 multiframe boundary as determined by the MFSEL control bit (Address Y02). If the Tx8KEN control bit (Address Y02) is 1 then the RxMF pin outputs and 8kHz frame pulse synchronous with the data stream on TPOS/TNEG. See Figure 62 and Figure 64.
14 94
F4 T12
DSTi[0] DSTi[4]
I
Data ST-BUS. This pin is an input for the transmit side of the framer. In 2.048Mbit/s ST-BUS mode and IMA mode it operates the same as DSTi(1-3), it can also operate in 8.192Mbit/s ST-BUS mode. IMA mode is not available at 8.192Mbit/s. The DSTi data stream is clocked into the framer by the clock input to pin CKi. When operated in 8.192Mbit/s ST-BUS mode this pin accepts a data stream containing 128 8-bit channels accommodating four framers. See Table 2 and Table 5. The frame boundary is indicated by the FPi inputs. Pin DSTi[0] is used by Framers[0-3] and pin DSTi[4] is used by Framers[4-7]. In 8.192Mbit/s mode, the 32 ST-BUS channels mapped to each framer are treated as described for DSTi(1-3) operating at 2.048Mbit/s.
14
SEMICMF.019
Data Sheet
Pin Description (continued)
Pin # LQFP 34 54 74 114 134 154 LBGA L2 R4 T6 M14 H16 C14 Name DSTi[1] DSTi[2] DSTi[3] DSTi[5] DSTi[6] DSTi[7] Type I Description (see Notes 1 to 7)
MT9072
Data ST-BUS. In 2.048Mbit/s ST-BUS mode and IMA mode this pin is an input for the transmit side of the framer. This pin is not used in 8.192Mbit/s ST-BUS mode. The DSTi data stream is clocked into the framer by the clock input to pin CKi. Pins DSTi[0-7] are used by Framers[0-7] respectively. In T1 mode, this pin accepts a 2.048Mbit/s ST-BUS stream. The first 24 ST-BUS channels contain the data to be transmitted on the PCM24 interface. See Table 1. In T1 IMA mode, this pin accepts a 1.544Mbit/s serial stream that contains a framing bit followed by the 24 8-bit channels to be transmitted on the PCM24 interface, see Table 3. The framing bit is ignored and an internally generated framing bit is used. IMA mode is selected by setting the IMA bit (Address Y00) to 1. In E1 mode, this pin accepts a 2.048Mbit/s ST-BUS stream that contains the data to be transmitted on the PCM30 interface. See Table 4 and Table 6. In E1 IMA mode, this pin accepts a 2.048Mbit/s ST-BUS stream that contains the data to be transmitted on the PCM30 interface. IMA mode is selected by setting the IMA bit (Address Y00) to 1. See Table 4 and Table 6.
15 95
G1 T13
DSTo[0] DSTo[4]
O
Data ST-BUS. This pin is an output for the receive side of the framer. In 2.048Mbit/s ST-BUS mode and IMA mode it operates the same as DSTo(1-3), it can also operate in 8.192Mbit/s ST-BUS mode. IMA mode is not available at 8.192Mbit/s. The DSTo data stream is clocked out of the framer by the clock input to pin CKi. When operated in 8.192Mbit/s ST-BUS mode this pin outputs a data stream containing 128 8-bit channels accommodating four framers. See Table 2 and Table 5. The frame boundary is indicated by the FPi inputs. Pin DSTo[0] is used by Framers[0-3] and pin DSTo[4] is used by Framers[4-7]. The 32 ST-BUS channels mapped to each framer are treated as described for DSTi(1-3) operating at 2.048Mbit/s.
SEMICMF.019
15
MT9072
Pin Description (continued)
Pin # LQFP 35 55 75 115 130 155 LBGA L3 T1 T7 M15 G13 C15 Name DSTo[1] DSTo[2] DSTo[3] DSTo[5] DSTo[6] DSTo[7] Type O Description (see Notes 1 to 7)
Data Sheet
Data ST-BUS. In 2.048Mbit/s ST-BUS mode and IMA mode this pin is an output for the receive side of the framer. This pin is not used in 8.192Mbit/s ST-BUS mode. Pins DSTo[0-7] are used by Framers[0-7] respectively. In T1 mode, this pin outputs 2.048Mbit/s ST-BUS data. The first 24 channels contain the 24 8-bit channels received on the PCM24 interface. Channel 31 bit 0 contains the received S-bit in D4 and ESF modes. See Table 1.The DSTo data stream is clocked out of the framer by the clock input to pin CKi. The DSTo pin is enabled if the DSToEN control bit (Address YF1) is set to 1. In T1 IMA mode, this pin outputs the 1.544Mbit/s received serial stream. The serial stream contains the framing bit followed by the 24 8-bit channels received on the PCM24 interface. See Table 3. In IMA mode the DSTo data stream is clocked out of the framer by the clock output by the RxDLC pin. The DSto pin is enabled if the DSToEN control bit (Address YF1) is set to 1. IMA mode is selected by setting the IMA bit (Address Y00) to 1. In E1 mode, this pin outputs 2.048Mbit/s ST-BUS data. The 32 channels contain the 32 channels of data received on the PCM30 interface. See Table 4 and Table 6. The DSTo data stream is clocked out of the framer by the clock input to pin CKi. The DSTo pin is enabled if the DSToE control bit (Address Y02) is set to 1. In E1 IMA mode, this pin outputs the 2.048Mbit/s received serial stream. See Table 4 and Table 6. In IMA mode the DSTo data stream is clocked out of the framer by the clock output by the RxDLC pin. The DSTo pin is enabled if the DSToE control bit (Address Y02) is set to 1. IMA mode is selected by setting the IMA bit (Address Y00) to 1.
16 96
G2 T14
CSTi[0] CSTi[4]
I
Control ST-BUS. This pin is the signaling input for the transmit side of the framer. In 2.048 Mbit/s ST-BUS mode it operates the same as CSTi(1-3), it can also operate in 8.192Mbit/s ST-BUS mode. The CSTi data stream is clocked into the framer by the clock input to pin CKi. This pin has no function in IMA mode. When operated in 8.192Mbit/s ST-BUS mode this pin accepts a data stream containing 128 8-bit channels accommodating four framers. See Table 2 and Table 5. The frame boundary is indicated by the FPi inputs. Pin CSTi[0] is used by Framers[0-3] and pin CSTi[4] is used by Framers[4-7]. The 32 ST-BUS channels mapped to each framer are treated as described for CSTi(1-3) operating at 2.048Mbit/s.
16
SEMICMF.019
Data Sheet
Pin Description (continued)
Pin # LQFP 36 56 76 116 136 156 LBGA L4 T2 T8 M16 G14 C16 Name CSTi[1] CSTi[2] CSTi[3] CSTi[5] CSTi[6] CSTi[7] Type I Description (see Notes 1 to 7)
MT9072
Control ST-BUS. In 2.048Mbit/s ST-BUS mode this pin is the signaling input for the transmit side of the framer. This pin has no function in 8.192Mbit/s ST-BUS mode or IMA mode. Pins CSTi[0-7] are used by Framers[0-7] respectively. The CSTi data stream is clocked into the framer by the clock input to pin CKi. In T1 robbed bit signaling mode the first 24 ST-BUS channels contain (XXXXABCD) signaling nibbles to be transmitted for their respective DS0s. The least significant nibbles (bits 3-0) are valid and the most significant nibbles of each channel are ignored. In T1 CCS (Common Channel Signaling) mode, the CSTi pin can be connected to the output of an external multi-channel HDLC. Any one of the framer's transmit timeslots can be programmed to transmit the data appearing at the CSTi pin on any one of the first 24 ST-BUS channels. See the descriptions of the CSIGEN control bit (Address Y04) and the Common Channel Signaling Map Register (Address Y0B). In E1 CAS (Channel Associated Signaling) mode, the 32 ST-BUS channels contain (XXXXABCD) signaling nibbles to be transmitted for their respective timeslots. The least significant nibbles (bits 3-0) are valid and the most significant nibbles of each channel are ignored. See Table 25. In E1 CCS (Common Channel Signaling) mode, the CSTi pin can be connected to the output of an external multi-channel HDLC. The framer's transmit timeslots 15, 16 and 31 can each be programmed to transmit the data appearing at the CSTi pin on any one of the 32 STBUS channels. See the descriptions of the CSIG control bit (Address Y03) and the TS15E, TS16E and TS31E control bits (Address Y06) and see Table 27.
17 97
G3 T15
CSTo(0) CSTo[4]
OH Control ST-BUS. This pin is the signaling output for the receive side of the framer. In 2.048 Mbit/s ST-BUS mode it operates the same as CSTo(1-3), it can also operate in 8.192Mbit/s ST-BUS mode. The CSTo data stream is clocked out of the framer by the clock input to pin CKi. This pin has no function in IMA mode. When operated in 8.192Mbit/s ST-BUS mode this pin outputs a data stream containing 128 8-bit channels accommodating four framers. See Table 2 and Table 5. The CSTo[0] pin is used by Framers [0-3] and the CSTo[4] pin is used by Framers [4-7]. The frame boundary is indicated by the FPi inputs. FPi[0] is used for Framers[0-3] and FPi[4] is used for Framers[4-7]. The 32 ST-BUS channels mapped to each framer are treated as described for CSTo(1-3) operating at 2.048Mbit/s.
SEMICMF.019
17
MT9072
Pin Description (continued)
Pin # LQFP 37 57 77 117 137 157 LBGA M1 T3 N9 L13 G15 B13 Name CSTo[1] CSTo[2] CSTo[3] CSTo[5] CSTo[6] CSTo[7] Type Description (see Notes 1 to 7)
Data Sheet
OH Control ST-BUS. In 2.048Mbit/s ST-BUS mode this pin is the signaling output for the receive side of the framer. The CSTo data stream is clocked out of the framer by the clock input to pin CKi. This pin has no function in 8.192Mbit/s ST-BUS mode or IMA mode. Pins CSTo[0-7] are used by Framers[0-7] respectively. In T1 robbed bit signaling mode, the first 24 ST-BUS channels contain (XXXXABCD) signaling nibbles received for their respective DS0s. The least significant nibbles (bits 3-0) are valid and the most significant nibbles of each channel are in a high impedance state. The CSTo pin is enabled if the CSToEN control bit (Address YF1) is set to 1. In T1 CCS (Common Channel Signaling) mode, the CSTo pin can be connected to the input of an external multi-channel HDLC. Any one of the framer's receive timeslots be programmed to output their received data on the CSTo pin on any one of the first 24 ST-BUS channels. CSTo is in a high impedance state during unused channels. See the descriptions of the CSIGEN control bit (Address Y04) and the Common Channel Signaling Map Register (Address Y0B). The CSTo pin is enabled if the CSToEN control bit (Address YF1) is set to 1. In E1 CAS (Channel Associated Signaling) mode, the 32 ST-BUS channels contain (XXXXABCD) signaling nibbles received for their respective timeslots. The least significant nibbles (bits 3-0) are valid and the most significant nibbles of each channel are in a high impedance state. See Table 26. The CSTo pin is enabled if the CSToE control bit (Address Y02) is set to 1. In E1 CCS (Common Channel Signaling) mode, the CSTo pin can be connected to the input of an external multi-channel HDLC. The framer's receive timeslots 15, 16 and 31 can each be programmed to output their received data on the CSTo pin during any one of the 32 ST-BUS channels. CSTo is in a high impedance state during unused channels. See the descriptions of the CSIG control bit (Address Y03) and the TS15E, TS16E and TS31E bits (Address Y06) and see Table 29. The CSTo pin is enabled if the CSToE control bit (Address Y02) is set to 1.
18 98
G4 T16
CKi[0] CKi[4]
I
System Clock. In 2.048Mbit/s ST-BUS mode and 8.192Mbit/s STBUS mode this pin accepts the clock that is used to time the transmit side and the receive side of the framer. The CKi clock rate is determined by control bits at (Address 900) In 2.048Mbit/s ST-BUS mode and in IMA mode, operation is the same as that described for pins CKi[1-3]. In 8.192Mbit/s ST-BUS mode this pin accepts the ST-BUS type 16.384MHz clock that is used to time the 8.192Mbit/s data appearing at pins DSTi, CSTi, DSTo and CSTo. In this mode pin CKi[0] is used by framers[0-3] and pin CKi[4] is used by framers[4-7]. See Figure 36. 8.192Mbit/s operation is not available in IMA mode.
18
SEMICMF.019
Data Sheet
Pin Description (continued)
Pin # LQFP 38 58 78 118 138 158 LBGA M2 T4 N10 L14 G16 B14 Name CKi[1] CKi[2] CKi[3] CKi[5] CKi[6] CKi[7] Type I Description (see Notes 1 to 7)
MT9072
System Clock. In 2.048Mbit/s ST-BUS mode this pin accepts the clock that is used to time the transmit side and receive side of the framer. In IMA mode it accepts the clock that is used to time the transmit side of the framer only. Pins CKi[0-7] are used to time Framers[0-7] respectively. The CKi clock rate is determined by control bits at (Address 900). This pin has no function in 8.192Mbit/s mode. In 2.048Mbit/s ST-BUS mode this pin accepts the ST-BUS type 4.096MHz clock that is used to time the data appearing at pins DSTi, CSTi, DSTo and CSTo. See Figure 34. In T1 IMA mode this pin accepts the 1.544MHz clock that is used to time the transmit data appearing at pin DSTi. IMA mode is selected by setting the IMA bit (Address Y00) to 1. See Figure 40. In E1 IMA mode this pin accepts the ST-BUS type 4.096MHz clock that is used to time the transmit data appearing at pins DSTi. IMA mode is selected by setting the IMA bit (Address Y00) to 1. In T1/E1 IMA mode the receive data stream is clocked out of pin DSTo by the clock output by pin RxDLC.
19 99
H1 R13
FPi[0] FPi[4]
I
Frame Pulse. This pin accepts a frame pulse that sets the basic frame boundary for the transmit and receive sides of the framer. The clock rate is determined by control bits at (Address 900) In 2.048Mbit/s mode and in IMA mode, operation is the same as that described for pins FPi[1-3]. In 8.192Mbit/s mode this pin accepts an 8.192Mbit/s ST-BUS type frame pulse which sets the frame boundary common to four framers. FPi[0] is used to set the frame boundary for Framers[0-3] and FPi[4] is used to set the frame boundary for Framers[4-7]. See Figure 36. 8.192Mbit/s operation is not available in IMA mode.
SEMICMF.019
19
MT9072
Pin Description (continued)
Pin # LQFP 39 59 79 119 139 159 LBGA M3 N5 N11 L15 F13 B15 Name FPi[1] FPi[2] FPi[3] FPi[5] FPi[6] FPi[7] Type I Description (see Notes 1 to 7)
Data Sheet
Frame Pulse. This pin accepts a frame pulse that sets the basic frame boundary for the transmit and receive sides of the framer. In IMA mode it accepts a frame pulse that sets the basic frame boundary for the transmit side of the framer only. Pins FPi[0-7] are used to set the frame boundaries for Framers[0-7] respectively. The clock rate is determined by control bits at (Address 900). This pin has no function in 8.192 Mbit/s mode. In 2.048Mbit/s ST-BUS mode this pin accepts an ST-BUS 2.048Mbit/s frame pulse that sets the basic frame boundary for the data that appears at pins DSTi, DSTo, CSTi and CSTo. See Figure 34. In T1 IMA mode, this pin accepts a 648ns frame pulse that sets the basic frame boundary for the transmit data that appears at pin DSTi. IMA mode is selected by setting the IMA bit (Address Y00) to 1. See Figure 40. In E1 IMA mode, this pin accepts a 2.048 Mbit/s ST-BUS type frame pulse that sets the basic frame boundary for the transmit data that appears at pin DSTi. IMA mode is selected by setting the IMA bit (Address Y00) to 1. In T1 IMA mode and E1 IMA mode, the basic frame boundary for the receive data stream that is output by DSTo is indicated by the clock output by the RxBF pin.
20 40 60 80 100 120 140 160
H2 M3 N6 N12 R14 L16 F14 B16
RxBF[0] RxBF[1] RxBF[2] RxBF[3] RxBF[4] RxBF[5] RxBF[6] RxBF[7]
O
Receive Basic Frame Pulse. This pin outputs a frame pulse that indicates the basic frame boundary for the received data stream output by the RxDL pin. In IMA mode the receive basic frame pulse also indicates the basic frame boundary in the received data stream output by the DSTo pin. Pins RxBF[0-7] are used to set the frame boundaries for Framers[0-7] respectively. In T1 mode, this pin provides a basic frame pulse that indicates the Sbit in the 1.544Mbit/s received data stream output by pin RxDL. See Figure 48. In T1 IMA mode, the Receive Basic Frame Pulse indicates the S-bit in the 1.544Mbit/s received data stream output by pin DSTo. IMA mode is selected by setting the IMA bit (Address Y00) to 1. See Figure 39. In E1 mode, this pin provides a 2.048 Mbit/s ST-BUS type frame pulse that indicates the beginning of channel 0 in the 2.048Mbit/s received data stream output by the RxDL pin. See Figure 69. In E1 IMA mode, the receive basic frame pulse indicates the beginning of channel 0 in the 2.048Mbit/s received data stream output by the DSTo pin. IMA mode is selected by setting the IMA bit (Address Y00) to 1. See Figure 58.
20
SEMICMF.019
Data Sheet
Pin Description (continued)
Pin # LQFP 163-178 LBGA A13,A14, A15,A16, B12,A12, C12,D12, A11,B11, C11,D11, C10,D10, B10,A10 B9,A9,C9, D9,B8,C8, A8,D8,D7, B7,C7,A7 Name D0-D15 Type Description (see Notes 1 to 7)
MT9072
I/O Data 0 to 15. These 16 signals form the bidirectional data bus for the non-multiplexed parallel processor interface. D15 is the most significant bit.
181-192
A0-A11
I
Address 0 to 11. These 12 signals form the input address bus for the non-multiplexed parallel processor interface. Bits A10 and A8 determine which of the eight framers is selected for read and write operations, bit A11 being high and A8 to A10 being low selects all eight framers for write operations. A11 and A8 being both high and A9 being low selects global control registers. A11 is the most significant bit. Chip Select. A zero enables the read and write functions of the MT9072 parallel processor interface; all bidirectional data bus lines (D0-D15) will operate normally. A one disables the read and write functions of the parallel processor interface; all bidirectional data bus lines (D0-D15) will be in a high impedance state. Data Strobe. Data Strobe for Motorola mode (I/M=0). The MT9072 reads data from the address bus (A0-A11) on the falling edge of DS; writes data to the bidirectional data bus (D0-D15) on the falling edge of DS (processor read); reads data from the bidirectional data bus (D0-D15) on the falling edge of DS (processor write). DS may be connected to CS. Read. Read for Intel type mode (I/M=1). The MT9072 reads data from the address bus (A0-A11) on the falling edge of RD; writes data to the bidirectional data bus (D0-D15) on the falling edge of RD (processor read). Read/Write. Read and Write for Motorola mode (I/M=0). A zero sets the MT9072 bidirectional data bus lines (D0-D15) as inputs for a processor write. A one sets the MT9072 bidirectional data bus lines (D0-D15) as outputs (processor read). Write. Write for Intel type mode (I/M=1). The MT9072 reads data from the address bus (A0-A11) on the falling edge of WR; reads data from the bidirectional data bus (D0-D15) on the rising edge of WR (processor write).
193
A6
CS
I
194
D6
DS
I
D6
(RD)
I
195
B6
R/W
I
B6
(WR)
I
196
C6
IRQ
OH Interrupt Request. When zero, one or more of the eight framers in the MT9072 has generated an interrupt request. When one, the MT9072 has not generated an interrupt request. IRQ is an open drain output that should be connected to VDD through a pull-up resistor. CS can be either high or low for this output pin to function. I Intel / Motorola. High configures the processor interface for Intel type of parallel non-multiplexed processors where RD and WR pins are used. Low configures the processor interface for Motorola type of parallel non-multiplexed processors where R/W and DS pins are used. See Figure 28 and Figure 29.
197
D5
IM
SEMICMF.019
21
MT9072
Pin Description (continued)
Pin # LQFP 198 LBGA C5 Name RESET Type I Description (see Notes 1 to 7)
Data Sheet
Reset. When zero, all eight framers of the MT9072 are in a reset condition where all registers are set to their default values. When one, all eight framers of the MT9072 operate normally where all registers may be programmed by the external processor. A valid reset condition requires this input to be held low for a minimum of 100ns. This input should be set to zero during initial power up, then set to one. Transmit Alarm Indication Signal. When zero, all eight framers of the MT9072 transmit an all ones signal (AIS) at the TPOS and TNEG output pins. When one, all eight framers of the MT9072 transmit data normally. This input is typically set to zero during initial power up, then set to one. Transmit Multiframe Boundary. This pin accepts a frame pulse that sets the multiframe boundary for the framer transmitters. The device will generate its own multiframe boundary if this pin is held high. The TxMF pin is held high in most applications. This input is common for all eight framers, and is enabled on a per framer basis with a control register bit. Operation is identical in 2.048 Mbit/s and 8.192 Mbit/s modes. In T1 mode the frame pulse applied to this pin sets the transmitted D4/ESF multiframe boundary. The falling edge of this frame pulse identifies basic frame 0 on the ST-BUS data stream (DSTi). This input is enable with control bit TxMFSEL (Address YF1). See Figure 41. In E1 mode the frame pulse applied to this pin sets the transmitted channel associated signaling (CAS) multiframe boundary or the transmitted CRC-4 multiframe boundary. The falling edge of this frame pulse identifies basic frame 0 on the ST-BUS data stream (DSTi) of the 16 frame multiframe. This input is enabled with control bit MFBE (Address Y02). See Figure 60.
199
A5
TAIS
I
200
B5
TxMF
I
201 202 203 204
A4 B4 C4 A3
RSV RSV RSV TDI
----
This pin should be tied low. This pin should be tied low. This pin should be tied low.
IPu Test Data Input. One of five signals (TDI, TDO, TMS, TCK & TRST) making up the Test Access Port (TAP) of the IEEE 1149.1-1990 Standard Test Port and Boundary-Scan Architecture. The TAP provides access to test support functions built into the MT9072. The TAP is also referred to as a JTAG (Joint Test Action Group) port. OH Test Data Output. Depending on the sequence previously applied to the TMS input, the contents of either the instruction register or data register are serially shifted out towards the TDO. The data out of the TDO is clocked on the falling edge of the TCK pulses. When no data is shifted through the boundary scan cells, the TDO driver is set to a high impedance state. See the pin description for TDI and the section on JTAG.
205
A2
TDO
22
SEMICMF.019
Data Sheet
Pin Description (continued)
Pin # LQFP 206 LBGA B3 Name TMS Type Description (see Notes 1 to 7)
MT9072
IPu Test Mode Select Input. The logic signals received at the TMS input are interpreted by the TAP Controller to control the test operations. The TMS signals are sampled at the rising edge of the TCK pulse. Internally pulled up to VDD. See the pin description for TDI and the section on JTAG. IPu Test Clock Input. TCK provides the clock for the test logic. The TCK does not interfere with any on-chip clocks and thus remains independent. The TCK permits shifting of test data into or out of the Boundary-Scan register cells concurrently with the operation of the device and without interfering with the on-chip logic. Internally pulled up to VDD. See the pin description for TDI and the section on JTAG. See Figure 30. IPu Test Reset. When zero, the JTAG scan structure is reset. When one, the JTAG scan structure operates normally. Internally pulled up to VDD. See the pin description for TDI and the section on JTAG. A valid device reset condition requires this input to be held low for a minimum of 100ns. This input is should be set to zero during initial power up, then set to one if the JTAG port is to be used, otherwise, it may be permanently set to zero. -This pin should be tied low.
207
B2
TCK
208
C3
TRST
--
B1
RSV
Notes: 1. All inputs are CMOS with CMOS compatible logic levels. 2. All unused inputs should be tied low. 3. All outputs are CMOS and are compatible with CMOS logic levels. 4. See AC Electrical Characteristics - Timing Parameter Measurement Voltage Levels for input and output voltage thresholds. 5. The number enclosed in parentheses following the pin name identifies the framer as follows: [0] - framer 0, [1] - framer 1, [2] - framer 2,... [7] - framer 7 6. The "Y" character in the register address symbolizes the upper 4 address bits (A11A10A9A8) which identify the particular framer addressed within the MT9072 as follows: [0] 0000 - framer 0, [1] 0001 - framer 1,... [2] 0010 - framer 2,... [7] 0111 - framer 7 [8] 1000 - all 8 framers. 7. Pin types are as follows: I - input(5 V tolerant input IP - input with a pullup or pulldown, these are 3 V tolerant inputs. O - output I/O - input and output OH - output and high impedance OD - output open drain
SEMICMF.019
23
MT9072
Data Sheet
24
SEMICMF.019
Data Sheet Table of Contents
MT9072
Features .................................................................................................................................. 1 Applications ............................................................................................................................ 1 Description .............................................................................................................................. 1 MT9072 Detailed Feature Summary ...................................................................................... 2 1.0 Overview .......................................................................................................................... 29
1.1 Standards Compliance ............................................................................................................................. 29 1.2 Microprocessor Port ................................................................................................................................. 29 1.3 Interface to the Physical Layer Device ..................................................................................................... 29 1.4 Interface to the System Backplane........................................................................................................... 29 1.5 Framing Modes......................................................................................................................................... 29 1.6 Access to the Maintenance Channel ........................................................................................................ 29 1.7 Robbed Bit Signaling/Channel Associated Signaling ............................................................................... 30 1.8 Common Channel Signaling..................................................................................................................... 30 1.9 HDLCs ...................................................................................................................................................... 30 1.10 Performance Monitoring and Debugging................................................................................................ 30 1.11 Interrupts ................................................................................................................................................ 30
2.0 PCM24 Interface (T1)....................................................................................................... 30
2.1 T1 Interface to the System Backplane...................................................................................................... 30 2.2 T1 Interface to the Physical Layer Device ............................................................................................... 33 2.3 T1 Line Coding ......................................................................................................................................... 33 2.4 T1 Pulse Density ..................................................................................................................................... 33
3.0 PCM30 Interface (E1)....................................................................................................... 34
3.1 E1 Interface to the System Backplane ..................................................................................................... 34 3.2 E1 Interface to the Physical Layer Device................................................................................................ 35
4.0 Framing ............................................................................................................................ 36
4.1 T1 Framing ............................................................................................................................................... 36 4.1.1 T1 D4 Framing ................................................................................................................................ 37 4.1.2 T1 ESF Framing.............................................................................................................................. 38 4.1.3 T1 T1DM Framing........................................................................................................................... 39 4.1.4 T1 G.802 Mode ............................................................................................................................... 39 4.2 E1 Framing ............................................................................................................................................... 40 4.2.1 E1 Basic Framing (Timeslot 0)........................................................................................................ 41 4.2.2 E1 CRC-4 Multiframing (Timeslot 0) ............................................................................................... 41 4.2.2.1 E1 Automatic CRC-4 Interworking......................................................................................... 43 4.2.3 E1 Channel Associated Signaling (CAS) Multiframing (Timeslot 16) ............................................. 44 4.2.4 E1 Framing Algorithm ..................................................................................................................... 44 4.2.4.1 Notes for Synchronization State Diagram (Figure 7)............................................................. 44
5.0 Elastic Buffer ................................................................................................................... 46
5.1 Transmit Elastic Buffer ............................................................................................................................. 48
6.0 Data Link .......................................................................................................................... 49
6.1 T1 Data Link ............................................................................................................................................. 49 6.1.1 T1 Data Link (DL) Pin Access......................................................................................................... 49 6.1.1.1 T1 Data Link (DL) Pin Data Received from PCM24 .............................................................. 49 6.1.1.2 T1 Data Link (DL) Pin Data Sent to PCM24 .......................................................................... 50 6.2 E1 Data Link (DL) Operation .................................................................................................................... 50 6.2.1 E1 Data Link (DL) Pin Access......................................................................................................... 51 6.2.1.1 E1 Data Link (DL) Pin Data Transmitted on PCM30 ............................................................. 51 6.2.1.2 E1 Data Link (DL) Pin Data Received on PCM30 - With No Elastic Buffer ........................... 51 6.2.1.3 E1 Data Link (DL) Pin Data Received on PCM30 - With Elastic Buffer................................. 51 6.2.2 E1 Data Link (DL) National Bit Buffer Access................................................................................. 52 6.2.3 E1 Data Link (DL) ST-BUS Access................................................................................................. 52 6.2.4 E1 Timeslot 0 CRC-4 NFAS Receive from PCM30 to DSTo .......................................................... 53 6.3 T1 Bit Oriented Message.......................................................................................................................... 53
SEMICMF.019
25
MT9072
Table of Contents
Data Sheet
7.0 Signaling...........................................................................................................................55
7.1 T1 Signaling ..............................................................................................................................................55 7.1.1 T1 Robbed Bit Signaling..................................................................................................................55 7.1.2 T1 Common Channel Signaling.......................................................................................................56 7.2 E1 Signaling ..............................................................................................................................................56 7.2.1 Channel Associated Signaling (CAS) Operation .............................................................................56 7.2.2 E1 Channel Associated Signaling (CAS) Register and ST-BUS Access.........................................58 7.2.2.1 E1 Channel Associated Signaling (CAS) Transmit from ST-BUS CSTi to PCM30................59 7.2.2.2 E1 Channel Associated Signaling (CAS) Receive from PCM30 to ST-BUS CSTo................59 7.2.3 E1 Common Channel Signaling (CCS) Transmit from ST-BUS CSTi and DSTi to PCM30 ............60 7.2.4 E1 Common Channel Signaling (CCS) Receive from PCM30 to CSTo and DSTo .........................60 7.2.5 CCS (Timeslot 16) Programming Options Summary Table.............................................................61
8.0 HDLC.................................................................................................................................63
8.1 HDLC Description .....................................................................................................................................63 8.1.1 HDLC Frame Structure....................................................................................................................64 8.1.2 Data Transparency (Zero Insertion/Deletion) ..................................................................................64 8.1.3 Invalid Frames .................................................................................................................................64 8.1.4 Frame Abort.....................................................................................................................................65 8.1.5 Interframe Time Fill and Link Channel States .................................................................................65 8.1.6 Go-Ahead ........................................................................................................................................65 8.1.7 Functional Description .....................................................................................................................65 8.1.8 HDLC Transmitter............................................................................................................................65 8.1.9 HDLC Receiver................................................................................................................................66
9.0 MT9072 Access and Control...........................................................................................68
9.1 Processor Interface (A11-A0, D15-D0, I/M, DS, R/W, CS, IRQ, Pins)......................................................68 9.1.1 Framer and Register Access ...........................................................................................................68 9.1.1.1 CS and IRQ............................................................................................................................68 9.1.2 ST-BUS Interface (DSTi, DSTo, CSTi, CSTo Pins).........................................................................68 9.1.3 IMA Interface (DSTi, DSTo, Pins)....................................................................................................69 9.1.4 Signaling Multiframe Boundary (RxMF, TxMF Pins).......................................................................69 9.1.5 Control Pins .....................................................................................................................................69 9.1.5.1 Reset Operation (RESET Pin, RST Bit and RSTC Bit) ..........................................................69 9.1.5.2 Transmit AIS Operation (TAIS Pin) ........................................................................................72 9.1.5.3 IEEE 1149.1-1990 Test Access Port (TAP) ...........................................................................72 9.1.6 Data Link (DL) Interface (RxDL, RxDLC, TxDL, TxDLC Pins).........................................................72 9.1.7 Multiframe Boundary (RxMF, TxMF Pins) .......................................................................................72
10.0 ST-BUS Analyzer ...........................................................................................................72 11.0 Loopbacks......................................................................................................................72
11.1 T1 Loopbacks..........................................................................................................................................72 11.2 T1 In Band Loopback Codes...................................................................................................................74 11.3 E1 Loopbacks .........................................................................................................................................75
12.0 Performance Monitoring ...............................................................................................77
12.1 T1 Error Counters ...................................................................................................................................77 12.2 E1 Error Counters ..................................................................................................................................78
13.0 Maintenance and Alarms ..............................................................................................80
13.1 T1 Maintenance and Alarms ...................................................................................................................80 13.1.1 T1 Error Insertion...........................................................................................................................80 13.1.2 T1 Per Timeslot Control.................................................................................................................80 13.1.3 T1 Per Timeslot Looping ...............................................................................................................80 13.1.4 T1 Pseudo-Random Bit Sequence (PRBS) Testing ......................................................................80 13.1.5 T1 Mu-law Milliwatt ........................................................................................................................81 13.1.6 T1 Alarms ......................................................................................................................................82 13.1.7 T1 Per Timeslot Trunk Conditioning ..............................................................................................83 13.2 E1 Maintenance and Alarms ...................................................................................................................83
26
SEMICMF.019
Data Sheet Table of Contents
MT9072
13.2.1 E1 Error Insertion.......................................................................................................................... 84 13.2.2 E1 Per Timeslot Control................................................................................................................ 84 13.2.3 E1 Per Timeslot Looping............................................................................................................... 84 13.2.4 E1 Pseudo-Random Bit Sequence (PRBS) Testing ..................................................................... 84 13.2.5 E1 A-law Milliwatt.......................................................................................................................... 85 13.2.6 E1 Alarms ..................................................................................................................................... 85 13.2.7 E1 Automatic Alarms .................................................................................................................... 86
14.0 Interrupts........................................................................................................................ 86
14.1 Interrupt Status Register Overview......................................................................................................... 87 14.1.1 Interrupt Related Control Bits and Pins......................................................................................... 88 14.2 Interrupt Servicing Methods.................................................................................................................... 88 14.2.1 Polling Method .............................................................................................................................. 88 14.2.2 Vector Method............................................................................................................................... 88 14.3 T1 Interrupt Vector and Interrupt Source Summary ............................................................................... 89 14.4 E1 Interrupt Vector and Interrupt Source Summary ............................................................................... 90 14.5 E1 Interrupt Source and Interrupt Status Register Summary ................................................................. 92
15.0 JTAG (Joint Test Action Group) Operation ................................................................ 94
15.1 Test Access Port (TAP) .......................................................................................................................... 94 15.2 Test Access Port (TAP) Controller ......................................................................................................... 95 15.3 Instruction Register................................................................................................................................. 95 15.4 JTAG Data Registers.............................................................................................................................. 96 15.4.1 Identification Register ................................................................................................................... 96
16.0 MT9072 Register Set ..................................................................................................... 96
16.1 T1 Register Set....................................................................................................................................... 96 16.1.1 Register Address (000 - FFF) Summaries .................................................................................... 96 16.1.1.1 Framer Address (0XX-9XX) Summary ............................................................................... 96 16.1.1.2 Register Group Address (Y00 - YFF) Summary.................................................................. 97 16.1.1.3 Global Control and Status Register (900-91F) Summary.................................................... 98 16.1.1.4 Master Control Registers Address (Y00-Y0F, YF0 to YFF) Summary ................................ 98 16.1.1.5 Master Status Registers Address (Y10-Y1F) Summary .................................................... 101 16.1.1.6 Latched Status Registers Address (Y20-Y2F) Summary .................................................. 102 16.1.1.7 Interrupt Status Registers Address (Y30-Y3F) Summary.................................................. 103 16.1.2 Interrupt Mask Registers Address (Y40-Y4F) Summary............................................................. 104 16.1.3 Master Control Registers (Y00 to YF0 ) Bit Functions ............................................................... 104 16.1.4 Master Status Registers(Y10-Y18)Bit Functions ........................................................................ 115 16.1.5 Latched Status Registers (Y20 - Y2F) Bit Functions .................................................................. 121 16.1.6 Interrupt Status Registers (Y30 - Y3F) Bit Functions................................................................. 127 16.1.7 Interrupt Mask Registers (Y40 - Y4F) Bit Functions .................................................................. 127 16.1.8 Per Channel Control and Data (Y50 - YAF) Bit Functions ......................................................... 131 16.1.9 Master Control Registers (YF1 to YF7) Bit Functions................................................................. 133 16.1.10 Global Control and Status Registers (900 - 91F) Bit Functions ................................................ 138 16.1.11 E1 Register Set......................................................................................................................... 146 16.2 Register Address (000 - FFF) Summaries............................................................................................ 146 16.2.0.1 Framer Address (000-FFF) Summary ............................................................................... 146 16.2.0.2 Register Group Address (Y00 - YFF) Summary................................................................ 147 16.2.0.3 Global Control and Status Register (900-91F) Summary.................................................. 149 16.2.1 Register Address (Y00 - YFF) Summary .................................................................................... 149 16.2.1.1 Master Control Registers Address (Y00-Y0F, YF0-YFF) Summary .................................. 150 16.2.1.2 Master Status Registers Address (Y10-Y1F) Summary .................................................... 151 16.2.1.3 Latched Status Registers Address (Y20-Y2F) Summary .................................................. 152 16.2.1.4 Interrupt Status Registers Address Summary(Y3X) .......................................................... 153 16.2.1.5 Interrupt Mask Registers Address Summary(Y4X)............................................................ 154 16.2.1.6 Transmit CAS Data Registers Address (Y50-Y6F) Summary ........................................... 154 16.2.1.7 Receive CAS Data Registers Address (Y70-Y8F) Summary ............................................ 155 16.2.1.8 Timeslot 0-31 Control Registers Address (Y90-YAF) Summary ....................................... 156
SEMICMF.019
27
MT9072
Table of Contents
Data Sheet
16.2.1.9 Transmit National Bit Data Register(R/W) Address(YB0 to YB4) Summary......................159 16.2.1.10 Receive National Bit Data Register(R/W) Address(YC0 to YC4) Summary ....................159 16.2.2 Master Control Registers (Y00 - Y09) Bit Functions....................................................................160 16.2.3 Master Status Registers (Y10 - Y1A) Bit Functions.....................................................................169 16.2.4 Latched Status Registers (Y2X) Bit Functions ..........................................................................180 16.2.5 Interrupt Vector and Interrupt Status Registers (Y3X) Bit Functions ...........................................188 16.2.6 Interrupt Vector Mask and Interrupt Mask Registers (Y4X) Bit Functions ...................................193 16.2.7 Transmit CAS (ABCD) Data Registers (Y51 - Y6F) Bit Functions...............................................198 16.2.8 Receive CAS (ABCD) Data Registers (Y71 - Y8F) Bit Functions................................................199 16.2.9 Timeslot 0-31 Control Registers (Y90 - YAF) Bit Functions ........................................................199 16.2.10 Transmit National Bit RN Data Registers (YB0- YB4) Bit Functions .....................................200 16.2.11 Receive National Bit RN Data Registers (YC0- YC4) Bit Functions ......................................201 16.2.12 Master Control Registers (YF0 - YF6) Bit Functions .............................................................202 16.2.13 Global Control and Status Registers(900-91F) Bit Functions....................................................204
17.0 Applications .................................................................................................................213
17.1 T1 Applications......................................................................................................................................213 17.2 E1 Applications .....................................................................................................................................219
18.0 AC/DC Electrical Characteristics ...............................................................................229
18.1 General .................................................................................................................................................229 18.2 T1 Mode ................................................................................................................................................237 18.2.1 AC Electrical Characteristics - PCM24 and ST-BUS Frame Format ...........................................247 18.3 E1 Mode................................................................................................................................................247 18.4 AC Electrical Characteristics - PCM30 and ST-BUS Frame Format.....................................................259
19.0 Applicable Specifications ...........................................................................................259 Packaging ............................................................................................................................260
28
SEMICMF.019
Data Sheet
1.0 Overview
MT9072
The MT9072 is an eight port (octal) framing device that can be software configured for T1, E1 or J1 operation. Each of the eight framers can be independently timed and controlled. Each framer features one embedded HDLC (High-level Data Link Controller) that can be assigned to the maintenance channel or to any other channel.
1.1
Standards Compliance
In T1 mode, the MT9072 meets or supports the latest recommendations including AT&T PUB43801, TR-62411, ANSI T1.102, T1.403 and T1.408. It also supports Telcordia GR-303-CORE. In T1 ESF mode the CRC-6 calculation and yellow alarm can be configured to meet the requirements of a J1 interface. In E1 mode, the MT9072 meets or supports the latest ITU-T Recommendations for PCM30 and ISDN primary rate including G.703, G.704, G.706, G.732, G.775, G.796, G.823, G.965 (V5.2) and I.431. It also meets or supports ETSI TBR4, TBR13, ETS 300 233, and ETS 300 347 (V5.2).
1.2
Microprocessor Port
A 16-bit parallel Motorola or Intel non-multiplexed microprocessor interface is used to access the control and status registers.
1.3
Interface to the Physical Layer Device
On the line side the MT9072 framers interface to physical layer devices (typically LIUs) using a Return to Zero (RZ) or Non Return to Zero (NRZ) protocol. The data can be single rail or dual rail with several T1 and E1 line coding options available. In T1 mode, the receive and transmit paths each include a two-frame slip buffer. The transmit slip buffer features programmable delay and it serves as a rate converter between the ST-BUS and the 1.544Mbit/s T1 line rate. In E1 mode, the receive path includes a two-frame slip buffer.
1.4
Interface to the System Backplane
On the system side the MT9072 framers can interface to a 2.048Mbit/s or 8.192Mbit/s ST-BUS backplane, or a 2.048 Mbit/s GCI backplane. There is an IMA (Inverse MUX for ATM) mode for IMA applications, this enables the framer to interface to a 1.544Mbit/s (T1) or 2.048Mbit/s (E1) serial bus with asynchronous transmit and receive timing.
1.5
Framing Modes
The MT9072 framers operate in termination mode or transparent mode. In the receive transparent mode, the received line data is channelled to the DSTo pin with arbitrary frame alignment. In the transmit transparent mode, no framing or signaling is imposed on the data transmitted from the DSTi pin onto the line. In T1 mode the framers operate in any of the following framing modes: D4, Extended Superframe (ESF) or T1DM. In E1 mode the framers run three framing algorithms: basic frame alignment, signalling multiframe alignment and CRC-4 multiframe alignment. The Remote Alarm Indication (RAI) bit is automatically controlled by an internal state machine.
1.6
Access to the Maintenance Channel
SEMICMF.019
29
MT9072
Data Sheet
The T1 ESF Facility Data Link (FDL) bits can be accessed in the following three ways: Through the data link pins TxDL, RxDL, RxDLC and TxDLC or through internal registers for Bit Oriented Messages or through the embedded HDLC. In E1 mode the Sa bits (bits 4-8 of the non-frame alignment signal) can be accessed in four ways: Through data link pins TxDL, RxDL, RxDLC and TxDLC or through single byte transmit and receive registers or through five byte transmit and receive national bit buffers or through the embedded HDLC.
1.7
Robbed Bit Signaling/Channel Associated Signaling
Robbed bit signaling and channel associated signaling information can be accessed two ways: Via the microport; via the CSTi and CSTo pins. Signaling information is frozen upon loss of multiframe alignment. In T1 mode the MT9072 supports AB and ABCD robbed bit signaling. Robbed bit signaling can be enabled on a channel by channel basis. In E1 mode the MT9072 supports Channel Associated Signaling (CAS) multiframing.
1.8
Common Channel Signaling
MT9072 supports Common Channel Signaling (CCS) with the embedded HDLCs and with the capability to map external HDLCs to/from the transmit/receive timeslots. In T1 mode CCS is supported in any one channel by using the embedded HDLC. Alternatively, the CSTi and CSTo pins can be used to map an external HDLC channel to/from any one transmit/receive T1 channel. In E1 mode CCS is supported in any one timeslot by using the embedded HDLC. Alternatively, the CSTi and CSTo pins can be used to map three external HDLC channels to/from any of transmit/receive E1 timeslots 15, 16 and 31.
1.9
HDLCs
The MT9072 provides one embedded HDLC per framer with 32 byte deep transmit and receive FIFOs. In T1 mode the embedded HDLC can be assigned to the FDL or any channel. It can operate at 4kbit/s (Data Link), 56kbit/s or 64kbit/s. In E1 mode the embedded HDLC can be assigned to timeslot zero Sa bits (bits 4-8 of the non-frame alignment signal), or any other timeslot. It can operate at 4,8,12,16,20 (Data Link) or 64kbit/s.
1.10
Performance Monitoring and Debugging
The MT9072 has a comprehensive suite of performance monitoring and debugging features. These include error counters, loopbacks, deliberate error insertion and a 215 -1 QRS/PRBS generator/detector.
1.11
Interrupts
The MT9072 provides a comprehensive set of maskable interrupts. Interrupt sources consist of synchronization status, alarm status, counter indication and overflow, timer status, slip indication, maintenance functions and receive signaling bit changes.
2.0
2.1
PCM24 Interface (T1)
T1 Interface to the System Backplane
30
SEMICMF.019
Data Sheet
MT9072
PCM24 (T1) basic frames are 193 bits long and are transmitted at a frame repetition rate of 8000 Hz, which results in an aggregate bit rate of 193 bits x 8000/sec =1.544 Mbits/sec. Basic frames are divided into 24 channels numbered 1 to 24 and a framing bit; see Figure 4. Each timeslot is 8 bits in length and is transmitted most significant bit first (numbered bit 1). This results in a single channel data rate of 8 bits x 8000/sec. = 64 kbit/s.
DS1 FRAME
125us CHANNEL 24 S BIT CHANNEL 1 CHANNEL 23 CHANNEL 24 S BIT CHANNEL 1
*********
(1/1.544)us
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
BIT 8
(8/1.544)us
Figure 4 - PCM24 Link Frame Format (T1) It should be noted that the Zarlink ST-BUS has 32 channels numbered 0 to 31 and the most significant bit of an eight bit channel is numbered bit 7, see Figure 5. Therefore, ST-BUS bit 7 is synonymous with DS0 bit 1; bit 6 with bit 2 and so on. See Zarlink Application note MSAN-126 for more details on the ST-BUS.
125s CHANNEL 31 or 127 CHANNEL 0
***
CHANNEL 30 or 126
CHANNEL 31 or 127
CHANNEL 0
Most Significant Bit (First)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Least Significant Bit (Last)
(8/2.048 or 8/8.192)s
Figure 5 - ST-BUS Format In the case of mapping ST-BUS to the PCM24 payload, only the first 24 channels and the last channel (31) of an ST-BUS are used (see Table 1). Timeslot 31 S-bit is only used if TXSYNC bit Y00 is set. All unused channels are tristate. The relationship between DSTi/CSTi and the voice channels in 8.192 Mbit/s mode is shown in Table 2 (F01-F7 refer to the Framer numbers). There are 2 multiplexed streams (DSTi/o0 and CSTi/o0 are used to multiplexed data for Framers 0 to 3 and DSTi/o4 and CSTi/o4 is used for framers 5 to 7). When the device is in IMA (Inverse Mux for ATM) mode, the mapping is the S-bit followed by 24 PCM channels.
SEMICMF.019
31
MT9072
Data Sheet
This relationship is shown in Table 3. Note that the S-bit location in the Table is indicated by the bit number; which starts from bit 0. Hence the strict definition of ST-BUS channels is not adhered to. As in a T1 interface the data on the DSTi/o is a bit followed by 24 channels. When signaling information is written to the MT9072 using ST-BUS control links (as opposed to direct writes by the microport to the on-board signaling registers), the CSTi channels corresponding to the selected DSTi channel streams are used to transmit the signaling bits. Since the maximum number of signaling bits associated with any channel is 4 (in the case of ABCD), only half a CSTi (bits 3 to 0) channel is required for sourcing the signaling bits. Bit A is bit 3 from the CSTi stream, Bit B is 2, Bit C is 1, and Bit D is 0. Unused channels and unused bits are tristate. In T1 transparent mode, the DSTi data is transparently sent to the PCM24 channels. In transparent mode the data on the DSTi streams will appear unaltered on the PCM24 links and data received on the PCM24 link will pass unaltered to the DSTo streams. No signaling insertion or extraction is done in transparent mode. If the TxSYNC control bit (address Y00) is 1 then the transmit S-bit is overwritten by channel 31 bit 0 in the 2.048 Mbit/s ST-BUS mode. In the 8.192 Mbit/s ST-BUS mode the S-bits from channels 124,125,126,127 respectively are used to override the transmit S-bit positions for Framers 0 to 3 or 4 to 7 respectively. If T1 Transparent mode and IMA mode are both selected then the S-bit and channel bits are transparently mapped as shown in Table 3. Table 1 - ST-BUS vs. PCM24 Channel Relationship for 2.048 Mbit/s DST/CST Streams (T1) PCM24 Channels ST-BUS Channels (DSTi/o and CSTi/o) PCM24 Channels ST-BUS Channels (DSTi/o and CSTi/o) 1 0 17 16 2 1 18 17 3 2 19 18 4 3 20 19 5 4 21 20 6 5 22 21 7 6 23 22 8 7 24 23 9 7 24 x 10 9 25 x 11 10 26 x 12 11 27 x 13 12 28 x 14 13 29 x 15 14 30 x 16 15 S-bit 31
Table 2 - ST-BUS Channel vs. PCM24 Channel Relationship for 8.192 Mbit/s DST/CST Streams (T1) PCM24 Channels ST-BUS Chan(DSTi/o and CSTi/o) F0/4 F1/5 F2/6 F3/7 1 0 1 2 3 17 64 65 66 67 2 4 5 6 7 18 68 69 70 71 3 8 9 10 11 19 72 73 74 75 4 12 13 14 15 20 76 77 78 79 5 16 17 18 19 21 80 81 82 83 6 20 21 22 23 22 84 85 86 87 7 24 25 26 27 23 88 89 90 91 8 28 29 30 31 24 92 93 94 95 9 32 33 34 35 S-bit 124 125 126 127 10 36 37 38 39 11 40 41 42 43 12 44 45 46 47 13 48 49 50 51 14 52 53 54 55 15 56 57 58 59 16 60 61 62 63 -
PCM24 Channels ST-BUS Chan(DSTi/o and CSTi/o) F0/4 F1/5 F2/6 F3/7
32
SEMICMF.019
Data Sheet
MT9072
S bit Bit 0 16 15 1 0 17 16 2 1 18 17 3 2 19 18 4 3 20 19 5 4 21 20 6 5 22 21 7 6 23 22 8 7 24 23 9 8 10 9 11 10 12 11 13 12 14 13 15 14
PCM24 Channels ST-BUS Channels (DSTi/o) PCM24 Channels ST-BUS Channels (DSTi/o)
Table 3 - ST-BUS vs. PCM24 to Channel Relationship for IMA DST Streams (T1)
2.2
T1 Interface to the Physical Layer Device
Control bits in the Line Interface and Coding word (address Y01) determine the format of the PCM24 transmit and receive signals. Three physical interface formats are provided including RZ dual rail, NRZ dual rail and NRZ single rail. The detailed timing diagrams are presented in Figures 45 to Figures 48. RZ Dual Rail - On the Transmit side the pulse width is approximately half the duration of the PCM24 bit cell centered around the falling edge of TXCL. On the receive side RPOS and RNEG are sampled on the falling edge of EXCLi. Note that the CLKE bit in register Y01(selectable for edge sampling) has no effect in RZ mode. NRZ Dual Rail - With this format, pulses are present for the full bit cell, which allows the set-up and hold times to be easily met. For the receiver the sampling point can be the rising edge or the falling edge of the EXCLi clock, depending on the CLKE bit in Register Y01. The transmitted data can be output either on the rising or falling edge of TXCL selected by the CLKE bit. TXCL is an input in T1 mode and an output in E1 mode. NRZ Single Rail - This NRZ format is not dual rail, and therefore, only requires a single output line and a single input line (i.e., TPOS and RPOS). The CLKE bit in Register Y01 controls the TXCL clock edge and the EXCLi sampling edge.
2.3
T1 Line Coding
B8ZS (zero code substitution) is selectable globally for both the transmit and receive path (register Y01). Jammed bit 7, GTE, DDS or BELL zero code suppression are also available for the transmitter and receiver(register Y01). Different schemes for provision of ones density can be selected with bits ZCS2:0 (registers Y01). GTE suppression is achieved by replacing the LSB of zero bytes by a one except for the signaling frame. DDS suppression is replacement of zero byte by 10011000. Bell code suppression is replacement of bit 1(second bit after LSB) of a zero byte. Jammed bit seven selection will replace the LSB of each channel with a '1'.
2.4
T1 Pulse Density
Bit 4 of address Y10 (PDV) toggles if the receive data fails to meet ones density requirements. It will toggle upon detection of 16 consecutive zeros in the line data, or if there are fewer than N ones in a window of 8(N+1) bits where N = 1 to 23. The transmit T1 data is monitored and if the 12.5% density requirement is not met over a maximum 192 bit window a one is inserted in a non-framing bit. The window and PDV criteria is the same as the received PDV.
SEMICMF.019
33
MT9072
3.0
3.1
Data Sheet
PCM30 Interface (E1)
E1 Interface to the System Backplane
PCM30 (E1) basic frames are 256 bits long and are transmitted at a frame repetition rate of 8000 Hz, which results in an aggregate bit rate of 256 bits x 8000/sec = 2.048Mbits/sec. The actual bit rate is 2.048Mbit/s +/-50 ppm encoded in HDB3 (High Density Bipolar 3) format. Basic frames are divided into 32 timeslots numbered 0 to 31, see Figure 6. Each timeslot is 8 bits in length and is transmitted most significant bit first (numbered bit 1). This results in a single timeslot data rate of 8 bits x 8000/sec. = 64 kbit/s. It should be noted that the Zarlink ST-BUS also has 32 channels numbered 0 to 31, but the most significant bit of an eight bit channel is numbered bit 7, see Figure 5. Therefore, ST-BUS bit 7 is synonymous with PCM30 bit 1; bit 6 with bit 2: and so on, see Zarlink Application Note MSAN-126 for more details on the ST-BUS. Tables 4 and 5 show the mapping between the ST-BUS channels and the PCM30 timeslots. When the device is in IMA (Inverse Mux for ATM) mode the mapping between the ST-BUS Channels and the PCM30 timeslots is according to Table 4. PCM30 timeslot 0 is reserved for basic frame alignment, CRC-4 multiframe alignment and the communication of maintenance information (facility data link). In most configurations timeslot 16 is reserved for either Channel Associated Signaling (CAS or ABCD bit signaling) or Common Channel Signaling (CCS). For V5.2 applications, timeslots 15, 16 and 31 may be used for CCS. The remaining timeslots are called channels and carry either PCM encoded voice signals or digital data. Channel alignment and bit numbering is consistent with timeslot alignment and bit numbering. However, channels are numbered 1 to 30 and relate to timeslots as per Table 6. PCM30 Timeslots ST-BUS Channels (DSTi/o and CSTi/o) PCM30 Timeslots ST-BUS Channels (DSTi/o and CSTi/o) 0 0 16 16 1 1 17 17 2 2 18 18 3 3 19 19 4 4 20 20 5 5 21 21 6 6 22 22 7 7 23 23 8 8 24 24 9 9 25 25 10 10 26 26 11 11 27 27 12 12 28 28 13 13 29 29 14 14 30 30 15 15 31 31
Table 4 - ST-BUS Channel vs. PCM30 Timeslot for 2.048 Mbit/s DST/CST Streams (E1)
34
SEMICMF.019
Data Sheet
MT9072
0 0 1 2 3 16 64 65 66 67 1 4 5 6 7 17 68 69 70 71 2 8 9 10 11 18 72 73 74 75 3 12 13 14 15 19 76 77 78 79 4 16 17 18 19 20 80 81 82 83 5 20 21 22 23 21 84 85 86 87 6 24 25 26 27 22 88 89 90 91 7 28 29 30 31 23 92 93 94 95 8 32 33 34 35 24 96 97 98 99 9 36 37 38 39 25 100 101 102 103 10 40 41 42 43 26 104 105 106 107 11 44 45 46 47 27 108 109 110 111 12 48 49 50 51 28 112 113 114 115 13 52 53 54 55 29 116 117 118 119 14 56 57 58 59 30 120 121 122 123 15 60 61 62 63 31 124 125 126 127
Table 5 - ST-BUS Channel vs. PCM30 Timeslot Relationship for 8.192 Mbit/s DST/CST Streams (E1)
PCM30 Timeslots ST-BUS F0/4 Chan(DSTi/o F1/5 and CSTi/o) F2/6 F3/7 PCM30 Timeslots ST-BUS F0/4 Chan(DSTi/o F1/5 and CSTi/o) F2/6 F3/7
PCM30 Timeslot PCM30 Voice/Data Channels
0 x
1 2 3...15 1 2 3...15
16 x
17 18 19...31 16 17 18...30
Table 6 - PCM30 Timeslot to PCM30 Channel Relationship (E1)
2.0 ms FRAME 15 FRAME 0
********
FRAME 14
FRAME 15
FRAME 0
TIMESLOT 0
TIMESLOT 1
****
125 s
TIMESLOT 30
TIMESLOT 31
Most Significant Bit (First)
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
BIT 8
Least Significant Bit (Last)
(8/2.048) s
Figure 6 - PCM30 Format (E1)
3.2
E1 Interface to the Physical Layer Device
Register control bits COD1-0 (address Y02) determine the format of the PCM30 transmit and receive signals. Three interface formats are provided including RZ dual rail, NRZ dual rail and NRZ single rail. RZ Dual Rail - On the Transmit side the pulse width is approximately half the duration of the PCM30 bit cell centered around the falling edge of TXCL. On the receive side RPOS and RNEG are sampled on the falling edge of EXCLi. Note that the T2OP bit in Register Y02(selectable for edge sampling) has no effect in RZ mode. NRZ Dual Rail - With this format, pulses are present for the full bit cell, which allows the set-up and hold times to be easily met. For the receiver the sampling point can be the rising edge or the falling edge of the EXCLi clock dependent on the CLKE bit in Register Y01. The transmitted data can be output either on the rising or falling edge of TXCL selected by the T2OP bit. TXCL is an input in T1 mode and output in E1 mode.
SEMICMF.019
35
MT9072
Data Sheet
NRZ Single Rail - This NRZ format is not dual rail, and therefore, only requires a single output line and a single input line (i.e., TPOS and RPOS). The T2OP bit controls the TXCL clock edge and CLKE bit controls the RPOS/RNEG sampling. HDB3 - Register Control bit THDB3 (address Y02) determines the PCM30 encoding in the transmit direction. The encoding can either be HDB3 or alternate mark inversion (AMI). The RHDB3 (address Y02) bit selects the receive HDB3 decoding.
4.0
4.1
Framing
T1 Framing
DS1 trunks contain 24 bytes of serial voice/data channels bundled with an overhead bit - the S-bit. The S-bit contains a fixed repeating pattern used to enable DS1 receivers to delineate frame boundaries. S-bits are inserted once per frame at the beginning of the transmit frame boundary. The DS1 frames are further grouped in bundles of frames, generally 12 (for D4 applications) or 24 frames deep (for ESF - extended superframe applications). The registers for controlling and observing the framing algorithms are presented in the Table 7.
36
SEMICMF.019
Data Sheet
Register Address Y00 Register Framing Mode Select Description
MT9072
This register is used for selecting the different framing modes from ESF to D4 or T1DM. The register is also used for selecting reframe criteria. This register provides the real time status of the receive framing algorithm as to basic frame synchronization and multiframe synchronization. This status register increments every 1.5 msec for D4 mode or every 3 msec for ESF mode when the basic frame synchronization is lost. This counter counts the Ft errors in ESF mode and Ft+Fs error in D4 and T1DM. This counter counts the CRC-6 errors by comparing the calculated CRC-6 with the CRC-6 bits in the ESF frame. The out of frame counter is incremeted with every loss of receive frame synchronization. The change of frame counter is incremented with every shift in the frame alignment position. This register contains latched bits for events related to framing such as framing bit errors. This counter is a latched version of Y17, the value of this counter is updated every 1 sec. This counter is a latched version of Y19, the value of this counter is updated ever 1 sec.
Y10
Synchronization and Alarm Status Word. MFOOF Counter
Y16
Y17 Y19 Y1A
Framing Bit Error Counter CRC-6 Error Counter Out of Frame Counter and Change of Frame Counter Receive Sync and Alarm Latch Framing Bit Error Count Latch CRC-6 Error Counter Latch
Y24 Y28 Y2A Y2B Y2C Y34
Out of Frame Counter Latch and This counter is a latched version of Y19, the value of this counter Change of Frame Counter Latch is updated ever 1 sec. MFOOF Counter Latch Receive Sync Interrupt Status Register Receive Sync Interrupt Status Register Mask This counter is a latched version of Y16, the value of this counter is updated ever 1 sec. This register captures interrupt events related to the receiver framer such as Framing Bit error. Interrupts can be generated by setting appropriate masks. This mask corresponds to the Y34 status register. Writing a "0" unmasks an interrupt.
Y44
Table 7 - Registers Related to Framing Mode for the MT9072 (T1)
4.1.1
T1 D4 Framing
For D4 links the S-bit position contains an alternating 101010... pattern inserted into every second S-bit. These bits are intended for determination of frame boundaries, and they are referred to as Ft bits. A separate fixed pattern, repeating every superframe, is interleaved with the Ft bits. This fixed pattern (001110) is used to delineate the 12 frame superframe. These bits are referred to as the Fs bits. In D4 frames # 6 and #12, the LSB of each channel byte may be replaced with A bit (frame #6) and B bit (frame #12) signaling information. See Table 8.
SEMICMF.019
37
MT9072
Frame # 1 2 3 4 5 6 7 8 9 10 11 12 0 0 Table 8 - D4 Superframe Structure (T1) B 1 1 0 1 1 1 A 0 0 Ft 1 0 Fs Signaling
Data Sheet
4.1.2
T1 ESF Framing
For ESF links the 6 bit framing pattern 001011, inserted into every 4th S-bit position, is used to delineate both frame and superframe boundaries. Frames #6, 12, 18 and 24 may contain the A, B, C and D signaling bits, respectively. A 4 kHz data link is embedded in the S-bit position, interleaved between the framing pattern sequence (FPS) and the transmit CRC-6 remainder (from the calculation done on the previous superframe). See Table 9.
Frame # 1 2 3 4 5 6 7 8 9 10 11
FPS
FDL X
CRC
Signaling
CB1 X 0 X CB2 X 0 X CB3 X Table 9 - ESF Superframe Structure (T1) A
38
SEMICMF.019
Data Sheet
Frame # 12 13 14 15 16 17 18 19 20 21 22 23 24 1 Table 9 - ESF Superframe Structure (T1) X D 1 X CB6 X 0 X CB5 C X FPS 1 X CB4 FDL CRC
MT9072
Signaling B
4.1.3
T1 T1DM Framing
The Ft and Fs bits are identical to the D4 format, channel 24 of each frame has a synchronization byte consisting of 10111YR0. Y is used to indicate a yellow alarm and is active low. R bit is reserved by AT&T as an 8 Kb/s communication channel. The synchronization is first declared if the Ft bit is in sync and subsequently 6 consecutive T1DM synchronization bytes are received. The synchronization error criteria for the receiver will be the same as D4.(i.e 2 out of 4,5 or 6). Although an error is detected if any of 5 synchronization bits or the Ft/Fs bits are incorrect.The OOF error selection criteria of 2 errors out of 4, 5, 6 bits is also applicable to the T1DM sync byte format; the error criteria applies to the synchronization byte and the framing bit. The received sync byte can be monitored by the status register(Y10). The Y bit an be sent by writing to control register(address Y02). The TIDMR bit can only be input from the Transmit Data Link Pin. The registers and bits used for T1DM are indicated in the register bit functions.
4.1.4
T1 G.802 Mode
G.802 mode allows interworking between an E1 and T1 system. The line is operating in T1 mode and the backplane consists of E1 data. The mapping for the backplane channels to the PCM24 side is as shown Table 10. The 193 bits from the E1 backplane stream are mapped to the 193 bits of the PCM24 side. The channel 0 and channel 16 on the backplane side are the G.704 Timeslot 0 and 16 channels and are not mapped.
SEMICMF.019
39
MT9072
DSTi/DSTo Channel#, Bit# 0 1,bit 7(MSB) 1(bit 6 to 0)-15 16 17-25 channel 16, bit 1 PCM24 bits Not mapped S-bit 119 bits Not mapped 120 to 192 193 bit Table 10 - G.802 ST-BUS to PCM24 Mapping (T1)
Data Sheet
Function Timeslot 0 S-bit
Timeslot 16
last bit
4.2
E1 Framing
The following Table shows the registers related to the E1 framing algorithm.
Register Address Y00
Register Alarm and Framing Control Register Synchronization and Alarm Status Word.
Description This is the main register for selection of the framing mode. The specific bits for control of the framer are CSYN, AUTY, CRCM, REFRM, MFRF and AUTC This register provides the real time status of receive basic frame synchronization and receive multiframe synchronization. All bits in this status register are relevant to framing except the slip bits.
Y10
Y11 Y12
CRC-4 Timers and CRC-4 Local All bits except the 2 sec timer are related to the reception of the Status CRC-4 pattern in timeslot 0. Alarm and Multiframe signaling Status NFAS and FAS Status Register Loss of basic frame synchronization counter CRC-4 Error Counter This register reports alarms such as AIS, loss of signal and Timeslot 16 and 0 remote alarms. The bits of relevance for framing are KLVE, LOSS,AIS16, AIS,RAI,RMA1 to 4, Y bit. This register shows the FAS and NFAS status such as RFA 2 to 8 and RNFA. This counter increments by one every 125 usec when the BSYNC status is set to 1. This error counter is incremented for each calculated CRC-4 submultiframe error. The CRCS1 and CRCS2 (Y11 bit 1 and 2) events increment this counter. This register reflects the FAS bit errors and a combined FAS pattern error. This register represents the latched version of framing status bits such as BSYNC. These bits are set by changes in the associated real time bits.
Y13 Y16 Y19
Y1A Y24
FAS Bit Counter and FAS Error Counter. Sync,CRC-4,MAS Latched Status Register
Y27
Performance Presistent Latched This register latches the detection of loss(LOSSP) and basic Status Register frame sync(BSYNCP). Table 11 - Registers Related to Framing for MT9072 (E1)
40
SEMICMF.019
Data Sheet
Register Address Y2A Y34 Register CRC-4 Error Counter Latch. Sync, CRC-4 Remote,Alarm,MAS and Phase Status Register Counter Indication and Counter Overflow Interrupt status Sync Interrupt Mask Register Counter Indication and Counter Overflow Interrupt Mask Register Description
MT9072
This a a sampled version of Y19 latched every one sec. These are the interrupt status bits for BSYNC, Receive Multiframe Alignment Interrupt etc. This register represents the interrupt status bits for counter overflows, counter indications etc. This is the mask register for the events in register Y34. This is the mask register for the events in register Y35
Y35 Y44 Y45
Table 11 - Registers Related to Framing for MT9072 (E1)
4.2.1
E1 Basic Framing (Timeslot 0)
Timeslot 0 of every 125us frame is reserved for basic frame alignment and contains a Frame Alignment Signal (FAS) or a Non-Frame Alignment Signal (NFAS). FAS and NFAS occur in consecutive basic frames as shown in Table 12. Bit one of the FAS can be either a CRC-4 remainder bit or an international usage bit. Bit one of the NFAS can be either a CRC-4 multiframe alignment signal, an E-bit or an international usage bit. Refer to national standards bodies for specific requirements. Bit two of the FAS and NFAS is used to distinguish between FAS (bit two = 0) and NFAS (bit two = 1) frames. Bits two to eight of the FAS are used for basic frame alignment. Basic frame alignment is initiated by a search for the bit sequence 0011011 which appears in the last seven bit positions of the FAS, see the Frame Algorithm section. Bit three of the NFAS (designated as "A"), the Remote Alarm Indication (RAI), is used to indicate the near end basic frame synchronization status to the far end of a link. Under normal operation, the A (RAI) bit should be set to 0, while in alarm condition, it is set to 1. Bits four to eight of the NFAS (i.e., Sa4-8) are additional spare bits which may be used as follows: * * * * Sa4-8 may be used in specific point-to-point applications (e.g. transcoder equipments conforming to G.761). Sa4 may be used as a message-based data link for operations, maintenance and performance monitoring. Sa5-Sa8 are for national usage but are also available from the Data link interface(TxDL,RxDL). Note that for simplicity all Sa bits including Sa4 are collectively called national bits throughout this document. See the Data Link section for accessing the national bits.
4.2.2
E1 CRC-4 Multiframing (Timeslot 0)
The primary purpose for CRC-4 multiframing is to provide a verification of the current basic frame alignment, although it can also be used for other functions such as bit error rate estimation. The CRC-4 multiframe consists of 16 basic frames numbered 0 to 15, and has a repetition rate of 16 frames X 125 microseconds/frame = 2 msec.
SEMICMF.019
41
MT9072
Data Sheet
CRC-4 multiframe alignment is based on the 001011 bit sequence, which appears in bit position one of the first six NFASs of a CRC-4 multiframe. The CRC-4 multiframe is divided into two submultiframes, numbered 1 and 2, which are each eight basic frames or 2048 bits in length.
CRC-4
CRC-4 Frame/Type 0/FAS 1/NFAS
PCM30 Channel Zero 1 C1 0 C2 0 C3 1 C4 0 C1 1 C2 1 C3 E1 C4 E2 2 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 3 0 A 0 A 0 A 0 A 0 A 0 A 0 A 0 A 4 1 Sa4 1 Sa4 1 Sa4 1 Sa4 1 Sa4 1 Sa4 1 Sa4 1 Sa4 5 1 Sa5 1 Sa5 1 Sa5 1 Sa5 1 Sa5 1 Sa5 1 Sa5 1 Sa5 6 0 Sa6 0 Sa6 0 Sa6 0 Sa6 0 Sa6 0 Sa6 0 Sa6 0 Sa6 7 1 Sa7 1 Sa7 1 Sa7 1 Sa7 1 Sa7 1 Sa7 1 Sa7 1 Sa7 8 1 Sa8 1 Sa8 1 Sa8 1 Sa8 1 Sa8 1 Sa8 1 Sa8 1 Sa8
Sub Multi Frame 1
2/FAS 3/NFAS 4/FAS 5/NFAS 6/FAS 7/NFAS 8/FAS 9/NFAS
Sub Multi Frame 2
10/FAS 11/NFAS 12/FAS 13/NFAS 14/FAS 15/NFAS
Table 12 - CRC-4 FAS and NFAS Structure (E1)
indicates position of CRC-4 multiframe alignment signal.
The CRC-4 frame alignment verification functions as follows. Initially, the CRC-4 operation must be activated and CRC-4 multiframe alignment must be achieved at both ends of the link. At the local end of a link, all the bits of every transmit submultiframe are passed through a CRC-4 polynomial (multiplied by X4 then divided by X4 + X + 1), which generates a four bit remainder. This remainder is inserted in bit position one of the four FASs of the following submultiframe before it is transmitted (see Table 12). The submultiframe is then transmitted and, at the far end, the same process occurs. That is, a CRC-4 remainder is generated for each received submultiframe. These bits are compared with the bits received in position one of the four FASs of the next received submultiframe. This process takes place in both directions of transmission. When more than 914 CRC-4 errors (out of a possible 1000) are counted in a one second interval, the framing algorithm will force a search for a new basic frame alignment if automatic CRC-4 interworking is not invoked. The result of the comparison of the received CRC-4 remainder with the locally generated remainder will be
42
SEMICMF.019
Data Sheet
MT9072
transported to the far end by the E-bits. Therefore, if E1 = 0, a CRC-4 error was discovered in a submultiframe 1 received at the far end; and if E2 = 0, a CRC-4 error was discovered in a submultiframe 2 received at the far end. No submultiframe sequence numbers or re-transmission capabilities are supported with layer 1 PCM30 protocol. See ITU-T G.704 and G.706 for more details on the operation of CRC-4 and E-bits.
4.2.2.1
E1 Automatic CRC-4 Interworking
When control bit AUTC (register address Y00) is set to zero, the MT9072 framing algorithm supports automatic interworking of interfaces with and without CRC-4 processing capabilities. That is, if an interface with CRC-4 capability, achieves valid basic frame alignment, but does not achieve CRC-4 multiframe alignment by the end of a predefined period, the distant end is considered to be a non-CRC-4 interface. When the distant end is a non-CRC4 interface, the near end automatically suspends receive CRC-4 functions, continues to transmit CRC-4 data to the distant end with its E-bits set to zero, and provides a status indication. Naturally, if the distant end initially achieves CRC-4 synchronization, CRC-4 processing will be carried out by both ends. When control bit AUTC is one, Automatic CRC-4 Interworking is deactivated. In this case, if the Automatic Remote Alarm Indication (RAI) Operation (ARAI) control bit (register address Y00) is low, and if CRC-4 multiframe alignment is not found in 400 msec, then the transmit Remote Alarm Indication (RAI) (bit 3 (A) of the transmit NFAS) will be continuously high until CRC-4 multiframe alignment is achieved. The TE control bit (register address Y00) for transmit E bits will have the same function in both states of AUTC. That is, when CRC-4 synchronization is not achieved the state of the transmit E-bits will be the same as the state of the TE control bit. When CRC-4 synchronization is achieved the transmit E-bits will function as per ITU-T G.704 as described in the previous section. Table 13 outlines the operation of the AUTC, ARAI and TALM control bits of the MT9072.
AUTC 0
ARAI 0
TALM X
Description Automatic CRC-interworking is activated. If no valid CRC MFAS is being received, transmit RAI will flicker high with every reframe (8msec.), this cycle will continue for 400 msec., then transmit RAI will be low continuously. The device will stop searching for CRC MFAS, continue to transmit CRC-4 remainders, stop CRC-4 processing, indicate CRC-to-non-CRC operation and transmit E-bits to be the same state as the TE control bit (control register address Y00). Automatic CRC-interworking is activated. Transmit RAI is low continuously. Automatic CRC-interworking is activated. Transmit RAI is high continuously. Automatic RAI is activated. Automatic CRC-interworking is de-activated. If no valid CRC MFAS is being received, transmit RAI flickers high with every reframe (8 msec.), this cycle continues for 400 msec, then transmit RAI becomes high continuously. The device continues to search for CRC MFAS and transmit E-bits are the same state as the TE control bit. When CSYN = 0, the CRC MFAS search is terminated and the transmit RAI goes low. Automatic RAI is activated. Automatic CRC-interworking is de-activated. Transmit RAI is low continuously. Automatic RAI is activated. Automatic CRC-interworking is de-activated. Transmit RAI is high continuously.
0 0 1
1 1 0
0 1 X
1 1
1 1
0 1
Table 13 - Operation of AUTC, ARAI and TALM Control Bits (E1)
SEMICMF.019
43
MT9072
4.2.3 E1 Channel Associated Signaling (CAS) Multiframing (Timeslot 16)
Refer to the section on Channel Associated Signaling (CAS) Operation.
Data Sheet
4.2.4
E1 Framing Algorithm
The MT9072 contains three distinct framing algorithms: basic frame alignment, signaling multiframe alignment and CRC-4 multiframe alignment. Figure 7 is a state diagram that illustrates these algorithms and how they interact. After power-up, the basic frame alignment framer will search for a frame alignment signal (FAS) in the PCM30 receive bit stream. Once the FAS is detected, the corresponding bit 2 of the non-frame alignment signal (NFAS) is checked. If bit 2 of the NFAS is zero a new search for basic frame alignment is initiated. If bit 2 of the NFAS is one and the next FAS is correct, the algorithm declares that basic frame synchronization has been found (status register address Y10 bit BSYNC is reset to zero). Once basic frame alignment is acquired the signaling and CRC-4 multiframe searches will be initiated. The signaling multiframe algorithm will align to the first multiframe alignment signal pattern (MFAS = 0000) it receives in the most significant nibble of channel 16 (status register address Y10 bit MSYNC is zero). Signaling multiframe alignment will be lost when two consecutive multiframes are received in error. The CRC-4 multiframe alignment signal is a 001011 bit sequence that appears in PCM30 bit position one of the NFAS in frames 1, 3, 5, 7, 9 and 11 (see Table 12). In order to achieved CRC-4 synchronization two consecutive CRC-4 multiframe alignment signals must be received without error (status register address Y10 bit CSYNC is zero). The MT9072 framing algorithm supports automatic interworking of interfaces with and without CRC-4 processing capabilities. That is, if an interface with CRC-4 capability, achieves valid basic frame alignment, but does not achieve CRC-4 multiframe alignment by the end of a predefined period, the distant end is considered to be a non-CRC-4 interface. When the distant end is a non-CRC-4 interface, the near end automatically suspends receive CRC-4 functions, continues to transmit CRC-4 data to the distant end with its E-bits set to zero, and provides a status indication. Naturally, if the distant end initially achieves CRC-4 synchronization, CRC-4 processing will be carried out by both ends. This feature is selected when control bit AUTC (control register address Y00) is set to zero.
4.2.4.1
Notes for Synchronization State Diagram (Figure 7)
1) The basic frame alignment, signaling multiframe alignment, and CRC-4 multiframe alignment functions operate in parallel and are independent. 2) The receive channel associated signaling bits and signaling multiframe alignment bit will be frozen when multiframe alignment is lost. 3) Manual re-framing of the receive basic frame alignment and signaling multiframe alignment functions can be performed at any time. 4) The transmit RAI bit will be one until basic frame alignment is established, then it will be zero. 5) E-bits can be optionally set to zero until the equipment interworking relationship is established. When this has been determined one of the following will take place: a) CRC-to-non-CRC operation - E-bits = 0, b) CRC-to-CRC operation - E-bits as per G.704 and I.431. 6) All manual re-frames and new basic frame alignment searches start after the current frame alignment signal position. 7) After basic frame alignment has been achieved, loss of frame alignment will occur any time three consecutive incorrect basic frame alignment signals are received. Loss of basic frame alignment will reset the complete framing algorithm.
44
SEMICMF.019
Data Sheet
MT9072
8) When CRC-4 multiframe alignment has been achieved, the primary basic frame alignment and resulting multiframe alignment will be adjusted to the basic frame alignment determined during CRC-4 synchronization. Therefore, the primary basic frame alignment will not be updated during the CRC-4 multiframe alignment search, but will be updated when the CRC-4 multiframe alignment search is complete.
Out of synchronization YES Search for primary basic frame alignment signal RAI=1, Es=0. >914 CRC errors in one second YES NO Verify Bit 2 of non-frame alignment signal. YES No CRC multiframe alignment. 8 msec. timer expired* Verify second occurrence of frame alignment signal. YES CRC-4 multi-frame alignment Start 400 msec timer. Note 7. Primary basic frame synchronization acquired. Enable traffic RAI=0, E's=0. Start loss of primary basic frame alignment checking. Notes 7 & 8. signaling multi-frame alignment Search for multiframe alignment signal. Note 7. YES Multiframe synchronization acquired as per G.732. Note 7. NO Find two CRC frame alignment signals. Note 7. CRC multiframe alignment No CRC multiframe alignment. 8 msec. timer expired** YES Check for two consecutive errored multiframe alignment signals. Notes 7 & 8. NO 3 consecutive incorrect frame alignment signals NO
NO Start 8 msec timer. Note 7. RAI = 0 Basic frame alignment acquired
CRC-to-CRC interworking. Re-align to new basic frame alignment. Start CRC-4 processing. E-bits set as per G.704 and I.431. Indicate CRC synchronization achieved. Notes 7 & 8.
Parallel search for new basic frame alignment signal. Notes 6 & 7. 400 msec timer expired CRC-to-non-CRC interworking. Maintain primary basic frame alignment. Continue to send CRC-4 data, but stop CRC processing. E-bits set to `0'. Indicate CRC-to-non-CRC operation. Note 7.
* only if CRC-4 synchronization is selected and automatic CRC-4 interworking is de-selected. ** only if automatic CRC-4 interworking is selected.
Figure 7 - Synchronization State Diagram (E1)
SEMICMF.019
45
MT9072
5.0 Elastic Buffer
Data Sheet
The MT9072 has a two frame receive elastic (or slip) buffer, which absorbs wander and low frequency jitter in multitrunk applications. If desired, the elastic buffer can be bypassed by using the Data Link RxDL pin output (see the following section). The received data (RPOS and RNEG) is clocked into the elastic buffer with the extracted (EXCLi pin) clock and is clocked out of the elastic buffer with the system (CKi pin) clock. The EXCLi clock is generated from the receive data, and is therefore phase-locked with that data. In normal operation, the EXCLi clock will be phaselocked to the CKi clock by an external phase locked loop (PLL). Therefore, in a single trunk system, the receive data is in phase with the EXCLi clock, the CKi clock is phase-locked to the EXCLi clock, and the read and write positions of the elastic buffer will remain fixed with respect to each other. In a multi-trunk slave or loop-timed system (i.e., PABX application) a single trunk will be chosen as a network synchronizer, which will function as described in the previous paragraph. The remaining trunks will use the system timing derived from the synchronizer to clock data out of their slip buffers. Even though the signals from the network are synchronous to each other, due to multiplexing, transmission impairments and route diversity, these signals may jitter or wander with respect to the synchronizing trunk signal. Therefore, the EXCLi clocks of non-synchronizer trunks may wander with respect to the EXCLi clock of the synchronizer and the system bus. Network standards state that, within limits, trunk interfaces must be able to receive error-free data in the presence of jitter and wander (refer to network requirements for jitter and wander tolerance). The MT9072 will allow a maximum of 26 channels (208 UI, unit intervals) of wander and low frequency jitter before a frame slip will occur. The minimum delay through the receive slip buffer is approximately two channels and the maximum delay is approximately 60 channels (see Figure 8). When the CKi and the EXCLi clocks are not phase-locked, the rate at which data is being written into the slip buffer from the line side may differ from the rate at which it is being read out onto the ST-BUS. If this situation persists, the delay limits stated in the previous paragraph will be violated and the slip buffer will perform a controlled frame slip. That is, the buffer pointers will be automatically adjusted so that a full frame is either repeated or lost. All frame slips occur on frame boundaries. Two status bits, RSLP and RSLPD (register address Y10 for E1 and Y13 for T1), give indication of a slip occurrence and direction. RSLP changes state in the event of a slip. If RSLPD=0, the slip buffer has overflowed and a frame was lost; if RSLPD=1, a underflow condition occurred and a frame was repeated. A maskable interrupt status bit RSLIPI (register address Y34 for E1 and Y36 for T1) is also provided. Figure 8 illustrates the relationship between the read and write pointers of the receive slip buffer. Measuring clockwise from the write pointer, if the read pointer comes within two channels of the write pointer a frame slip will occur, which will put the read pointer 34 channels from the write pointer. Conversely, if the read pointer moves more than 60 channels from the write pointer, a slip will occur, which will put the read pointer 28 channels from the write pointer. This provides a worst case hysteresis of 13 channels peak (26 channels peak-to-peak) or a wander tolerance of 208 UI. The registers relevant to controlling and observing the elastic buffer in T1 mode are shown in Table 14. The registers related to elastic buffer for E1 are shown in Table 15.
46
SEMICMF.019
Data Sheet
Read Pointer 60 CH Write Pointer Read Pointer
MT9072
2 CH
13 CH Wander Tolerance
47 CH
512 Bit Elastic Store
15 CH
34 CH Read Pointer
28 CH Read Pointer
-13 CH
Figure 8 - Read and Write Pointers in the Slip Buffers In T1 mode, the transmit and receive elastic buffers also serve the purpose of rate conversion between the 1.544 Mbit/s line rate and the 2.048 Mbit/s backplane rate. Consequently, in T1 mode the elastic buffers cannot be bypassed, except for the special case of T1 IMA mode.
Register Address Y00 Y13
Register Framing Mode Select Receive Slip Buffer Status Word
26 Channels
Description If IMA mode is selected the transmit and receive elastic buffers are bypassed. This register provides status bits for receive slip and its direction word that indicates the phase difference between the ST-BUS and the PCM24
Y14
Transmit Slip Buffer Status Word This register provides status bit for transmit slip and its direction word that indicates the phase difference between the ST-BUS and the PCM24. Elastic Store and Excessive Zero This register indicates the latched version of the slip indicator Status Latch bits from registers Y13 and Y14. Elastic Store and Excessive Zero Interrupt status word for the slip indicators. Interrupt Status Elastic Store and Excessive Zero Interrupt mask bits for the slip indicators. Interrupt Mask Transmit Set Delay Bits This register sets a one time delay through the transmit slip buffer.
Y26 Y36 Y46 YF7
Table 14 - Registers Related to the Elastic Buffer (T1)
SEMICMF.019
47
MT9072
Register Address Y00 Y03 Y10 Y14 Y34 Y44 Register Framing Mode Select DL,CCS,CAS and Other Control Register Sync and CRC-4 Remote status Phase Status Indicator Sync,CRC-4 Remote, Alarm, MAS and Phase Status Word Sync,CRC-4 Remote, Alarm, MAS and Phase Status Word Interrupt Mask Description
Data Sheet
If IMA mode is selected the receive elastic buffers are bypassed. ELAS bit is used to bypass the elastic store, that data at DSTo is the received. PCM30 data after the HDB3 coding. RSLP and RSLPD show the slip and the direction of the slip. This word reflects the delay through the receive elastic store from the line to the ST-BUS side. RSLIPI in this register reflects the interrupt due to a slip. Interrupt mask bits for the slip indicator.
Table 15 - Registers Related to Elastic Store (E1)
5.1
Transmit Elastic Buffer
In T1 mode, the MT9072 contains a transmit elastic buffer in addition to the receive elastic buffer. Data is clocked into the transmit elastic buffer by the 2.048 Mbit/s or 8.192 Mbit/s ST-BUS clock (which is subsequently divided to a 2.048MHz clock). The data is clocked out of the transmit elastic buffer by the 1.544MHz clock input to the TXCL pin. The delay through the transmit elastic buffer will vary in accordance with the position of the channel in the frame. For example, PCM24 channel 1 sits in the elastic buffer for approximately 1 usec, and PCM24 channel 24 sits in the elastic buffer for approximately 32 usec. The relative phase delay between the system ST-BUS frame boundary and the transmit elastic frame read boundary is measured every frame and reported in the Transmit Slip Buffer Status Word (Y14). In addition, the relative delay between these frame boundaries may be programmed by writing to Tx Set Delay Bits (register address YF7). Every write to the TX Set Delay Bits resets the Transmit Slip Buffer MSB bit TxSBMSB (register address Y14). After a write, the delay through the slip buffer is less than 1 frame in duration. Each write operation will result in a disturbance of the transmit PCM24 frame boundary, causing the far end to go out of sync. The transmit elastic buffer is capable of performing controlled slips in a manner similar to the receive elastic buffer. Slips on the transmit side are independent of slips on the receive side. The two status bits. TSLIP and TSLPD (register address Y14), give indication of a slip occurrence and direction. TSLP changes state in the event of a slip. If TSLPD=0, the slip buffer has overflowed and a frame was lost; if TSLPD=1, an underflow condition occurred and a frame was repeated. A maskable interrupt status bit TXSLIPI (register address Y36) is also provided. Under normal operation no slips should occur in the transmit path. Slips will only occur if the input CKi clock has excess wander relative to the input TXCL clock, or if the TX Set Delay Bits (register address YF7) register is initialized too close to the slip pointers after system initialization.
48
SEMICMF.019
Data Sheet
6.0
6.1
MT9072
Data Link
T1 Data Link
The ESF protocol allows for carrier messages to be embedded in the S-bit position. The MT9072 provides 3 separate means of controlling the Data Link. Transmit and receive Data Link pins TxDL, TxDLC, RxDL and RxDLC. Bit - Oriented Messages may be transmit and received via dedicated transmit and receive registers(Y07,Y08,Y12). This is only applicable in the ESF mode. * The ESF Data Link (DL) can be connected to an internal HDLC, operating at a bit rate of 4 kbits/sec. The HDLC can be activated by setting the control bit 1(HDLCEn) of the HDLC & Data Link Control Word (Y06). In the D4 mode the Fs bits can be inserted/extracted from the Data Link pins by setting the EDLEN bit in Y06. The registers related to the Data Link are shown in Table 16. * *
Register Address Y06
Register HDLC and Data Link Control Register
Description This register determines the source of the Data Link which can be the HDLC, Bit Oriented messages or the external Data Link. This register also controls the type of clocks provided to the external Data Link interface.
Y07 Y08 Y12 Y25 Y35 Y45
Transmit bit Oriented Message This register holds the message that will be sent in ESF FDL if the BOMEN bit in Y06 is set. Receive bit Oriented Message Match Receive bit Oriented Message This register is the match register for received bit oriented message This register holds the value of the receive bit oriented message
Receive Line Status and Timer This register contains bit oriented message and bit oriented Latch message match latch bits. Receive Line and Timer Interrupt Status Receive Line and Timer Interrupt Mask This register contains bit oriented message and bit oriented message match interrupt status bits. These are the mask bits for Y35.
Table 16 - Registers Related to the Data Link and Bit Oriented Messages (T1)
6.1.1
T1 Data Link (DL) Pin Access
When EDLEN(Y06) is set to "1" the data link (DL) bits can be sourced/sinked to and from the TxDL and RxDL pins, by enabling the corresponding pulses in either gapped clocks or enable low signals provided at the RxDLC and TxDLC pins. The option of either gapped clock or enable signal is selected by control bit DLCK (Register address Y06). In D4 or ESF mode, the optional serial data link operates at 4 khz. In D4 mode the data link pins are used to send/receive Fs bits only, while the Ft bits are generated internally. See Figures 40 to 43.
6.1.1.1
T1 Data Link (DL) Pin Data Received from PCM24
The RxDLC clock is derived from the receive extracted clock (EXCLi).The B8ZS decoded receive data, at 1.544Mbit/s, is clocked out of the device on the RxDL pin with the rising edge of EXCLi and is aligned to RXDLC. In order to facilitate the attachment of this data stream to a Data Link controller, the clock signal RxDLC (falling edge
SEMICMF.019
49
MT9072
Data Sheet
of EXCLi) consists of positive pulses, of nominal width of 344 ns, during the Fs bit cell times that are selected for the Data Link, with the rising edge aligned with the middle of the bit cell. DL data will not be lost or repeated when a receive frame slip occurs as the DL data does not pass through the elastic buffer. See Figures 42 to 43 for timing requirements.
6.1.1.2
T1 Data Link (DL) Pin Data Sent to PCM24
The TxDLC clock is derived from the transmit clock (TXCL) and is provided one frame before its usage on the appropriate S-bit. Hence the TXDLC clock is provided one frame before it is used in ESF Mode in Frames 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24. See Figures 40 to 41 for timing requirements
6.2
E1 Data Link (DL) Operation
Table 12 shows the contents of the transmit and receive Frame Alignment Signals (FAS) and Non-frame Alignment Signals (NFAS) of timeslot zero of a PCM30 signal. Even numbered frames (CRC Frame # 0, 2, 4,...) are FASs and odd numbered frames (CRC Frame # 1, 3, 5,...) are NFASs. The bits of each channel are numbered 1 to 8, with bit 1 being the most significant and bit 8 the least significant. The Data Link (DL) bits, also referred to as National bits, are the Sa4, Sa5, Sa6, Sa7 and Sa8 bits of the PCM30 timeslot zero NFAS frames. Any number and combination of these bits may be used for the transport of maintenance and performance monitoring information across the PCM30 link. The DataLink in controlled by the address Y06 and Y08. The received Data Link bits are always sent to the DataLink Pins and the National bit buffers(YC0-YC4) The Data Link (DL) bits (Sa4~Sa8) of the PCM30 timeslot zero NFAS frames can be accessed by the MT9072 in the following four ways: External serial port pins. Hence the user can use pins (TxDL and TxDLC) for transmit data link access and RxDL and RXDLC for receive data link access. * Micro port access which would use Transmit 5 bit register (TNU4-8 address YB0 to YB4). For the receiver Receive 5 bit register (RNU4-8 address YC0-YC4). * ST-BUS access Transmit ST-BUS (DSTi timeslot 0) enabled by transparent mode. * On board HDLC for Timeslot 0. Note: that the user can source different Sa bits from a combination of the above 4 methods. For instance the Sa4 bit could be sourced from the External Serial Port and Sa5 to Sa8 from the micro port register (TNU5-8 address YB1 to YB4). The registers related to the configuration control and status of the data link are shown in Table 17. *
Register Address Y00 Y06 Y08
Register Alarm and Framing Control Register HDLC and CCS ST-BUS control register Data Link Control Register
Description The Data Link is not supported in the IMA mode. The bit HPSEL has to be 0 if the internal HDLC is to be used for the Data Link. This register determines the source of the Sa bits which can be micro port,HDLC, data link pins or ST-BUS. This register is also used to control the data link pins Txdl and Rxdl. The national use bits RNU can be read from this status register. The Sa bit latched values can be read from this register, SA5VL, SA6NL etc.
Y13 Y26
NFAS and FAS status CAS, National, CRC-4 Latched Status
Table 17 - Data Link and Sa bits Configuration and Status Registers (E1)
50
SEMICMF.019
Data Sheet
Register Address Y36 Y46 Register CAS, National, CRC-4 Interrupt Status CAS, National, CRC-4 Interrupt Mask Description
MT9072
The Sa bit interrupt values can be read from this register, SA5VI, SA6NI etc. These are the mask bits for Y36. Transmit national bits used for sending Sa bits(SA4 to SA8). Receive National bits(SA4 to SA8)
YB0-YB4 Transmit National Bits YC0-YC4 Receive national bit
Table 17 - Data Link and Sa bits Configuration and Status Registers (E1)
6.2.1
E1 Data Link (DL) Pin Access
The pin (TxDL, TxDLC, RxDL and RxDLC) enable bits Sa4SS to Sa8SS of control register address Y08 determine the type of data link access enabled. A '01' code enables the corresponding data link (DL) bits to be sourced to and from the RxDL and TxDL pins, by enabling the corresponding pulses in either gapped clocks or enable low signals provided at the RxDLC and TxDLC pins. The option of either gapped clock or enable signal is selected by control bit DLCK (register address Y08). The data link bits are transmitted on and received from the PCM30 link, in the national bit (Sa4 to Sa8) positions (four to eight of timeslot zero) of the Non-Frame Alignment Signal (NFAS) frames. The gapped clock rate will be either 4, 8, 12, 16 or 20kb/s, and will depend on the number of Sa bits enabled by SA#SS bits (register Y08). Similarly the enable pulse width(s) will also depend on the number of Sa bits enabled.
6.2.1.1
E1 Data Link (DL) Pin Data Transmitted on PCM30
Data to be transmitted onto the line in the Sa bit position is clocked in from the TxDL pin with the TxDLC clock. Although the aggregate clock rate equals the bit rate, it has a nominal pulse width of 244 ns, and it clocks in the TxDL as if it were a 2.048Mbit/s data stream. The clock can only be active during bit times 4 to 0 of the ST-BUS frame. The TxDL input signal is clocked into the MT9072 by the falling edge of TxDLC which occurs about 3/4 into the ST-BUS bit cell. If DL bits are selected to be accessed through the DL pins, then all other programmed functions for those Sa bit positions are overridden. See Figures 59 & 60 for timing requirements.
6.2.1.2
E1 Data Link (DL) Pin Data Received on PCM30 - With No Elastic Buffer
The RxDLC clock and enable signal is derived from the receive extracted clock (EXCLi) and is aligned with the receive data link output RxDL. The HDB3 decoded receive data, at 2.048Mbit/s, is clocked out of the device on the RxDL pin with the falling edge of EXCLi. In order to facilitate the attachment of this data stream to a Data Link controller, the clock signal RxDLC consists of positive pulses, of nominal width of 244 ns, during the Sa bit cell times that are selected for the data link, with the rising edge aligned with the middle of the bit cell. No DL data will be lost or repeated when a receive frame slip occurs as the DL data does not pass through the elastic buffer. The output signal at the RxDLC pin may be either a clock or an enable signal as programmed by the DLCK control bit (register address Y08). See Figures 62 & 63 for timing requirements.
6.2.1.3
E1 Data Link (DL) Pin Data Received on PCM30 - With Elastic Buffer
In this case, the TxDLC pin is used for both DL data transmitted on the PCM30 link and DL data received on the PCM30 link. However, instead of using the non-buffered data output at the RxDL pin, the buffered DSTo output data is used. The clock at the TxDLC pin clocks data from the DSTo ST-BUS stream into an external controller, or the enable signal at the TxDLC pin enables a 2.048Mbit/s clock which clocks data from the DSTo ST-BUS stream into an external controller. Since a common clock is used for both transmit and receive, a simpler data controller may be used such as the MT8952B. However, DL data will be lost or repeated when a receive frame slip occurs, as the DL data does pass through the elastic buffer. See Figures 59 - 60 for timing requirements.
SEMICMF.019
51
MT9072
6.2.2 E1 Data Link (DL) National Bit Buffer Access
Data Sheet
When the National Bit Buffer transmit data registers access is enabled, the settings of 40 data bits in 5 registers (address YB0-YB4) determine the Data Link (DL) output on the PCM30 link corresponding to bit positions Sa4-8 over one complete CRC-4 Multiframe. The CRC-4 alignment status bit CALN (register address Y11) and corresponding maskable interrupt status bit CALNI (register address Y36) indicate the beginning of every received CRC-4 multiframe. Data for DL transmission should be written to the National Bit Buffer transmit data registers immediately following the CALN status indication (during basic frame 0) and before the start of basic frame 1. Table 18 illustrates the organization of the MT9072 transmit and receive national bit buffers. Each row is an addressable byte of the MT9072 national bit buffer, and each column contains the national bits of an odd numbered frame of each CRC-4 Multiframe. The transmit and receive national bit buffers are located at addresses YB0 to YB4 and YC0 to YC4 respectively.
Addressable Bytes Transmit TN0 TN1 TN2 TN3 TN4 Address YB0 YB1 YB2 YB3 YB4 Receive RN0 RN1 RN2 RN3 RN4 Address YC0 YC1 YC2 YC3 YC4 F1 B7
Sa4 Sa5 Sa6 Sa7 Sa8
NFAS Frames of a CRC-4 Multiframe F3 B6
Sa4 Sa5 Sa6 Sa7 Sa8
F5 B5
Sa4 Sa5 Sa6 Sa7 Sa8
F7 B4
Sa4 Sa5 Sa6 Sa7 Sa8
F9 B3
Sa4 Sa5 Sa6 Sa7 Sa8
F11 B2
Sa4 Sa5 Sa6 Sa7 Sa8
F13 B1
Sa4 Sa5 Sa6 Sa7 Sa8
F15 B0
Sa4 Sa5 Sa6 Sa7 Sa8
Table 18 - MT9072 National Bit Buffers (E1) For the National Bit Buffer transmit registers DL access to be enabled the SA4SS to SA8SS(register Y08) are set to 00. Similarly, the DL data received on the PCM30 link is output to the National Bit Buffer receive data registers (register address YC0-YC4), corresponding to bit positions as shown in Table 18. However, the National Bit Buffer receive data registers are always enabled, regardless of the above control bit settings(SA4SS to SA8SS). Received DL Data should be read from the National Bit Buffer receive data registers immediately following the CALN status indication (during basic frame 0) and before the start of basic frame 1. In order to facilitate conformance to ETS 300 233, three maskable interrupts are available for change of state of Sa bits in the receive National Bit Buffer. These include Eight Consecutive Sa6 Nibbles (Sa6N8), Sa6 Nibble Change (Sa6N) and Sa Nibble Change (SaN). See the detailed descriptions for these status bits provided in the CAS, National, CRC-4 Local and Timer Interrupt Status Register (address Y36).
6.2.3
E1 Data Link (DL) ST-BUS Access
When the ST-BUS Data Link (DL) access is enabled, the setting of the 8 ST-BUS DSTi data bits determine the Data Link (DL) output on the PCM30 link corresponding to bit positions one to three and Sa4-8 over each Non-Frame Alignment Signal (NFAS) frame. Data for DL transmission should be written to DSTi immediately following the NFAS frame (during FAS frames) and before the start of the next NFAS frame. The ST-BUS Data Link (DL) access is enabled if the Sa Source Select Bits (Sa4SS-SA8SS) are set to '10' in register Y08. ST-BUS DSTi timeslot 0 bits will be transmitted as NFAS bits on the PCM30 link, as shown in Table 19 (bit positions one to eight of timeslot zero, of odd CRC-4 frames 1, 3, 5, 7, 9, 11, 13, 15). The DL data received on the PCM30 link is always output to ST-BUS DSTo timeslot 0 during NFAS frames, regardless of the settings of SA4SS to SA8SS.
52
SEMICMF.019
Data Sheet
ST-BUS DSTi CRC-4 Frame All NFAS Timeslot n Data Bits (B7-B0) P1, P2, P3, Sa4, Sa5, Sa6, Sa7, Sa8 Timeslot 0 PCM30 Transmit CRC-4 Frame All NFAS
MT9072
Data Bits (B1-B8) P1, P2, P3, Sa4, Sa5, Sa6, Sa7, Sa8
Note 1. For 2.048Mbit/s operation, n=0. Note 2. For 8.192Mbit/s operation, n =0,1,2,3 where n corresponds to the framer number (i.e. n=0=framer 0... n=3= framer 3). Note 3. To source the NFAS, Sa bits from DSTi, ST-BUS mode access must be enabled (SA4SS to SA8SS = 10 register address Y08.
Table 19 - Transmit PCM30 National Bits from ST-BUS 2.048Mbit/s or 8.192Mbit/s DSTi (E1)
6.2.4
E1 Timeslot 0 CRC-4 NFAS Receive from PCM30 to DSTo
Non-Frame Alignment Signal (NFAS) bits on the receive PCM30 link (bit positions one to eight of timeslot 0 of odd CRC-4 frames 1, 3, 5, 7, 9, 11, 13, 15) are sourced to the ST-BUS DSTo stream.The data to DSTo is mapped unaltered from the receive PCM30 link as shown in Table 20. ST-BUS DSTo CRC-4 Frame All NFAS
Note Note Note Note 1. 2. 3. 4. For For For For
PCM30 Receive Timeslot 0 CRC-4 Frame All NFAS Data Bits (B1-B8) P1, P2, P3, Sa4, Sa5, Sa6, Sa7, Sa8
Timeslot n
Data Bits (B7-B0) P1, P2, P3, Sa4, Sa5, Sa6, Sa7, Sa8
2.048Mbit/s operation, n=0. 8.192Mbit/s operation, n =0,1,2,3 where n corresponds to the framer number (i.e. n=0=framer 0... n=3= framer 3). these functions to be valid, NFAS DSTi ST-BUS mode access must be enabled (SA4SS to SA8SS register address Y08). these functions to be valid, the Timeslot Control Registers must be disabled (all bits=0 register address Y90-YAF).
Table 20 - Receive PCM30 National Bits to ST-BUS 2.048Mbit/s or 8.192Mbit/s DSTo (E1)
6.3
T1 Bit Oriented Message
Bit Oriented Messages can be sent on the FDL in ESF mode. Bit - Oriented Messages may be transmitted via the TxBOM register (Y07) and received in the RxBOM (Y12). Transmission is enabled by setting bit 2 - BOMEn in the HDLC &Data link Control Word(Y06). Bit - oriented messages may be periodically interrupted (up to once per second) for a duration of up to 100 milliseconds. This is to accommodate bursts of message - oriented protocols. Table 21 shows the messages that can be sent and received according to T1.403. The transmit data link will contain the repeating serial data stream 111111110xxxxxx0 where the byte 0xxxxxx0 originates from the user programmed register "Transmit Bit Oriented Message" - Y07. The receive BOM register "Receive Bit Oriented Message" - Y12, will contain the last received valid message (the 0xxxxxx0 portion of the incoming serial bit stream). To prevent spurious inputs from creating false messages, a new message must be present in 8 of the last 10 appropriate byte positions before being loaded into the receive BOM register. When a new message has been received, a maskable interrupt (maskable by setting bit 4 low in Receive Line status and Timer Mask (Y45) may occur. Bit oriented messages are only applicable in the ESF mode. A Bit oriented match register is available RXBOMM(Y08) and a maskable interrupt can be generated when the received Bit Oriented Message matches the contents of RXBOMM; the mask can be enabled by writing a `0' to bit
SEMICMF.019
53
MT9072
3 of the Receive Line and Timer Interrupt Mask Register (Y45). Octet # 1 2 8 F S 7 L A 6 A P 5 G I C/R EA 4 3 2 1
Data Sheet
Octet Content 01111110 00111000 or 00111010 00000001 00000011
3 4 5 6 7 8 9 10 11 12 13 14
T C G3 FE G3 FE G3 FE G3 FE F
E O LV SE LV SE LV SE LV SE C
I N G4 LB G4 LB G4 LB G4 LB S T U1 G1 U1 G1 U1 G1 U1 G1 R U2 R U2 R U2 R U2 R O G5 G2 G5 G2 G5 G2 G5 G2 L SL Nm SL Nm SL Nm SL Nm
EA
G6 NI G6 NI G6 NI G6 NI
t0 t0 t0-1 t0-1 t0-2 t0-2 t0-3 t0-3 Frame Check Sequence
Table 21 - T1.403 and T1.408 Message Oriented Performance Report Structure (T1)
Note:
ADDRESS
00111000
INTERPRETATION
SAPI = 14, C/R = 0 (CI) EA = 0
00111010 00000001 CONTROL
00000011
SAPI = 14, C/R = 1(Carrier) EA = 0 TEI = 0, EA =1 INTERPRETATION
Unacknowledged Information Transfer
ONE SECOND REPORT
G1 = 1
INTERPRETATION
CRC Error Event =1
G2 =1 G3 =1 G4 =1 G5 =1 G6 =1 SE = 1 FE = 1 LV = 1 SL = 1 LB = 1 U1,U2 = 0 R=0
1 < CRC Error Event < 5 5 < CRC Error Event < 10 10 < CRC Error Event < 100 100 < CRC Error Event < 319 CRC Error Event > 320 Severely - Errored Framing Event >=1 Frame Synchronization Bit Error Event >=1 Line code Violation Event >=1 Slip Event >=1 Payload Loopback Activated Under Study for sync. Reserved - set to 0
54
SEMICMF.019
Data Sheet
NmNI = 00, 01, 10, 11 FCS VARIABLE INTERPRETATION CRC16 Frame Check Sequence One Second Module 4 counter
MT9072
7.0
7.1 7.1.1
Signaling
T1 Signaling T1 Robbed Bit Signaling
When global control bit RBEn (Y04, Bit 8) is high the MT9072 will insert ABCD or AB signaling bits into bit 8 of every transmit DS0 every 6th frame if the corresponding per channel Clear Channel bit(CC) is turned off. For the transmitter Robbed bit signaling can be turned off on a per channel basis by setting CC bit in per timeslot control register(Y90-YAF). The AB or ABCD signaling bits from received frames 6 and 12 (AB) or from frames 6, 12, 18 and 24 (ABCD) will be loaded into an internal storage RAM. The transmit AB/ ABCD signaling nibbles can be set either via the microport or through related channels of the CSTi serial links, see ST-BUS vs. PCM24 Channel Relationship in Tables 1 to 2. If the MPST bit is set in the Per Timeslot Control register(Y90-YAF), the transmit signaling is sourced from the microport and not updated from the CSTi channel. If the MPST bit is not set, any values written to the transmit signaling memory will be overwritten by the CSTi stream. The receive signaling bits are stored in an internal RAM. These bits can be sourced to the CSTo streams. The serial control streams that contain the transmit / receive signaling information (CSTi and CSTo respectively) can be clocked at 2.048 MHz, or 8.192 MHz(global control0 register 900). In the case of 8.192 MHz the signaling from framers 0 to 3 are sent and received by CSTi0/CSTo0 and framer 4 to 7 are sent and received on CSTi4/CSTo4. The selection of the CSTi/CSTo interface is done by the number of signaling channels to be transmitted / received = 24 (timeslots) x 4 bits per timeslot (ABCD) = 24 nibbles. This leaves many unused nibble positions in the 2.048 MHz CSTi / CSTo bandwidth. These unused nibble locations are tristated. The usage of the bit stream is as follows: the signaling bits are inserted / reported in the same CSTi / CSTo channels that correspond to the DS1 channels used in DSTi / DSTo - see Table 1 to 2. The ABCD are in the least significant nibble of each channel. Unused nibbles and timeslots are tristate. In order to facilitate multiplexing on the CSTo control stream, an additional control bit CSToEn (bit 1 of the interrupt and IO Control Word YF1) will tristate the whole stream when set low. This control bit is forced low when the reset pin is asserted. In the case of D4 trunks, only AB bits are reported. The control bits SM1-0(Register Y04) allow the user to program the 2 unused bits reported on CSTo in the signaling nibble(for D4 Mode) otherwise occupied by CD signaling bits in ESF trunks. A receive signaling bit debounce of 6 msec can be selected (RSDB set high - bit 6 of the signaling Control Word Y04) for all T1 Modes. If multiframe synchronization is lost (Synchronization and Alarm Status Word(Y10) Bit 12, MFSYNC = 1), the receive signaling bits are frozen. They will become unfrozen when multi - frame synchronization is acquired (this is the same as terminal frame synchronization for ESF links). When the CASRI interrupt is unmasked, IRQ will become active when a signaling state change is detected in any of the 24 receive channels and a selectable 1 msec, 4 msec or 8 msec timer(Y04 bit 0,1) has expired. This function helps to reduce the frequency of interrupts generated due to signaling changes. For instance if 7 channels had a signaling change only one interrupt will be generated in a 2, 8, or 16 msec duration. Upon an interrupt the user has to read the CAS registers(Y70 to Y87)to determine the channels with a signaling change.The CASRIM interrupt mask is located in register Y45 bit 2 (reset low to enable interrupt); and the CASRI interrupt status bit in register is Y35 bit 2. Any channels marked as clear channels will not generate an interrupt due to changes in ABCD bits. When bit 0 (CC) in the per timeslot control word (Y90 to YA7) is set no bit robbing for the purpose of signaling will occur in this channel and no signaling change interrupts will be generated by the channel. When bit 7 (MPST) is set, the transmit signaling for the addressed channel can only be programmed by writing to the transmit signaling page (Y50 to Y67) via the microport. If MPST is zero, the transmit signaling information is constantly updated with the information from the equivalent channel on CSTi.
SEMICMF.019
55
MT9072
Register Address 900 Y00 Register Global Control 0 Framing Mode Select Description
Data Sheet
CK1 determines an 8 Mhz stream or a 2 Mhz stream. STBUS selects a GCI or ST-BUS CSTi, CSTo streams. The number of signaling bits available is dependent on the mode. For D4 and T1DM 2 bits of signaling, for ESF 4 bits. In G.802 and IMA mode signaling is not supported. This register defines the selection between robbed bit or common channel, signaling debounce and substitute bits C,D bits for D4 mode on CSTo. Y04 bit 0 and 1 are used to control the frequency of the signaling change interrupt.
Y04
Signaling Control Word
Y0B Y10
Common Channel This register is used to determine the CSTi/o channel to PCM24 timeslot signaling Map Register mapping for common channel signaling. Synchronization and Alarm Status Word The receive signaling will not work if terminal frame synchronization and multiframe synchronization is not achieved. The clear channel bit can be used to block insertion of signaling in the transmit direction. The MPST bit can be used to determine the source of the transmit signaling, which is either the CSTi stream or the transmit signaling ram. The CASRI bit is set if unmasked and receive signaling changes on any channel. The channels marked as clear channel do not generate an interrupt. CASRIM is the mask bit for the Y35.
Y50-Y60 Per Channel Transmit signaling
Y35
Receive Line and Timer Interrupt Status Receive Line and Timer Interrupt Mask
Y45
Table 22 - Registers Related to Signaling (T1)
7.1.2
T1 Common Channel Signaling
One 64 Kbit/s channel can be mapped from/to an external multichannel HDLC using the CSTi/0 pins. This is accomplished by writing to register Y0B and Y04(CSIGEN bit). Note that only channels 0 to 23 can be used on the CSTi/o streams in Common Channel Signaling applications. For the CSTo stream only the channel that is selected is driven, the rest of the stream is tristate. In 8 Mbit/s mode up to 4 channels per 8Mbit/s CSTi/0 stream will be assigned to the external HDLC in accordance with Table 2.
7.2 7.2.1
E1 Signaling Channel Associated Signaling (CAS) Operation
The purpose of the CAS signaling Multiframing algorithm is to provide a scheme that will allow the association of a specific ABCD signaling nibble with the appropriate PCM30 channel. The signaling nibble when sinked or sourced from the ST-BUS will have the ABCD bits being bits 3 to 0 respectively. A CAS signaling multiframe consists of 16 basic frames (numbered 0 to 15), which results in a multiframe repetition rate of 2 msec. It should be noted that the boundaries of the signaling multiframe may be completely distinct from those of the CRC-4 multiframe. CAS multiframe alignment is based on a multiframe alignment signal (a 0000 bit sequence), which occurs in the most significant nibble of timeslot 16 of basic frame 0 of the CAS multiframe. Bits 5, 7 and 8 (usually designated X) are spare bits and are normally set to one if not used. Bit 6 of this timeslot is the multiframe alarm bit (usually designated Y). When CAS multiframing is acquired on the receive side, the transmit Ybit is zero; when CAS multiframing is not acquired, the transmit Y-bit is one. Refer to ITU-T G.704 and G.732 for
56
SEMICMF.019
Data Sheet
MT9072
more details on CAS multiframing requirements. Registers related to configuration and observation of the CAS signaling are shown in Table 23.
.
Register Address 900 Y00 Y02 Y03 Y04 Y05
Register Global Control 0 Alarm and Framing Control Register Interrupt and IO Control Register DL,CCS,CAS and other Control Register Signaling Interrupt Period Register CAS Control and Data Register HDLC and CCS ST-BUS Control Register Synchronization and CRC-4 Remote Status.
Description CK1 determines an 8.192 Mbits stream or a 2.048 Mbits stream. STBUS selects a GCI or ST-BUS CSTi, CSTo streams. Ensure that TAIS16 is off, the signaling information in CAS cannot be sent if TAIS16 is on. Also signaling is not supported in IMA mode. If CSTo is to contain the signaling nibbles set CSTOE to 1 and RXCO to 1. RXTRS which sets the receiver in a transparent mode has to be turned off. Bit 0 and 1 of this register determine the period of the interrupt CASRI. The period is selectable from 2 msec 8 msec and 16 msec. If RFL is set the receive signaling is frozen due to synchronization loss. If debounce is selected a 14 msec debounce is applied before the signaling is available in the csto or receive CAS register. TS31E, TS15E and TS16E have to be off since Common Channel signaling and CAS are mutually exclusive. MSYNC has to be low for the signaling in the Receive CAS Registers or CSTO has valid data.
Y06 Y10 Y26 Y36
CAS, National, CRC-4 Local The bit CASRL reflects the signaling changes on the receive CAS. and Timer Latch Status CAS, national, CRC-4 Local and Timer Interrupt Status National Interrupt Mask Register The CASRI will be set if a signaling Interrupt has occurred. The period of the interrupt is controlled by the signaling Interrupt Period Register(Y04). The bit CASRM can be used to mask interrupts from the receive signaling changes. The clear channel bit can be used to block insertion of signaling in the transmit direction. The CASS bit can be used to determine the source of the transmit signaling, which is either the CSTi or the transmit signaling ram. The CASS bit determines the source of the transmit signaling which is either the ST-BUS or the transmit signaling registers(Y51 to Y60).
Y46
Y51-Y6F Per Channel Transmit Signaling
Y90 to YAF
Per Channel Timeslot Control Register
Table 23 - Registers Related to CAS Signaling (E1)
Timeslot 16 of the remaining 15 basic frames of the CAS multiframe (i.e., basic frames 1 to 15) is reserved for the ABCD signaling bits for the 30 payload channels. The most significant nibbles are reserved for channels 1 to 15 and the least significant nibbles are reserved for channels 16 to 30. That is, timeslot 16 of basic frame 1 has ABCD for channel 1 and 16, timeslot 16 of basic frame 2 has ABCD for channel 2 and 17, through to timeslot 16 of basic frame 15 has ABCD for channel 15 and 30. See Table 24. Note that the ABCD bits for TS1 to TS15 should not be 0000 to prevent mimic of the multiframe alignment signal(0000).
SEMICMF.019
57
MT9072
CAS Frame 0 1 2 Channel Associated signaling (CAS) Multiframe (not related to CRC-4 multiframing) 3 4 5 6 7 8 9 10 11 12 13
MAS - Multiframe Alignment Signal NMAS - Non-multiframe Alignment Signal X - Spare Bit = 1 if not used Y - Remote Multiframe Alarm Signal
Data Sheet
PCM30 Timeslot 16 1 2 3 4 5 6 7 8
0000 (MAS) ABCD (ch 1 = ts1) ABCD (ch 2 = ts 2) ABCD (ch 3 = ts 3) ABCD (ch 4 = ts 4) ABCD (ch 5 = ts 5) ABCD (ch 6 = ts 6) ABCD (ch 7 = ts 7) ABCD (ch 8 = ts 8) ABCD (ch 9 = ts 9) ABCD (ch 10 = ts 10) ABCD (ch 11 = ts 11) ABCD (ch 12 = ts 12) ABCD (ch 13 = ts 13) ABCD (ch 14 = ts 14) ABCD (ch 15 = ts 15)
XYXX (NMAS) ABCD (ch 16 = ts 17) ABCD (ch 17 = ts 18) ABCD (ch 18 = ts 19) ABCD (ch 19 = ts 20) ABCD (ch 20 = ts 21) ABCD (ch 21 = ts 22) ABCD (ch 22 = ts 23) ABCD (ch 23 = ts 24) ABCD (ch 24 = ts 25) ABCD (ch 25 = ts 26) ABCD (ch 26 = ts 27) ABCD (ch 27 = ts 28) ABCD (ch 28 = ts 29) ABCD (ch 29 = ts 30) ABCD (ch 30 = ts 31)
14 15
Table 24 - Channel Associated Signaling (CAS) Multiframe Structure (E1)
7.2.2
E1 Channel Associated Signaling (CAS) Register and ST-BUS Access
The CSIG control bit (register address Y03) must be set to zero for Channel Associated signaling (CAS) operation. Access to the ABCD transmit and receive bits may be either through ST-BUS channels 1 to 15 and channels 17 to 31 at the CSTi and CSTo pins, or through the Transmit CAS Data registers (Y51-Y6F) and Receive CAS Data registers (Y71-Y8F) accessed by the parallel processor port, or through a mix of both methods. The timeslot control register bits (CASS(n) address Y90-YAF) determine the source of the CAS data on a per channel basis. A zero enables an ST-BUS source and a one enables a register source. Note that when changing the CASS(n) control bits from ST-BUS source to register source on the fly (during normal operation as opposed to during power up), the data in the Transmit CAS Data registers (Y51-Y6F) should be updated one frame after the timeslot control register bits (CASS(n)) are changed. This is because the timeslot control register bits do not take effect immediately. Both destinations of CAS data are always enabled (i.e. ST-BUS CSTo and receive data registers). ST-BUS CSTi and CSTo channels 0 and 16 are not used. When the CASRI interrupt is unmasked, IRQ will become active when a signaling state change is detected in any of the 30 receive channels and a selectable 2 msec, 8 msec or 16 msec timer(Y04 bit 0,1) has expired. This function helps to reduce the frequency of interrupts generated due to signaling changes. For instance if 7 channels had a signaling change only one interrupt will be generated in a 2,8 or 16 msec duration. Upon an interrupt the user has to read the CAS registers(Y70 to Y8F)to determine the channels with a signaling change.The CASRIM interrupt mask is located in register Y46 bit 4 (clear to enable interrupt); and the CASRI interrupt status bit in register is Y36
58
SEMICMF.019
Data Sheet
7.2.2.1
MT9072
bit 4. Any channels marked as clear channels will not generate an interrupt due to changes in ABCD bits.
E1 Channel Associated Signaling (CAS) Transmit from ST-BUS CSTi to PCM30
Table 25 shows the detailed bit mapping of CSTi timeslots to transmit PCM30 frames.
ST-BUS CSTi Frame Timeslot 0 0+n Data Bits (B7-B0) not used. Timeslot 16
PCM30 Transmit Data Bits (B1-B8) CAS Multiframe Alignment Signal
1m + n to #,#,#,#,A1, B1, C1, D1 to 15m + n #,#,#,#,A15, B15, C15, D15 16m + n not used.
17m + n to #,#,#,#,A16, B16, C16, D16, to 31m + n #,#,#,#,A30, B30, C30, D30 1 to 15 as above as above 16 A1, B1, C1, D1, A16, B16, C16, D16 to A15, B15, C15, D15, A30, B30, C30, D30
Note 1. For 2.048Mbit/s operation, m=1 and n=0. Note 2. For 8.192Mbit/s operation, m=4 and n =0,1,2,3 where n corresponds to the framer number (i.e. n=0=framer 0... n=3= framer 3) Note 3. The number following the ABCD signaling bit letter designates the channel number (i.e. A30 designates channel 30). Note 4. For these functions to be valid, CAS mode must be selected (CSIG=0 register address Y03), and the required ST-BUS channels must be enabled (CASS=0 of register address Y90-YAF). Note 5. # indicates data which is not transmitted.
Table 25 - Transmit PCM30 CAS Channels 1 to 30 from ST-BUS 2.048Mbit/s or 8.192Mbit/s CSTi (E1)
7.2.2.2
E1 Channel Associated Signaling (CAS) Receive from PCM30 to ST-BUS CSTo
Table 26 shows the detailed bit mapping of CSTo timeslots from receive PCM30 frames. ST-BUS CSTo Timeslot 0+n not used. Data Bits (B7-B0) Timeslot 16 PCM30 Receive Data Bits (B1-B8) CAS Multiframe Alignment Signal
CAS Frame 0
1m + n to 1,1,1,1,A1, B1, C1, D1, to 15m + n 1,1,1,1,A15, B15, C15, D15 16m + n not used. 17m + n to 1,1,1,1,A16, B16, C16, D16, to 31m + n 1,1,1,1,A30, B30, C30, D30 1 to 15
Note Note 3). Note Note Note
as above as above
16
A1, B1, C1, D1, A16, B16, C16, D16 to A15, B15, C15, D15, A30, B30, C30, D30
1. For 2.048Mbit/s operation, m=1 and n=0. 2. For 8.192Mbit/s operation, m=4 and n =0,1,2,3 where n corresponds to the framer number (i.e. n=0=framer 0... n=3= framer 3. The number following the ABCD signaling bit letter designates the channel number (i.e. A30 designates channel 30). 4. For these functions to be valid, CAS mode must be selected (CSIG=0 register address Y03). 5. "1" indicates bit positions in a logic high state.
Table 26 - Receive PCM30 CAS Channels 1 to 30 to ST-BUS 2.048Mbits or 8.192Mbits CSTo (E1)
SEMICMF.019
59
MT9072
7.2.3
Data Sheet
E1 Common Channel Signaling (CCS) Transmit from ST-BUS CSTi and DSTi to PCM30
The CSIG control bit (register address Y03) must be set to one for Common Channel signaling (CCS) operation. CCS on the transmit PCM30 link (bit positions one to eight of timeslots 15, 16 and/or 31 of every frame) may be sourced from the ST-BUS DSTi stream or from the ST-BUS CSTi stream. If the TS15E, TS16E & TS31E control bits (register address Y06) are zero, the transmit data will be sourced from the ST-BUS DSTi stream timeslots 15, 16 and 31, if these bits are one, then the signaling data will be sourced from the ST-BUS CSTi stream. Note that any combination of the TS15E, TS16E & TS31E control bits (register address Y06) may be enabled. The CSTi source timeslots for the PCM30 timeslot 15, 16 and 31, are determined respectively by the 15C4-15C0, 16C4-31C0 and 31C4-31C0 (register address Y07) programming bits. Table 27 shows the detailed bit mapping of CSTi timeslots to transmit PCM30 frames. Table 28 shows the detailed bit mapping of DSTi timeslots to transmit PCM30 frames.
ST-BUS CSTi CRC-4 Frame all all all Timeslot Data Bits (B7-B0)
PCM30 Transmit CRC-4 Timeslot Frame 15 16 31 all all all Data Bits (B1-B8) P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8
Any one of 32 P1, P2, P3, P4, P5, P6, P7, P8 n + m(0 to 31) Any one of 32 P1, P2, P3, P4, P5, P6, P7, P8 n + m(0 to 31) Any one of 32 P1, P2, P3, P4, P5, P6, P7, P8 n + m(0 to 31)
Note 1. For 2.048Mbit/s operation, m=1 and n=0. Note 2. For 8.192Mbit/s operation, m=4 and n =0,1,2,3 where n corresponds to the framer number (i.e. n=0=framer 0... n=3= framer 3) Note 3. For these functions to be valid, CCS mode must be selected (CSIG=1 register address Y03), and CSTi ST-BUS mode must be selected (TS15E=1, TS16E=1 & TS31E=1 register address Y06), and the preferred source CSTi timeslot should be selected (15C4-0, 16C4-0 & 31C4-0 register address Y07).
Table 27 - Transmit PCM30 CCS from ST-BUS 2.048Mbit/s or 8.192Mbit/s CSTi (E1) ST-BUS DSTi CRC-4 Frame all all all Timeslot n + m(15) n + m(16) n + m(31) Data Bits (B7-B0) P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8 Timeslot 15 16 31 PCM30 Transmit CRC-4 Frame all all all Data Bits (B1-B8) P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8
Note 1. For 2.048Mbit/s operation, m=1 and n=0. Note 2. For 8.192Mbit/s operation, m=4 and n =0,1,2,3 where n corresponds to the framer number (i.e. n=0=framer 0... n=3= framer 3). Note 3. For these functions to be valid, CCS mode must be selected (CSIG=1 register address Y03), and DSTi ST-BUS mode must be selected (TS15E=0, TS16E=0 & TS31E=0 register address Y06).
Table 28 - Transmit PCM30 CCS from ST-BUS 2.048Mbit/s or 8.192Mbit/s DSTi (E1)
7.2.4
E1 Common Channel Signaling (CCS) Receive from PCM30 to CSTo and DSTo
The CSIG control bit (register address Y03) must be set to one for Common Channel signaling (CCS) operation. CCS on the receive PCM30 link (bit positions one to eight of timeslots 15, 16 and/or 31 of every frame) is sourced to the ST-BUS DSTo stream and may also be sourced to the ST-BUS CSTo stream. If the TS15E, TS16E & TS31E control bits (register address Y06) are zero, the receive data will be sourced to the ST-BUS DSTo stream only, timeslots 15, 16 and 31. If these bits are one, then the signaling data will be sourced to both the DSTo stream and
60
SEMICMF.019
Data Sheet
MT9072
the ST-BUS CSTo stream. Note that any combination of the TS15E, TS16E & TS31E control bits (register address Y06) may be enabled. The CSTo destination timeslots for the receive PCM30 timeslots 15, 16 and 31, are determined respectively by the 15C4-15C0, 16C4-31C0 and 31C4-31C0 (register address Y07) programming bits. Table 29 shows the detailed bit mapping of CSTo timeslots from receive PCM30 frames. Table 30 shows the detailed bit mapping of DSTo timeslots from receive PCM30 frames.
ST-BUS CSTo CRC-4 Frame all all all Timeslot Data Bits (B7-B0) Timeslot 15 16 31
PCM30 Receive CRC-4 Frame all all all Data Bits (B1-B8) P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8
Any one of 32 P1, P2, P3, P4, P5, P6, P7, P8 n + m(0 to 31) Any one of 32 P1, P2, P3, P4, P5, P6, P7, P8 n + m(0 to 31) Any one of 32 P1, P2, P3, P4, P5, P6, P7, P8 n + m(0 to 31)
Note 1. For 2.048Mbit/s operation, m=1 and n=0. Note 2. For 8.192Mbit/s operation, m=4 and n =0,1,2,3 where n corresponds to the framer number (i.e. n=0=framer 0... n=3= framer 3) Note 3. For these functions to be valid, CCS mode must be selected (CSIG=1 register address Y03), and CSTo ST-BUS mode must be selected (TS15E=1, TS16E=1 & TS31E=1 register address Y06), and the preferred destination CSTo timeslot should be selected (15C4-0, 16C4-0 & 31C4-0 register address Y07).
Table 29 - Receive PCM30 CCS to ST-BUS 2.048Mbit/s or 8.192Mbit/s CSTo (E1)
ST-BUS DSTo CRC-4 Frame all all all Timeslot Data Bits (B7-B0) Timeslot 15 16 31
PCM30 Receive CRC-4 Frame all all all Data Bits (B1-B8) P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8 P1, P2, P3, P4, P5, P6, P7, P8
n + m(15) P1, P2, P3, P4, P5, P6, P7, P8 n + m(16) P1, P2, P3, P4, P5, P6, P7, P8 n + m(31) P1, P2, P3, P4, P5, P6, P7, P8
Note 1. For 2.048Mbit/s operation, m=1 and n=0. Note 2. For 8.192Mbit/s operation, m=4 and n =0,1,2,3 where n corresponds to the framer number (i.e. n=0=framer 0... n=3= framer 3) Note 3. For these functions to be valid, CCS mode must be selected (CSIG=1 register address Y03).
Table 30 - Receive PCM30 CCS to ST-BUS 2.048Mbit/s or 8.192Mbit/s DSTo (E1)
7.2.5
CCS (Timeslot 16) Programming Options Summary Table
SEMICMF.019
61
MT9072
Control Bit CSIG=1 TS15E=1 15C4-0=n CSIG=1 TS15E=1 16C4-0=n CSIG=1 TS15E=1 31C4-0=n CSIG=1 TS15E=0 CSIG=1 TS16E=0 CSIG=1 TS31E=0 CSIG=1 TS15E=1 15C4-0=n CSIG=1 TS16E=1 16C4-0=n CSIG=1 TS31E=1 31C4-0=n CSIG=1 Register Y03 Y06 Y07 Y03 Y06 Y07 Y03 Y06 Y07 Y03 Y06 Y03 Y06 Y03 Y06 Y03 Y06 Y07 Y03 Y06 Y07 Y03 Y06 Y07 Y03 all n where n=0-31 ST-BUS DSTo 31 16 PCM30 RPOS-RNEG 15 ST-BUS CSTo 31 ST-BUS DSTi 15 any n where n=0-31 any n where n=0-31 Method ST-BUS CSTi Data Source *Bits P1-P8 Timeslot or Register any n where n=0-31 Method PCM30 TPOS-TNEG
Data Sheet
Data Destination *Bits P1P8 Timeslot or Register 15
16
31
15
16
16
31
any nwhere n=0-31
any n where n=0-31
any n where n=0-31
all n where n=0-31
* Notes 1. ST-BUS "Bits" are from MSB (B7) to LSB (B0) with P1 the MSB 2. PCM30 "Bits" are from MSB (B1) to LSB (B8) with P1 the MSB
Table 31 - CCS (Timeslot 15, 16 & 31) Source and Destination Summary Table (E1)
62
SEMICMF.019
Data Sheet
8.0 HDLC
MT9072
The MT9072 has 1 embedded HDLC controller for each of the framers. Each controller may be attached to any timeslot. The HDLC can also be connected to the FDL bits (T1 ESF Mode) for provision of a 4 Kbit/s Data Link or Sa bits in E1 mode for data link up to 20Kb/s. The features of the HDLC are: * Independent transmit and receive FIFO; * Receive FIFO maskable interrupts for nearly full and overflow conditions; * Transmit FIFO maskable interrupts for nearly empty and underflow conditions; * Maskable interrupts for transmit end-of-packet and receive end-of-packet; * Maskable interrupts for receive bad-frame (includes frame abort); * Transmit end-of-packet and frame-abort functions. The relevant registers associated with HDLC are listed in Table 32.
Register Address Y06 YF2 YF3 YF4 YF5
Register HDLC and DataLink Control HDLC Control HDLC Test Control Address Recognition Transmit FIFO
Description The bits of this register determine whether the HDLC is connected to the Data Link or payload. General configuration for the HDLC. Control bits for testing the HDLC such as loopbacks. Address recognition register for storing data in the Receive FIFO of a packet that matches the received address. This register is used for writing data to the HDLC Transmit FIFO. The data from the FIFO can be subsequently sent to Data Link or a selected channel. This counter determines the size of the HDLC packet to be sent when the cycle bit is set(YF2). This register provides status on the FIFO's. This register provides the received FCS of a packet. This register has to be read to obtain the receive FIFO data. These register bits are the latched version of the HDLC status. This register provides the interrupt status of events such as underflow, go ahead packet etc. These register bits can be used to mask HDLC events to cause interrupts. Table 32 - HDLC Related Registers
YF6 Y1D Y1E Y1F Y23 Y33 Y43
Transmit Byte Counter HDLC Status Receive CRC Receive FIFO HDLC Latch Status HDLC Interrupt Status HDLC Interrupt Mask
8.1
HDLC Description
The HDLC handles the bit oriented protocol structure as per layer 2 of the switching protocol X.25 defined by CCITT. It transmits and receives the packetized data serially while providing data transparency by zero insertion and deletion. It generates and detects the flags, various link channel states and abort sequences. Further, it
SEMICMF.019
63
MT9072
Data Sheet
provides a cyclic redundancy check on the data packets using the CCITT defined polynomial. In addition, it can recognize a single byte, dual byte and all call address in the received frame. Access to Rx CRC and inhibiting of Tx CRC for terminal adaptation is also provided. The HDLC controller has two 32 byte deep FIFO's associated with it; one for Transmit and one for Receive.
8.1.1
HDLC Frame Structure
A valid HDLC frame begins with an opening flag, contains at least 16 bits of address and control or information, and ends with a 16 bit FCS followed by a closing flag. Data formatted in this manner is also referred to as a "packet". Refer to Table 33.
Flag (7E) One Byte 01111110 n Bytes n2
Data Field
FCS Two Bytes
Flag (7E) One Byte 01111110
Table 33 - HDLC Frame Format
All HDLC frames start and end with a unique flag sequence "01111110". The transmitter generates these flags and appends them to the packet to be transmitted. The receiver searches the incoming data stream for the flags on a bit- by-bit basis to establish frame synchronization. The data field consists of an address field, control field and information field. The address field consists of one or two bytes directly following the opening flag. The control field consists of one byte directly following the address field. The information field immediately follows the control field and consists of N bytes of data. The HDLC does not distinguish between the control and information fields and a packet does not need to contain an information field to be valid. The FCS field, which precedes the closing flag, consists of two bytes. A cyclic redundancy check utilizing the CRCCCITT standard generator polynomial "X16+X12+X5+1" produces the 16-bit FCS. In the transmitter the FCS is calculated on all bits of the address and data field. The complement of the FCS is transmitted, most significant bit first, in the FCS field. The receiver calculates the FCS on the incoming packet address, data and FCS field and compares the result to "F0B8". If no transmission errors are detected and the packet between the flags is at least 32 bits in length then the address and data are entered into the receive FIFO minus the FCS which is discarded.
8.1.2
Data Transparency (Zero Insertion/Deletion)
Transparency ensures that the contents of a data packet do not imitate a flag, go-ahead, frame abort or idle channel. The contents of a transmitted frame, between the flags, is examined on a bit-by-bit basis and a 0 bit is inserted after all sequences of 5 contiguous 1 bits (including the last five bits of the FCS). Upon receiving five contiguous 1s within a frame the receiver deletes the following 0 bit.
8.1.3
Invalid Frames
A frame is invalid if one of the following four conditions exists (Inserted zeros are not part of a valid count): * * * * If the FCS pattern generated from the received data does not match the "F0B8" pattern then the last data byte of the packet is written to the received FIFO with a `bad packet' indication. A short frame exists if there are less than 25 bits between the flags. Short frames are ignored by the receiver and nothing is written to the receive FIFO. Packets which are at least 26 bits in length but less than 32 bits between the flags are also invalid. In this case the data is written to the FIFO but the last byte is tagged with a "bad packet" indication. If a frame abort sequence is detected the packet is invalid. Some or all of the current packet will reside in the receive FIFO, assuming the packet length before the abort sequence was at least 25 bits long.
64
SEMICMF.019
Data Sheet
8.1.4 Frame Abort
MT9072
The transmitter will abort a current packet by substituting a zero followed by seven contiguous 1s in place of the normal packet. The receiver will abort upon reception of seven contiguous 1s occurring between the flags of a packet which contains at least 25 bits. Note that should the last received byte before the frame abort end with contiguous 1s, these are included in the seven 1s required for a receiver abort. This means that the location of the abort sequence in the receiver may occur before the location of the abort sequence in the originally transmitted packet. If this happens then the last data written to the receive FIFO will not correspond exactly with the last byte sent before the frame abort.
8.1.5
Interframe Time Fill and Link Channel States
When the HDLC transmitter is not sending packets it will wait in one of two states Interframe Time Fill state: This is a continuous series of flags occurring between frames indicating that the channel is active but that no data is being sent. * Idle state: An idle Channel occurs when at least 15 contiguous 1s are transmitted or received. In both states the transmitter will exit the wait state when data is loaded into the transmitter FIFO. *
8.1.6
Go-Ahead
A go ahead is defined as the pattern "011111110" (contiguous 7Fs) and is the occurrence of a frame abort sequence followed by a zero, outside of the boundaries of a normal packet. Being able to distinguish a proper (in packet) frame abort sequence from one occurring outside of a packet allows a higher level of signaling protocol which is not part of the HDLC specifications.
8.1.7
Functional Description
The HDLC transceiver can be reset by either the power reset input signal or by the HRST Control bit in the HDLC Test control register (YF3). When reset, the HDLC Control Registers are cleared, resulting in the transmitter and receiver being disabled. The Receiver and Transmitter can be enabled independent of one another through HDLC control(YF2 bits RXEN and TXEN). The transceiver input and output are enabled when the enable control bits in HDLC control are set. Transmit to receive loopback as well as a receive to transmit loopback are also supported. Transmit and receive bit rates and enables can operate independently. Received packets from the serial interface, are sectioned into bytes by an HDLC receiver that detects flags, checks for go-ahead signals, removes inserted zeros, performs a cyclical redundancy check (CRC) on incoming data, and monitors the address if required. Packet reception begins upon detection of an opening flag. The resulting bytes are concatenated with two status bits (RQ9, RQ8 in HDLC status register Y1D) and placed in a receiver first-in-firstout (Rx FIFO); a buffer register that generates status and interrupts for microprocessor read control. In conjunction with the control circuitry, the microprocessor writes data bytes into a Tx buffer register (Tx FIFO) that generates status and interrupts. Packet transmission begins when the microprocessor writes a byte to the Tx FIFO. Two status bits are added to the Tx FIFO for transmitter control of frame aborts (FA) and end of packet (EOP) flags. Packets have flags appended, zeros inserted, and a CRC, also referred to as frame checking sequence (FCS), added automatically during serial transmission. When the Tx FIFO is empty and finished sending a packet, Interframe Time Fill bytes (continuous flags (7E hex)), or Mark Idle (continuous ones) are transmitted to indicate that the channel is idle.
8.1.8
HDLC Transmitter
Following initialization and enabling, the transmitter is in the Idle Channel state (Mark Idle), continuously sending ones. Interframe Time Fill state (Flag Idle) is selected by setting the MI bit in register YF2 high1. The Transmitter remains in either of these two states until data is written to the Tx FIFO. YF2 bits EOP (end of packet) and FA (Frame Abort) are set as status bits before the microprocessor loads 8 bits of data into the 10 bit wide FIFO (8 bits data and 2 bits status). To change the tag bits being loaded in the FIFO, HDLC Master Control must be written to before writing to the FIFO. However, EOP and FA are reset after writing to the TX FIFO. The Transmit Byte Count
SEMICMF.019
65
MT9072
Data Sheet
Register(YF6) may also be used to tag an end of packet. The register is loaded with the number of bytes in the packet and decrements after every write to the Tx FIFO. When a count of one is reached, the next byte written to the FIFO is tagged as an end of packet. The register may be made to cycle through the same count if the packets are of the same length by setting HDLC Master Control bit Cycle. If the transmitter is in the Idle Channel state when data is written to the Tx FIFO, then an opening flag is sent and data from Tx FIFO follows. Otherwise, data bytes are transmitted as soon as the current flag byte has been sent. Tx FIFO data bytes are continuously transmitted until either the FIFO is empty or an EOP or FA status bit is read by the transmitter. After the last bit of the EOP byte has been transmitted, a 16-bit FCS is sent followed by a closing flag. When multiple packets of data are loaded into Tx FIFO, only one flag is sent between packets. When the HDLC is connected to FDL or a transmit channel The least significant bit of the Transmit FIFO data is sent first on the serial stream. Frame aborts (the transmission of 7F hex), are transmitted by tagging a byte previously written to the Tx FIFO. When a byte has an FA tag, then an FA is sent instead of that tagged byte. That is, all bytes previous to but not including that byte are sent. After a Frame Abort, the transmitter returns to the Mark Idle or Interframe Time Fill state, depending on the state of the Mark idle control bit. Tx FIFO underrun will occur if the FIFO empties and the last byte did not have either an EOP or FA tag. A frame abort sequence will be sent when an underrun occurs. Below is an example of the transmission of a three byte packet ('AA' '03' '77' hex) (Interframe time fill). TXcen can be enabled before or after this sequence. (a) Write'0020'hex to Control Register 1 -Mark idle bit set (b) Write'AA' hex to TX FIFO -Data byte (c) Write'03'hex to TX FIFO -Data byte (d) Write'01A0' hex to Control Register 1 -TXEN; EOP; Mark idle bits set (e) Write'77'hex to TX FIFO -Final data byte The transmitter may be enabled independently of the receiver. This is done by setting the TXEN bit of the Control Register YF2. Enabling happens immediately upon writing to the register. Disabling using TXen will occur after the completion of the transmission of the present packet; the contents of the FIFO are not cleared. Disabling will consist of stopping the transmitter clock. The Status and Interrupt Registers may still be read and the FIFO and Control Registers may be written to while the transmitter is disabled. The transmitted FCS may be inhibited using the Tcrci bit of HDLC Master Control Register. In this mode the opening flag followed by the data and closing flag is sent and zero insertion still included, but no CRC. That is, the FCS is injected by the microprocessor as part of the data field. This is used in V.120 terminal adaptation for synchronous protocol sensitive UI frames.
8.1.9
HDLC Receiver
After initialization and enabling, the receiver clocks in serial data, continuously checking for Go-aheads (0 1111 1110), flags (0111 1110), and Idle Channel states (at least fifteen ones). When a flag is detected, the receiver synchronizes itself to the serial stream of data bits, automatically calculating the FCS. If the data length between flags after zero removal is less than 25 bits, then the packet is ignored so no bytes are loaded into Rx FIFO. When
1. If the MT9072A HDLC transmitter is set up in the Mark-Idle state (YF2 MI is 1) then it will occasionally (less than 1% of the time) fail to transmit the opening flag when it is changed from the disabled state to the enabled state (YF2 TXEN changed from 0 to1). A missing opening flag will cause the packet to be lost at the receiving end. This problem only affects the first packet transmitted after the HDLC transmitter is enabled. Subsequent packets are unaffected.
66
SEMICMF.019
Data Sheet
MT9072
the data length after zero removal is between 25 and 31 bits, a first byte and bad FCS code are loaded into the Rx FIFO (see definition of RQ8 and RQ9 below). If address recognition is required, the Receiver Address Recognition Registers are loaded with the desired address and the Adrec bit in the HDLC Control Register is set high(YF2). Bit 0 and 8 of the Address Register are used as enable bits for their respective byte, thus allowing either or both of the first two bytes to be compared to the expected values. Bit 0 of the first byte of the address received (address extension bit) will be monitored to determine if a single or dual byte address is being received. If this bit is 0 then a two byte address is being received and then only the first six bits of the first address byte are compared. An all call condition is also monitored for the second address byte; and if received the first address byte is ignored (not compared with mask byte). If the address extension bit is a 1 then a single byte address is being received. In this case, an all call condition is monitored for in the first byte as well as the mask byte written to the comparison register and the second byte is ignored. Seven bits of address comparison can be realized on the first byte if this is a single byte address by setting the Seven bit of HDLC control register(YF2).
The following two Status Register bits (RQ8 and RQ9) are appended to each data byte as it is written to the Rx FIFO. They indicate that a good packet has been received (good FCS and no frame abort), or a bad packet with either incorrect FCS or frame abort. The Status and Interrupt Registers should be read before reading the Rx FIFO since Status and Interrupt information correspond to the byte at the output of the FIFO (i.e. the byte about to be read). The Status Register bits are encoded as follows:
RQ9 RQ8 Byte status 1 1 last byte (bad packet) 0 1 first byte 1 0 last byte (good packet) 0 0 packet byte The end-of-packet-detect (EOPD) interrupt indicates that the last byte written to the Rx FIFO was an EOP byte (last byte in a packet). The end-of-packet-read (EOPR) interrupt indicates that the byte about to be read from the Rx FIFO is an EOP byte (last byte in a packet). The Status Register should be read to see if the packet is good or bad before the byte is read. A minimum size packet has an 8-bit address, an 8-bit control byte, and a 16-bit FCS pattern between the opening and closing flags. Thus, the absence of a data transmission error and a frame length of at least 32 bits results in the receiver writing a valid packet code with the EOP byte into Rx FIFO. The last 16 bits before the closing flag are regarded as the FCS pattern and will not be transferred to the receiver FIFO. Only data bytes (Address, Control, Information) are loaded into the Rx FIFO. In the case of an Rx FIFO overflow, no clocking occurs until a new opening flag is received. In other words, the remainder of the packet is not clocked into the FIFO. Also, the top byte of the FIFO will not be written over. If the FIFO is read before the reception of the next packet then reception of that packet will occur. If two beginning of packet conditions (RQ9=0;RQ8=1) are seen in the FIFO, without an intermediate EOP status, then overflow occurred for the first packet. The receiver may be enabled independently of the transmitter. This is done by setting the RXEN bit of HDLC Control Register. Enabling happens immediately upon writing to the register. Disabling using RXEN will occur after the present packet has been completely loaded into the FIFO. Disabling can occur during a packet if no bytes have been written to the FIFO yet. Disabling will consist of disabling the internal receive clock. The FIFO, Status, and Interrupt Registers may still be read while the receiver is disabled. Note that the receiver requires a flag before processing a frame, thus if the receiver is enabled in the middle of an incoming packet it will ignore that packet and wait for the next complete one. The receive CRC can be monitored in the Rx CRC Register(Y1E). This register contains the actual CRC sent by the other transmitter in its original form; that is, MSB first and bits inverted. These registers are updated at each end of packet (closing flag) received and therefore should be read when an end of packet is received so that the next packet does not overwrite the registers.
SEMICMF.019
67
MT9072
9.0
9.1
Data Sheet
MT9072 Access and Control
Processor Interface (A11-A0, D15-D0, I/M, DS, R/W, CS, IRQ, Pins)
The control and status of the MT9072 is achieved through a non-multiplexed parallel microprocessor port capable of accommodating 12 address bits and 16 data bits. The parallel port may be configured for Motorola style control signals (by setting pin I/M low) or Intel style control signals (by setting pin I/M high).
9.1.1
Framer and Register Access
The controlling microprocessor gains access to specific registers and framers in the MT9072 through a single step process. Each of the eight internal framers is identified by the upper four address bits (A11-A8). Addresses 0XX, 1XX, 2XX... 7XX (where X indicates any hex number between 0 and F) access framers 0,1,2... 7 respectively. Address 8XX accesses all 8 framers simultaneously for processor writes. In addition, there are seven registers which are global to all eight framers; the Interrupt Vector and the Interrupt Vector Mask Registers, ST-BUS Select Register and ST-BUS analyzer control registers. These are accessed with addresses 900 to 911. Throughout this document, the upper four address bits (A11-A8) are referred to as Y, (where Y indicates any hex number between 0 and 7). Each register in the eight internal framers is identified by the lower eight address bits (A7-A0). All registers provided in each of the eight framers are identical, with identical lower eight bit addresses. The lower eight address bits are partitioned such that the upper four bits (A7-A4) identify the register group (i.e. Control, Status, Interrupt Mask etc.) and the lower four bits (A3-A0 identify the particular register in the register group (i.e. Tx Alarm Control Word,signaling Control Word etc.), see Table 34.
Address A11,A10,A9,A8 Selects the framer(s) (i.e. 0, 1, 2, 3,4,5,6,7,all, global) A7,A6,A5A4 A3,A2,A1,A0
Selects the register group (i.e. Selects the particular register in the Control, Status, Interrupt Mask etc.) register group (i.e. PRBS Error Counter etc.) Table 34 - Framer and Register Access
See Figures 22 and 23 for processor timing requirements. See the Registers section for detailed register descriptions. The MT9072 includes a status register which contains a15 bit identification code(address 912) for the MT9072. This code identifies the marketing revision. This byte allows user software to track device revisions, and device variances and provide system variations if necessary. Refer to the registers section for details.
9.1.1.1
CS and IRQ
The MT9072 includes a CS pin for applications where a single processor is controlling numerous peripherals. Processor access can be disabled without affecting framer operation. Refer to the CS pin description for details. An IRQ pin is provided with an extensive suite of maskable interrupts. Refer to the IRQ pin description and the interrupt section for interrupt processing details.
9.1.2
ST-BUS Interface (DSTi, DSTo, CSTi, CSTo Pins)
The ST-BUS is used for data and signaling access only and does not carry any MT9072 control information. Payload data is accessed through the DSTi and DSTo streams. Channel Associate Signalling bits and Common Channel Signaling bits can be accessed through CSTi and CSTo streams. See Tables 2 to 6 for ST-BUS Channel to transmit/receive timeslot mapping.
68
SEMICMF.019
Data Sheet
MT9072
Dedicated data link pins are included which provide the user the option of bypassing the receive elastic buffer and accessing data link (DL) data with an external controller. The MT9072 provides numerous additional methods for accessing the DL, refer to the data link sections for details.
9.1.3
IMA Interface (DSTi, DSTo, Pins)
In the IMA (Inverse Mux for ATM) mode the transmit and receive timing on the backplane are independent unlike the ST-BUS where all of the streams (DSTi/DSTo) are synchronous with a single clock (CKI) and a single frame pulse (FPI). The IMA mode is specifically intended to interface to the Zarlink IMA devices such as MT90220. In IMA mode the RXBF and RXDLC pins provide the receive frame pulse and receive clock for the data appearing at the DSTo pin. The FPi and CKi pins are inputs for the transmit frame pulse and transmit clock for data appearing at the DSTi pin. Note that in the IMA Mode, the slip buffers will be bypassed. On the transmit side data is accepted in the DSTi streams with respect to the CKi clock. The transmit clock TXCL (an input clock in T1 Mode) has to be synchronous to the CKi clock. On the receive side the EXCLi clock is the master and the DSTo data is synchronous to the EXCLi clock. In T1 IMA mode the backplane operates at 1.544 Mbit/s with the frame pulse centered on the S-Bit, the timing diagrams are shown in Figures 32 and 33. In order to provide the extracted 1.544 Mbit/s clock the E1.5CK bit in the Data Link Control Register (Y06) must be set. The receive and transmit slip buffers are bypassed in this mode. In E1 IMA mode the backplane operates at 2.048Mbit/s in a manner similar to the ST-BUS, the timing diagrams are shown in Figures 51 and 52. The receive slip buffer is bypassed in this mode. Note that in IMA mode the ST-BUS selection in register 900 is ignored. If IMA mode is selected the following functions are not supported: * * * * * * 8.192 Mbits backplane mode Robbed bit signaling and CAS Digital milliwat patterns One, two second timers and latching of counters at 1 sec timer GCI mode Data link insertion extraction of FDL (the HDLC can be assigned to the FDL IMA mode) Register Address Y00 Y06 Register Framing Mode Select HDLC & Datalink Control Description Setting the IMA bit will cause the framer to enter IMA mode. E1.5CK bit must be set to provide a 1.544 MHz clock on RXDLC.
Table 35 - Registers Related to IMA Mode
9.1.4
Signaling Multiframe Boundary (RxMF, TxMF Pins)
Dedicated multiframe boundary pins are included which provide the user the option of setting the multiframe boundaries and identifying the multiframe boundaries with an external device. Refer to the RxMF and TxMF pin descriptions.
9.1.5 9.1.5.1
Control Pins Reset Operation (RESET Pin, RST Bit and RSTC Bit)
SEMICMF.019
69
MT9072
Data Sheet
The MT9072 can be reset using the hardware RESET pin or the software reset bits: RST (register address YF1) and RSTC (address 900). The RST bit resets a particular framer and the RSTC bit is a global software reset bit. On initial power up, a hard reset must be done using the RESET pin. A valid reset condition requires both of these inputs to be held low for a minimum of 100ns. These inputs should be set to zero during initial power up, then set to one. After initial power up, the MT9072 can be reset using the hardware RESET pin or the software reset bit RSTC (register address 900). When the device emerges from its reset state, it will begin to function in T1 mode and the control registers will be initialized as described in Table 36. Clearing the T1E0 bit in register 900 to place the MT9072 in E1 mode will cause another internal reset and the control registers will be initialized to their E1 defaults as described in Table 37. In addition, individual framers may be reset with the software reset bit RST. Using the RST will reset the individual framer to its default E1 or T1 setting. RST will not affect the common control register (9xx). All reset operations take 1 full frame (125 us) to complete. Refer to the RESET pin description, RSTC and RST bit descriptions for additional details.
Function Framing Mode
Status Mode D4,Reframe criteria is set for 2 bits errors in 4 bits,Fs bit is not included in the synchronization criteria,S-bit not included in CRC calculation. The elastic stores are not bypassed.
Control Bits Reset Value RELBY,TELBY,TRANSP,T1DM,ESF,SL C96,CXC,RS10,FSI,ReFR,MFReFR,JTS ,TXSYNC =0
Register Address Y00
Line Coding and The T1 interfaces are set to NRZ, RZCS1:0,TZCS2:0TPDV,TXB8ZS,RXB8 Interface Bipolar,and Rising edge of clocks for ZS,ADSEQ,RZNRZ,UNIBI,CLKE = 0 output and falling for input line clocks.TxB8ZS and RxB8ZS and Transmit PDV enforcer is turned off. Transmit Alarms All sending alarms are deactivated. Transmit Error Insertion Signaling All error insertion controls are disabled. TESFYEL,TXSECY,TD4YEL,TAIS, #,T1DMY,D4SECY,SO = 14 L32Z,BPVE,CRCE,FTE,FSE,LOSE,PER R=0
Y01
Y02 Y03 Y04
All signaling freeze and debounce CSIGEN,RBEN,TSDB,RSDB,RFL,SM1functions are disabled and the 0,SIP1-0= hex 200 transmit signaling type is set such that A in frame 6 and B in frame 12. Robbed bit signaling is turned on for transmitter and receiver. All loopbacks deactivated; ready to DLBK,RLBK,STLBK,PLBK,TLU, send receive framed in band loopback TLD = 0 codes. Data Link is deactivated, hence bit oriented message, and HDLC are also disabled. The Transmit Bit oriented message register and Receive Bit oriented Match register are cleared. #,#,#,#,HCH4:0,HPAYSEL,E1.5CK, DLCK,EDLEN,BOMEN,HDLCEN,H1R6 4=0 TxBOM7:0, RXBOMM7:0 = 0
Loopbacks
Y05
Data Link
Y06
Bit Oriented Message Registers
Y07-Y08
Table 36 - Reset Status (T1)
70
SEMICMF.019
Data Sheet
Function Status Control Bits Reset Value TXLACL1-0,TXLAC7-0 = binary00 00000001 TXLDCL1-0,TXLDC7-0 = binary 01 00001001 RXLACL1-0,RXLACM7-0 = binary00 00000001 RXLDCL1-0,RXLDCM7-0 = binary 01 00001001
MT9072
Register Address Y0D-Y0F YF0
In band loopback The transmit and expected receive activation codes inband loopback codes are set to T1.403 defaults.
Interrupts and IO Control Latched Status Per Channel Control
All interrupts are suspended and CSTO and DSTo enables are off All latched status bits are cleared Per Channel inversion, Remote timeslot loopback, local timeslot loopback,transmit test, receive test, Clear channel, Receive freeze, transmit freeze are all turned off
Tx8KEN,RXDO,TXMFSEL, SPND,INTA,DSToEN,CSToEN,RxCO,C NTCLR,SAMPLE,RST = 0
YF1
Y10-Y2F RPCI,MPDR,MPST,TCPI,RTSL,LTSL,TT ST,RRST,MPDT,CC=0 Y90-YAF
Interrupts Masks All interrupts are unmasked. and status Registers
Receive Sync and Alarm status & Mask, Counter statusMask, Receive Line Status Mask, Elastic store status mask and HDLC Status Mask = 0
Y43 TO Y46
Table 36 - Reset Status (T1)
Function Mode Loopbacks Transmit FAS Transmit non-FAS
Status Termination Deactivated Cn0011011 1/Sn1111111
Control Bits RxTRS=0, TxTRS=0 DLBK,RLBK,SLBK,PLBK=0 RTSL(n), LTSL(n)=0 CSYN=0
Register Address Y03 Y01 Y90-YAF Y00 Y03 Y03 Y03
Transmit MFAS (CAS) Data Link Pin CRC Interworking Signaling ABCD Bit Debounce Interrupts RxMF Output
00001111 Deactivated Activated CAS ST-BUS Source Deactivated All Unmasked Suspended signaling Multiframe
TMA1,2,3,4=0 X1,Y,X2,X3=1 Sa4SS1-0,Sa5SS1-0,Sa6SS10,Sa7SS1-0,Sa8SS1-0=0 AUTC=0 CSIG=0 CASS(n)=0 DBNCE=0 ALL MASK BITS =0 SPND=0, INTA=0 MFSEL=0
Y05 Y05 Y08 Y00 Y03 Y50-Y6F Y05 Y40-Y43 Y02 Y02
Table 37 - Reset Status (E1)
SEMICMF.019
71
MT9072
Function Error Insertion Counters Counter Latches Per Timeslot Control Buffer All Other Control Registers Status Deactivated Cleared Cleared All locations cleared All locations cleared Control Bits E1, E2, BPVE,CRCE,FASE, NFSE,LOSE,PERR=0 ALL BITS =0 ALL BITS =0 ALL BITS =0 ALL BITS =0
Data Sheet
Register Address Y01 Y15-Y1A Y28-Y2B Y90-YAF All Other Control
Table 37 - Reset Status (E1)
9.1.5.2
Transmit AIS Operation (TAIS Pin)
The TAIS pin allows all eight framers of the MT9072 to transmit an all ones signal (AIS) at the TPOS and TNEG output pins from the point of power-up, without the need to write any control registers. During this time the IRQ pin is in a high impedance state. After the interface has been initialized normal operation can take place by making TAIS high.
9.1.5.3
IEEE 1149.1-1990 Test Access Port (TAP)
Five signals (TDI, TDO, TMS, TCK & TRST) make up the Test Access Port (TAP) of the IEEE 1149.1-1990 Standard Test Port and Boundary-Scan Architecture. The TAP provides access to test support functions built into the MT9072. The TAP is also referred to as a JTAG (Joint Test Action Group) port. See the JTAG section for additional details.
9.1.6
Data Link (DL) Interface (RxDL, RxDLC, TxDL, TxDLC Pins)
Dedicated data link pins are included which provide the user the option of bypassing the receive elastic buffer and accessing timeslot 0 data link (DL) data with an external controller. The MT9072 provides numerous additional methods for accessing the DL, refer to the DL sections for details.
9.1.7
Multiframe Boundary (RxMF, TxMF Pins)
Dedicated multiframe boundary pins are included which provide the user the option of setting the multiframe boundaries and identifying the multiframe boundaries with an external device. Refer to the RxMF and TxMF pin descriptions for more details.
10.0
ST-BUS Analyzer
The ST-BUS Analyzer is a powerful system diagnostic and debugging tool. The ST-BUS Analyzer allows for the capture of any ST-BUS data stream or channel to a 32 byte memory. The ST-BUS Analyzer can capture a single frame of data or 32 samples of a specified channel from DSTi, DSTo, CSTi or CSTo from any one of the 8 framers. The analysis can be performed continuously or on a single shot basis where 32 bytes are captured and then the analysis is suspended. An optional interrupt can be generated when a single shot analysis is complete. The operation of the ST-BUS analyzer is controlled by Global Control Register 1 (901).
11.0
11.1
Loopbacks
T1 Loopbacks
In order to meet PRI Layer 1 requirements and to assist in circuit fault sectionalization, the MT9072 has 7 loopback functions. The control bits for digital, remote, ST-BUS and payload loopbacks are located at address Y05. The remote and local timeslot loopbacks are controlled through control bits of the Timeslot Control register located at addresses Y90-
72
SEMICMF.019
Data Sheet
YA7.
MT9072
a) Digital loopback (DG Loop) - DSTi to DSTo at the PCM24 side. Bit DLBK = 0 normal; DLBK = 1 activate.
MT9072
DSTi System DSTo
Tx
PCM24
b) Payload loopback (PL Loop) - Payload loopback (DSTo to DSTi). Bit PLBK = 0 normal; PLBK = 1 activate. The payload loopback is effectively a physical connection of DSTo to DSTi within the framer. Note: Set RxDO (YF1 bit 9 to 1) to obtain correct data at the Tx.
MT9072
DSTi System DSTo Tx Rx PCM24
c) Local and Remote Timeslot Loopback. Remote timeslot loopback control bit RTSL = 0 normal; RTSL = 1 activate (Register Y90-YA7) will loop around transmit ST-BUS timeslots to the DSTo stream. Local timeslot loopback bits LTSL = 0 normal; LTSL = 1 activate(Register Y90-YA7), will loop around receive PCM24 timeslots towards the remote PCM24 end.
MT9072 System
DSTi DSTo
Tx
PCM24
Rx
d) Framer Remote loopback - Internally connects RPOS and RNEG of one framer to TPOS and TNEG respectively of one of the other integrated framers. Bit RLBK01, RLBK23, RLBK45, RLBK67 = 0 normal; = 1 activate.
MT9072 Framer 0,2,4,6
DSTi System DSTo Tx Rx PCM24 Rx Tx
MT9072 Framer 1,3,5,7
DSTo DSTi System
8Mbit/s mode: Bit RLBK8 = 0 normal; = 1 activate.
SEMICMF.019
73
MT9072
MT9072 Framer 0-3
DSTi[0] System DSTo[0] Tx Rx PCM24 Rx Tx
Data Sheet
MT9072 Framer 4-7
DSTo[4] DSTi[4] System
e) Framer ST-BUS loopback(Register 904) - Internally connects DSTi of one framer to DSTo of one of the other integrated framers. Bit SLBK01, SLBK23, SLBK45, SLBK67 = 0 normal; = 1 activate.
MT9072 Framer 0,2,4,6
Rx PCM24 Tx DSTo DSTi DSTi System DSTo
MT9072 Framer 1,3,5,7
Tx PCM24 Rx
8Mbit/s mode: Bit SLBK8 = 0 normal; = 1 activate.
MT9072 Framer 0-3
Rx PCM24 Tx DSTi[4] DSTo[0] System DSTi[0] DSTo[4]
MT9072 Framer 4-7
Tx PCM24 Rx
Register Address Y05 Y90-YAF 904
Register Loopback Control Per Channel Control Framer Loopback Global Register
Description This register contains the loopbacks within the framer. RTSL and LTSL are per channel loopbacks. This register contains framer to framer loopbacks.
Table 38 - Registers Related to Loopbacks (T1)
11.2
T1 In Band Loopback Codes
T1.403 defines SF mode line loopback activate and deactivate codes. These codes are either a framed or unframed repeating bit sequence of 00001 for activation or 001 for deactivation. The standard goes on to say that these codes will persist for five seconds or more before the loopback action is taken. The MT9072 will detect both framed and unframed line activate and de-activate codes even in the presence of a BER of 3 x 10-3. Line Loopback Disable Detect - LLDD - in the Alarm Status Word (Y10) will be asserted when a repeating 001 pattern (either framed or unframed) has persisted for 48 milliseconds. Line Loopback Enable Detect LLED in the Alarm Status Word will be asserted when a repeating 00001 pattern (either framed or unframed) has persisted for 48 milliseconds. Other loopup and loopdown codes can be selected by writing to Transmit Loop Activate and Loop Deactivate Code registers(Y0D and Y0E).
74
SEMICMF.019
Data Sheet
MT9072
The selection of the expected received loopup and loopdown code is done by writing to registers Receive Loopup Code and Receive Loop Deactivate Code Match registers(Y0F and YF0). Interrupt status bits LLEDI and LLDDI will be set upon detection of inband loopup or loopdown codes respectively. Maskable interrupts can be generated by disabling the mask bits in Receive line status and Timer mask (Y45 bit 5).
Register Address Y02 Y05 Y0D Y0E Y0F YF0 Y10 Y35 Y45
Register Transmit Alarm Control Loopback Control Transmit Loop Activate Code Transmit Loop Deactivate Code Receive Loop Activate Code Match
Description If the SO bit is set, there will be framed loop codes, otherwise they will be unframed. Setting TLU or TLD will cause the transmitter to start sending the appropriate loopup and loopdown code. This register contains the loop activate code which will be sent on the Tx PCM stream when TLU is set. It also contains 2 bits for code length. This register contains the loop deactivate code which will be sent on the Tx PCM stream when TLD is set. It also contains 2 bits for code length. This register contains the loop activate code which will cause an interrupt if received on the RX PCM stream. It also contains 2 bits for code length.
Receive Loop Deactivate This register contains the loop deactivate code which we are looking for Code Match on the RX PCM stream. It also contains 2 bits for code length. Synchronization and Alarm Status Receive Line and Timer Interrupt Status Receive Line and Timer Interrupt Mask LLED and LLDD will be high when their respective loop codes are detected in the match registers. LLEI and LLDI are the interrupts for LLED and LLDD. LLEIM and LLDIM are the masks for LLEI and LLDI.
Table 39 - Registers Related to In Band Loopbacks (T1)
11.3
E1 Loopbacks
In order to meet PRI Layer 1 requirements and to assist in circuit fault sectionalization, the MT9072 has 7 loopback functions. Table 40 specifies the registers related to controlling the different loopbacks.
SEMICMF.019
75
MT9072
Register Address Y01 Y02 Y90 to YAF 904 Register Test, Error and Loopback Control Register Description
Data Sheet
The bits DLBK,RLBK, SLBK and PLBK can be used for digital loopback, remote loopback, ST-BUS and loopback.
Interrupt and IO control register RxDO and RxCO have to one for certain loopbacks to work. Timeslot Control Register Framer Loopback Global Register Local and Remote Timeslot Control Register allows for Timeslot Loopbacks (RTSLand TTSL). Framer to Framer ST-BUS and Remote Loopbacks.
Table 40 - Register Related to Setting Up Loopbacks (E1)
a) Digital loopback (DG Loop) - DSTi to DSTo at the PCM30 side. Bit DLBK = 0 normal; DLBK = 1 activate. The control bits for digital, remote, ST-BUS and payload loopbacks are located at address Y05. The remote and local timeslot loopbacks are controlled through control bits of the Timeslot Control register located at addresses Y90YAF.
MT9072
DSTi System DSTo
Tx
PCM30
b) Payload loopback (PL Loop) - Payload loopback (DSTo to DSTi). Bit PLBK = 0 normal; PLBK = 1 activate. The payload loopback is effectively a physical connection of DSTo to DSTi within the MT9072.
MT9072
System DSTi DSTo Tx Rx PCM30
c) Local and Remote Timeslot Loopback. Remote timeslot loopback control bit RTSL = 0 normal; RTSL = 1 activate, will loop around transmit ST-BUS timeslots to the DSTo stream. Local timeslot loopback bits LTSL = 0 normal; LTSL = 1 activate, will loop around receive PCM30 timeslots towards the remote PCM30 end.
MT9072 System
DSTi DSTo
Tx
PCM30
Rx
d) Framer Remote loopback - Internally connects RPOS and RNEG of one framer to TPOS and TNEG respectively of one of the other integrated framers.
76
SEMICMF.019
Data Sheet
Bit RLBK01, RLBK23, RLBK45, RLBK67 = 0 normal; = 1 activate.
MT9072 Framer 0,2,4,6
DSTi System DSTo Tx Rx PCM30 Rx Tx
MT9072
MT9072 Framer 1,3,5,7
DSTo System DSTi
8Mbit/s mode: Bit RLBK8 = 0 normal; = 1 activate.
MT9072 Framer 0-3
DSTi[0] System DSTo[0] Tx Rx PCM30 Rx Tx
MT9072 Framer 4-7
DSTo[4] DSTi[4] System
e) Framer ST-BUS loopback - Internally connects DSTi of one framer to DSTo of one of the other integrated framers. Bit SLBK01, SLBK23, SLBK45, SLBK67 = 0 normal; = 1 activate.
MT9072 Framer 0,2,4,6
Rx PCM30 Tx DSTo DSTi System DSTi DSTo
MT9072 Framer 1,3,5,7
Tx PCM30 Rx
8Mbit/s mode: Bit SLBK8 = 0 normal; = 1 activate.
MT9072 Framer 0-3
Rx PCM30 Tx DSTi[4] DSTo[0] System DSTi[0] DSTo[4]
MT9072 Framer 4-7
Tx PCM30 Rx
12.0
12.1
Performance Monitoring
T1 Error Counters
The MT9072 has nine error counters for each framer, which can be used for maintenance testing and ongoing measurement of the quality of a DS1 link and to assist the designer in meeting specifications such as TR62411 and T1.403. All counters can be preset or cleared by writing to the appropriate counter registers. Associated with each counter is a maskable event occurrence interrupt and a maskable counter overflow interrupt. Overflow interrupts are useful when cumulative error counts are being recorded. For example, every time the
SEMICMF.019
77
MT9072
Data Sheet
framing bit error counter overflow interrupt (FEO) occurs, 65536 frame errors have been received since the last FEO interrupt. Also if a counter overflows, the overflow indicators are latched in the Overflow reporting latch register(Y24). All counters are cleared by a counter clear bit -CNTCLR - low to high transition (bit 2 of the IO Control Word, YF1). An alternative approach to event reporting is to mask error events and to enable the 1 second sample bit (SAMPLE - bit 1 of the Interrupt and IO Control Word). When this bit is set the latched version of the counters(Y28 to Y2C) for change of frame alignment, loss of frame alignment, bpv errors, crc errors, errored framing bits, and multiframes out of sync are updated on one second intervals coincident with the maskable one second interrupt timer.
.
Counter Description PRBS Error Counter and CRC Multiframe counter for PRBS Multiframe Out of Frame Counter Framing Bit Error Counter BPV Counter CRC-6 Error counter Bits PS7-0, PSM7-0 MFOOF 7-0 FC15-0 BPV15-0 CC15-0
Interrupt Status Bits Address Indication Y15 PRBSI Overflow PRBSOI NA PRBSMFOI
1 Second Latch Description Bit NA Address NA
Y16 Y17 Y18 Y19 Y1A
MFOOFI FBEI BPVI CRCI
MFOOFOI Multiframe Out of Frame Count Latch FEOI BPVOI CRCOI OOFOI COFOIL Framing Bit Error Counter Latch Bipolar Violation Count Latch CRC-6 Error Count Latch
MFOO FL15-0 FCL150 BPVL 15-0 CRCL 15-0
Y2C Y28 Y29 Y2A Y2B
Out of frame counter, OOF7-0, change of frame COFA7-0 alignment counter Excessive Zero counter EXZ7-0,
OOFOI COFAI Y1B EXZI
Out of Frame, Change OOFL of Frame Alignment 7-0 Count Latch COFAL 7-0 NA NA
EXZOL
NA
Table 41 - Error Counters Summary (T1)
12.2
E1 Error Counters
The MT9072 has eight error counters, which can be used for maintenance testing, and ongoing measurement of the quality of a PCM30 link and to assist the designer in meeting specifications such as ITU-T I.431 and G.821. All counters can be preset or cleared by writing to the appropriate locations. In addition, four error count latches are provided which latch the counter data coincident with the one second status bit. Counters can automatically be cleared (ACCLR register address Y03) after their data is latched. Associated with each counter is a maskable event indication interrupt and a maskable counter overflow interrupt. Overflow interrupts are useful when cumulative error counts are being recorded. For example, every time the frame error counter overflow (FEO) interrupt occurs, 256 frame errors have been received since the last FEO interrupt. The interrupt status register bits are cleared when read. All non-latched error counters are cleared and by programming the counter clear bit (CNCLR register address Y03) low to high. See Table 43 for counter events and relationship between the counters.
78
SEMICMF.019
Data Sheet
Register Address Y03 Y15 Y16 Y17 Y18 Register DL,CCS,CAS and other Control Register Description
MT9072
The CNCLR bit can be used to clear the non-latched counters. the ACCLR can be used to automatically clear 1 sec counter.
PRBS Error Counter and CRC- PRBS counts bit errors and the CRC counter interval for each 4 Multiframe Counter received multiframe. Loss of basic frame counter E-bit error counter Bipolar violation counter. This counter counts the bipolar violation outside the HDB3 coding. CRC-4 error counter FAS bit error counter and FAS error counter E bit error counter latch BPV error counter latch CRC-4 error counter latch FAS error counter latch CAS,National, CRC-4 local and timer interrupt status register CAS,National, CRC-4 local and timer interrupt mask register Counter that is incremented once per 125 usec whenever bsync is 1. This counter counts the ebit errors. This counter counts the bipolar violation outside the HDB3 coded zeros.
Y19 Y1A Y28 Y29 Y2A Y2B Y36
This counter is incremented for calculated crc-4 errors (CRCS1 and CRCS2). This counter counts the FAS bit error and FAS errors. This counter is the one second latched version of Y17. This counter is a one second latched version of Y18. This counter is a one second latched version of Y19. This counter is a one second latched version of Y1A. Oneseci is the one second interrupt status. This interrupt can be used for performance monitoring. Onesecm is the one second interrupt status. This interrupt can be used for performance monitoring.
Y46
Table 42 - Registers Required for Observing and Clearing Error Counters (E1)
SEMICMF.019
79
MT9072
Counter Description PRBS Error Counter PRBS CRC-4 MF Counter Loss of Sync Counter E-bit Error Counter BPV Error Counter CRC-4 Error Counter FAS Bit Error Counter FAS Error Counter Bits PEC7-0 PCC7-0 SLC7-0 EEC15-0 VEC15-0 CEC15-0 BEC7-0 FEC7-0 Address Y15 Y15 Y16 Y17 Y18 Y19 Y1A Y1A CRCS1 CRCS2 CALN BSYNC REB1 REB2 Source Interrupt Status Bits Bit Indication Overflow PEI NA BSYNC EEI VEI CEI BEI FEI PEO PCO SLO EEO VEO CEO BEO FEO
Data Sheet
1 Second Latch Description NA NA NA E-bit Error Count Latch BPV Error Count Latch CRC-4 Error Count Latch FAS Bit Error Count Latch FAS Error Count Latch Bit NA NA NA EEL15-0 VEL15-0 CEL15-0 BEL7-0 FEL7-0 Address NA NA NA Y28 Y29 Y2A Y2B Y2B
Table 43 - Error Counter and Event Dependency (E1)
13.0
13.1 13.1.1
Maintenance and Alarms
T1 Maintenance and Alarms T1 Error Insertion
Six types of error conditions can be inserted into the transmit DS1 data stream through control bits, which are located in address Y03 -Transmit Error Control Word. These error events include bipolar violation errors (BPVE), CRC-6 errors (CRCE), Ft errors (FTE), Fs errors (FSE), payload errors (PERR) and a loss of signal condition (LOSE). If LOSE is one the selected framer transmits an all zeros signal (no pulses) and zero code suppression is overridden. If LOSE bit is zero, data is transmitted normally.
13.1.2
T1 Per Timeslot Control
There are 24 per timeslot control registers occupying a total of 24 unique addresses (Y90-YA7). Each register controls a transmit timeslot and the equivalent channel data on DSTo. For example, register address Y90 of the first per timeslot control register contains program control for transmit timeslot 0 and DSTo channel 0.
13.1.3
T1 Per Timeslot Looping
Any channel or combination of channels may be looped from transmit (sourced from DSTi) to receive (output on DSTo) ST-BUS channels. When bit 4 (LTSL) in the Per Timeslot Control Word(Y90-YA7) is set the data from the equivalent transmit channel is looped back onto the equivalent receive timeslot. Any channel or combination of channels may be looped from receive (sourced from the line data) to transmit (output onto the line) channels. When bit 5 (RTSL) in the Per Timeslot Control Word is set the data from the equivalent receive timeslot is looped back onto the equivalent transmit timeslot.
13.1.4
80
T1 Pseudo-Random Bit Sequence (PRBS) Testing
SEMICMF.019
Data Sheet
MT9072
The MT9072 includes both a pseudo random bit sequence (PRBS) generator of type (215-1), and a reverse PRBS generator (decoder), which operates on a bit sequence, and determines if it matches the transmitted PRBS type (215-1). Bits which don't match are counted by an internal error counter. This provides for powerful system debugging and testing without additional external hardware. If control bit ADSEQ (register address Y01) is zero, any transmit (internal DSTi) timeslot or combination of transmit timeslots may be connected to the PRBS generator. Timeslot n is selected by setting the TTSTn bit in the Timeslot n Control Register (address Y90-YA7), where n is 0 to 23. Any data sent on DSTi is overwritten on the selected timeslots before being output to TPOS/TNEG. Similarly, if control bit ADSEQ is zero, any receive timeslot or combination of receive timeslots may be connected to the PRBS decoder. Timeslot n is selected by setting the RRSTn bit in the Timeslot n Control Register (register address Y90-YA7), where n is 0 to 23. PRBS data is distributed to the transmit channels sequentially one byte at a time. Consequently, the data received must be in the same order that it was sent, in order for the PRBS decoder to correctly operate on the data. If one channel is tested at a time, then the PRBS transmit timeslot does not have to match the PRBS receive timeslot. However, if more than one channel is tested, then the number of transmit timeslots must match the number of receive timeslots, and the order of the transmit timeslots must match the order of the receive timeslots. This will ensure that the sequential data bytes received by the PRBS decoder are in the correct order. Consequently, particular care must be taken when using an external loopback where the channel order may be reversed, or where the data has passed through a digital switch which doesn't buffer all channels to the same degree. The PRBS decoder must have sufficient data pass through it before it begins to operate correctly, therefore, the errors generated by the decoder immediately following start-up should be ignored. If the PRBS testing is performed in an external loop around using Timeslot Control, then both Timeslot Control bits TTSTn and RRSTn should also be set.
Register Address Y01 Y90-YA7
Register Line Interface and Coding Per Channel Control
Description ADSEQ bit chooses between Milliwatt test sequence and transmitted PRBS test sequence. If TTST is set for any channel, the test sequence will be transmitted on that DS1 timeslot. If RRST is set for any channel, the test sequence will be expected on the receivePCM24 slot.
Y15 Y34 Y44
PRBS Error Counter and CRC The PRBS Error Counter contains error count on the received Multiframe Counter for PRBS PRBS sequence. Receive Sync Interrupt Status Receive Sync Interrupt Mask PRBSOI will indicate an overflow on the PRBS Error Counter. PRBSOIM is the mask for PRBSOI.
Table 44 - Registers Related to PRBS Testing (T1)
13.1.5
T1 Mu-law Milliwatt
If the control bit ADSEQ is one (register address Y01), the Mu-law digital milliwatt sequence (Table 45) defined by G.711, is available to be transmit on any combination of selected channels. The channels are selected by setting the TTSTn control bit (register address Y90-YA7). The same sequence is available to replace received data on any combination of DSTo channels. This is accomplished by setting the RRSTn control bit (register address Y90-YA7) for the corresponding channel. Note that Bit 1 is the sign bit and is sent first.
SEMICMF.019
81
MT9072
PCM 24 Payload Data Hex 1E 0B 0B 1E 1E 8B 8B 9E Bit 1 0 0 0 0 1 1 1 1 Bit 2 0 0 0 0 0 0 0 0 Bit 3 0 0 0 0 0 0 0 0 Bit 4 1 0 0 1 1 0 0 1 Bit 5 1 1 1 1 1 1 1 1 Bit 6 1 0 0 1 1 0 0 1
Data Sheet
Bit 7 1 1 1 1 1 1 1 1
Bit 8 0 1 1 0 0 1 1 0
Table 45 - Mu Law Digital Milliwatt Pattern (T1)
13.1.6
T1 Alarms
The alarms shown in Table 46 are detected by the receiver. The status register bits provide real time status of the alarm, while the interrupt status registers bits provide latched status indications which are cleared when read. Each interrupt status register may also generate a maskable interrupt. The possible transmitted alarms are also shown in the table. See the register bit descriptions for details.
Control/Status Register Description D4 Yellow Alarm. This bit is set if bit position 2 of virtually every DS0 channel is a zero for a period of 600 milliseconds. The alarm is tolerant of errors by permitting up to 16 ones in a 48 millisecond integration period. The alarm clears in 200 milliseconds after being removed from the line. D4 Yellow Alarm - 48 millisecond sample. This bit is set if bit position 2 of virtually every DS0 channel is a zero for a period of 48 milliseconds. The alarm is tolerant of errors by permitting up to 16 ones in the integration period. This bit is updated every 48 milliseconds. Secondary D4 Yellow Alarm. This bit is set if 2 consecutive'1's are received in the S-bit position of the 12th frame of the D4 superframe. AIS Alarm. This bit is set if fewer than 5 zeros are received in a 3 millisecond window. ESFYEL.This bit is set if the ESF yellow alarm 0000000011111111 is receive in eight or more codewords out of ten in Bit Oriented Message of FDL. Bit D4YALM Address Y10
Interrupt Status Register Bit D4YALMI Address Y35
D4Y48
Y10
D4Y48I
Y35
SECYEL
Y10
SECYELI
Y35
AIS ESFYEL
Y10 Y10
AISI ESFYELI
Y35 Y35
Table 46 - Alarm Control and Status Bits (T1)
82
SEMICMF.019
Data Sheet
Control/Status Register Description T1DM Received Yellow Alarm. If "Y" bit of the T1DM Synchronization Word is received Transmit ESF Yellow Alarm. Setting this bit (while in ESF mode) causes a repeating pattern of eight 1's followed by eight 0's to be insert onto the transmit FDL. Transmit Secondary D4 Yellow Alarm. Setting this bit (in D4 mode) causes the S-bit of transmit frame 12 to be set. Transmit All Ones. When low, this control bit forces a framed or unframed (depending on the state of Transmit Alarm Control bit 0) all ones to be transmit at TTIP and TRING S-bit Override. If set, this bit forces the S-bits to be inserted as an overlay on any of the following alarm conditions: i) transmit all ones, ii) loop up code insertion, iii) loop down code insertion. TT1DMY. If reset to low a yellow alarm is sent in the 24th channel if the T1DM option is set. Bit T1DRY TESFYEL Address Y10 Y02
MT9072
Interrupt Status Register Bit T1DMYI NA Address Y35 NA
TSECY TAIS
Y02 Y02
NA NA
NA NA
SO
Y02
NA
NA
TT1DMY
Y02
NA
NA
Table 46 - Alarm Control and Status Bits (T1)
13.1.7
T1 Per Timeslot Trunk Conditioning
The per channel conditioning capabilities of MT9072 are explained in this section. For the receiver the T1 data can be replaced by the conditioning data (Y09) via the bit MPDR in the per channel control registers(Y90 to YA7). This data will be output to the corresponding DSTo channel. The received data can be inverted on a per channel basis by setting the RPCI bit (register Y90 to YA7). The transmit data can be inverted on a per channel basis with a write to the control bit TPCI (registers Y90 to YA7). The transmit data can also be frozen on a per channel basis; in this case the data from the DSTI is not used to update the Transmit Memory and the data written in Y0A is used as the source (MPDT in registers Y90 to YA7).
13.2
E1 Maintenance and Alarms
Extensive maintenance and alarm generation and detection functions are provided on the MT9072. The following table groups the registers for control and monitor of these functions.
Register Address Y00 Y01 Y05 Y10
Register
Description
Alarm and Framing Control Register The TAIS and E bit errors and RAI can be set by this register. Test Error and Loopback Control Register CAS Control and Data Register Synchronization and CRC-4 Remote Status BPVE, CRCE,FASE, NFSE and E bit errors can be inserted. The Y bit can be used to send Remote Multiframe Alarm signal. The bits of this register provide good receiver error status.
Table 47 - Registers Related to Maintenance and Alarms (E1)
83
SEMICMF.019
MT9072
Register Address Y11 Y12 Y24 Y34 Y44 Register CRC-4 Timer and CRC-4 Local Status Alarms and MAS Status Sync, CRC-4 remote alarm, MAS Latched Status Register Sync, CRC-4 Remote Alarm, MAS Interrupt status register Sync, CRC-4 Remote Alarm, MAS Interrupt register mask Description The CRC-4 errors are registered in Y11.
Data Sheet
This register provides AIS, RAI, LOSS status bits. Latched version of receive CRC errors and synchronization loss are available. This register provides bits for interrupt generation for Y24 CRC errors and synchronization loss functions. This register provides bits for interrupt mask register for Y34.
Table 47 - Registers Related to Maintenance and Alarms (E1)
13.2.1
E1 Error Insertion
Six types of error conditions can be inserted into the transmit PCM30 data stream through register control bits located at address Y01. These error events include the bipolar violation errors (BVE), CRC-4 errors (CRCE), FAS errors (FASE), NFAS errors (NFSE), payload (PERR) and a loss of signal error (LOSE). The LOSE function overrides the HDB3 encoding function (no BPV are added). Also included are E1 and E2 error bit insertion on frames 13 and 15. See the bit descriptions (control register address Y01) for additional details.
13.2.2
E1 Per Timeslot Control
There are 32 per timeslot control registers occupying a total of 32 unique addresses (Y90-YAF). Each register controls a matching timeslot on the 32 transmit channels (onto the line) and the equivalent channel data on the receive (DSTo) data. For example, register address Y91 of the first per timeslot control register contains program control for transmit timeslot 1 and DSTo channel 1.
13.2.3
E1 Per Timeslot Looping
Any channel or combination of channels may be looped from transmit (sourced from DSTi) to receive (output on DSTo) ST-BUS channels. When bit 4 (LTSL) in the Per Timeslot Control Word is set the data from the equivalent transmit timeslot is looped back onto the equivalent receive channel. Any channel or combination of channels may be looped from receive (sourced from the line data) to transmit (output onto the line) channels. When bit 5 (RTSL) in the Per Timeslot Control Word is set the data from the equivalent receive timeslot is looped back onto the equivalent transmit channel.
13.2.4
E1 Pseudo-Random Bit Sequence (PRBS) Testing
The MT9072 includes both a pseudo random bit sequence (PRBS) generator of type (215-1), and a reverse PRBS generator (decoder), which operates on a bit sequence, and determines if it matches the transmitted PRBS type (215-1). Bits which don't match are counted by an internal error counter. This provides for powerful system debugging and testing without additional external hardware. If control bit ADSEQ (register address Y01) is zero, any transmit (internal DSTi) timeslot or combination of transmit timeslots may be connected to the PRBS generator. Timeslot n is selected by setting the TTSTn bit in the Timeslot n Control Register (address Y90-YAF), where n is 0 to 31. Any data sent on DSTi is overwritten on the selected timeslots. Similarly, if control bit ADSEQ is zero, any DSTo receive timeslot or combination of receive timeslots may be connected to the PRBS decoder. Timeslot n is selected by setting the RRSTn bit in the Timeslot n Control Register
84
SEMICMF.019
Data Sheet
(register address Y90-YAF), where n is 0 to 31. Data on DSTo is not affected.
MT9072
PRBS data is distributed to the transmit channels sequentially one byte at a time. Consequently, the data received must be in the same order that it was sent, in order for the PRBS decoder to correctly operate on the data.
The number of transmit timeslots must match the number of receive timeslots, and the order of the transmit timeslots must match the order of the receive timeslots. This will ensure that the sequential data bytes received by the PRBS decoder are in the correct order. Consequently, particular care must be taken when using an external loopback where the channel order may be reversed, or where the data has passed through a digital switch which doesn't buffer all channels to the same degree. The PRBS decoder must have sufficient data pass through it before it begins to operate correctly, therefore, the errors generated by the decoder immediately following start-up should be ignored. If the PRBS testing is performed in an external loop around using Timeslot Control, then both Timeslot Control bits TTSTn and RRSTn should also be set.
13.2.5
E1 A-law Milliwatt
If the control bit ADSEQ is one (register address Y01), the A-law digital milliwatt sequence (Table 48), defined by G.711, is available to be transmit on any combination of selected channels. The channels are selected by setting the TTSTn control bit (register address Y90-YAF). The same sequence is available to replace received data on any combination of DSTo channels. This is accomplished by setting the RRSTn control bit (register address Y90-YAF) for the corresponding channel. Note that bit 1 is the sign bit and is sent first.
PCM30 Payload Data Hex 34 21 21 34 B4 A1 A1 B4 Bit 1 0 0 0 0 1 1 1 1 Bit 2 0 0 0 0 0 0 0 0 Bit 3 1 1 1 1 1 1 1 1 Bit 4 1 0 0 1 1 0 0 1 Bit 5 0 0 0 0 0 0 0 0 Bit 6 1 0 0 1 1 0 0 1 Bit 7 0 0 0 0 0 0 0 0 Bit 8 0 1 1 0 0 1 1 0
Table 48 - A-Law Digital Milliwatt Pattern (E1)
13.2.6
E1 Alarms
The alarms shown in Table 49 are detected by the receiver. The status register bits provide real time status of the alarm, while the latched status registers provide a latched status indication, and the interrupt status registers provide a latched status indication (if unmasked) which generate a maskable interrupt and which are cleared when read. The persistent status registers provide latched status indication which is only cleared when read while the real time status bit is not set. See the register bit descriptions for additional details.
SEMICMF.019
85
MT9072
Description Status Register Bit Remote Alarm Indication Alarm Indication Signal Alarm Indication Signal 100ms Channel 16 Alarm Indication Signal Auxiliary Pattern Loss of Signal Remote signaling Multiframe Alarm T1 Timer T2 Timer RAI AIS KLVE AIS16 AUXP LOSS Y T1 T2 Add. Y12 Y12 Y12 Y12 Y12 Y12 Y12 Y11 Y11 AIS16L AUXPL LOSSL YL T1L T2L Y24 Y24 Y24 Y24 Y26 Y26 AIS16I AUXPI LOSSI YI T1I T2I Y34 Y34 Y34 Y34 Y36 Y36 Latched Status Register Bit RAIL AISL Add. Y24 Y24 Interrupt Status Register Bit RAII AISI Add. Y34 Y34
Data Sheet
Persistent Status Register Bit RAIP AISP Add. Y27 Y27
LOSSP
Y27
Table 49 - Alarms and Timers Status Registers (E1)
13.2.7
E1 Automatic Alarms
The transmission of RAI and signaling multiframe alarms can be made to function automatically from control bits ARAI and AUTY (register address Y00). When ARAI = 0 and basic frame synchronization is lost (BSYNC = 1 address Y10), the MT9072 will automatically transmit the RAI alarm signal to the far end of the link. The transmission of this alarm signal will cease when basic frame alignment is acquired. When AUTY = 0 and signaling multiframe alignment is not acquired (MSYNC = 1 address Y10), the MT9072 will automatically transmit the multiframe alarm (Y-bit) signal to the far end of the link. This transmission will cease when signaling multiframe alignment is acquired.
14.0
Interrupts
The MT9072 has an extensive suite of interrupts consisting of 2 maskable interrupt vectors and 32 maskable interrupt status registers as shown in Figure 9 and an ST-BUS Analyzer Interrupt. The set bits in the 2 interrupt vectors identify which of the 32 interrupt status registers is responsible for the interrupt. Reading the corresponding interrupt status registers identifies the exact source of the interrupt. Any set bit in the interrupt vectors causes the IRQ pin to toggle low (providing the SPND bit is not set).
86
SEMICMF.019
Data Sheet
MT9072
Interrupt Vector 2
Interrupt Vector 1
IRQ 2
4 Interrupt Vector 2 Status Register Address 911 4 Interrupt Vector 2 Mask Register Address 903
4
4
4
Interrupt Vector 1 Status Register Address 910 4 4 4 IRQ 1
Interrupt Vector 1 Mask Register Address 902
IRQ Pin
4
4
4
4
ST-BUS Analyser Interrupt
HDLC Status Register 033
Rx Sync Interrupt Status Register 034 Rx Sync Mask Status Register 044
Rx Line Status Register 035
Elastic Interrupt Status Register 036 Elastic Store Mask Status 046
HDLC Mask Status Register 043
RX Line Mask Status Register 045
F R A M E R 7
F R A M E R 6
F R A M E R 5
F R A M E R 4
F R A M E R 3
F R A M E R 2
F R A M E R 1
Framer 0 Master LatchStatus Registers 023 - 026
INTA
FRAMER 0
SPND
Figure 9 - Interrupt Status Registers
14.1
Interrupt Status Register Overview
All 33 interrupt status registers are maskable with 33 corresponding interrupt mask registers. All interrupt status registers and all interrupt mask registers are 16 bits, although all 16 bits are not always used. Unused status bits may be either one or zero if read. When an unmasked interrupt occurs, one or more bits of the 33 interrupt status registers will go high causing one
SEMICMF.019
87
MT9072
Data Sheet
or more bits of the unmasked interrupt vector to go high. A high bit in the interrupt vector causes the output IRQ pin to go low (if enabled by SPND, INTA control bits). After an interrupt status register is read, it is automatically cleared. After all interrupt status registers are cleared, the interrupt vector is cleared causing the IRQ pin to return to a high impedance state. If a new unmasked interrupt occurs while the interrupt status registers from a previous interrupt are being read, the affected interrupt status registers will be updated, the interrupt vector will be updated, and the IRQ pin will remain low until all interrupt status registers are cleared. If the interrupt status registers are unmasked, and the interrupt vector is masked, the interrupt status registers will function normally, but they will not cause the IRQ pin to toggle low. Only set bits in the Interrupt Vector will cause the IRQ pin to toggle low. This is similar to the SPND control bit function, but instead of masking all selected framer interrupts, the interrupt vector mask can mask individual registers within the selected framers.
14.1.1
Interrupt Related Control Bits and Pins
SPND - All interrupts for a particular framer may be suspended without changing the interrupt mask words, by setting the SPND control bit (register address YF1) to zero. All unmasked interrupt status registers will continue to be updated (and will be cleared when read), but the selected framers interrupt vector bits will remain at zero. Therefore that framer cannot toggle the IRQ pin. If all eight framer's SPND bit are zero, then all interrupt vector bits will remain low, therefore none of the framers can toggle the IRQ pin. In some applications, a logic low at the IRQ pin lasting the full duration of the interrupt service routine may be undesirable. In these cases, immediately following the interrupt, set the control bit SPND (register address YF1) low until the interrupt service routine is finished INTA - All interrupt and latched status registers for a particular framer may be cleared (without reading the interrupt status registers) by setting the INTA control bit (register address YF1) to zero. Interrupt status and latched registers for a particular framer will be cleared (and not updated) as long as INTA is low. Consequently, the selected framer's interrupt vector bits will remain at zero, therefore that framer cannot toggle the IRQ pin. TAIS - During initial power up, all (8 framers) interrupt status registers are cleared without changing the interrupt mask words, when the TAIS control pin is held low. Consequently, the interrupt vector will remain clear and the IRQ pin will remain in a high impedance state. This allows for system initialization without spurious interrupts. Interrupt status registers will not be updated, and the IRQ pin will be forced to a high impedance state as long as TAIS is low. RESET or RST - After a MT9072 reset (RESET pin for all eight framers or RST control bit (register address YF1) for a selected framer), all interrupt status register bits are unmasked, but the SPND and INTA control bits are set to zero.
14.2
Interrupt Servicing Methods
There are two common methods for identifying the source of an interrupt. The Polling Method is the simplest but uses the most processor time. The Vector Method requires a two step process, but uses the least amount of processor time.
14.2.1
Polling Method
1. The IRQ pin goes low. 2. Read all 33 interrupt vector status registers. The bits which are set in these registers identify the source of the interrupt. As each register is read, it is cleared (all bits set to 0). When all registers are clear, the interrupt is cleared (the IRQ pin returns to logic high) and all sources of the interrupt are identified.
14.2.2
Vector Method
1. The IRQ pin goes low.
88
SEMICMF.019
Data Sheet
MT9072
2. Read the interrupt vectors. These vectors identify which of the 33 (or which combination of 33) interrupt status registers has bits which are set. Note that if multiple framers (i.e. Framer 1 and 7), or multiple conditions (i.e. Sync and Counter Overflow) caused the interrupt, more than one register may need to be read. 3. Read the interrupt status register(s) identified in step 2. The bits which are set in these registers identify the source of the interrupt. As each register is read, it is cleared (all bits set to 0). When all interrupt status registers are cleared, the interrupt vector goes to zero and the IRQ pin returns to logic high.
14.3
T1 Interrupt Vector and Interrupt Source Summary
Interrupt Vector Address Bit Name 911 911 911 911 911 911 911 911 911 911 911 911 911 911 911 911 911 910 910 910 910 910 910 F7HVS F7EVS F7RVS F7SVS F6HVS F6EVS F6RVS F6SVS F5HVS F5EVS F5RVS F5SVS F4HVS F4EVS F4RVS F4SVS F3HVS F3EVS F3RVS F3SVS F2HVS F2EVS F2RVS
Interrupt Vector Mask Address 903 903 903 903 903 903 903 903 903 903 903 903 903 903 903 903 902 902 902 902 902 902 902 Bit Name F7HM F7EM F7RM F7SM F6HM F6EM F6RM F6SM F5HM F5EM F5RM F5SM F4HM F4EM F4RM F4SM F3HM F3EM F3RM F3SM F2HM F2EM F2RM
Interrupt Registers Status Address 733 734 735 736 633 634 635 636 533 534 535 536 433 434 435 436 333 334 335 336 233 234 235 Mask Address 743 744 745 746 643 644 645 646 543 544 545 546 443 444 445 446 343 344 345 346 243 244 245 Register Name HDLC Receive Sync Receive Line Elastic store HDLC Receive Sync Receive Line Elastic HDLC Receive Sync Receive Line Elastic HDLC Receive Sync Receive Line Elastic HDLC Receive Sync Receive Line Elastic store HDLC Receive Sync Receive Line Framer 7 7 7 7 6 6 6 6 5 5 5 5 4 4 4 4 3 3 3 3 2 2 2
Table 50 - Interrupt Vector and Interrupt Source Summary (T1)
SEMICMF.019
89
MT9072
Interrupt Vector Address Bit Name 910 910 910 910 910 910 910 910 910 F2SVS F1HVS F1EVS F1RVS F1SVS F0HVS F0EVS F0RVS F0SVS Interrupt Vector Mask Address 902 902 902 902 902 902 902 902 902 Bit Name F2SM F1HM F1EM F1RM F1SM F0HM F0EM F0RM F0SM Interrupt Registers Status Address 236 133 134 135 136 033 034 035 036 Mask Address 246 143 144 145 146 043 044 045 046
Data Sheet
Register Name Elastic HDLC Receive Sync Receive Line Elastic HDLC Receive Sync Receive Line Elastic
Framer 2 1 1 1 1 0 0 0 0
Table 50 - Interrupt Vector and Interrupt Source Summary (T1)
14.4
E1 Interrupt Vector and Interrupt Source Summary
Interrupt Vector Address 911 911 911 911 911 911 911 911 911 911 911 911 911 Bit Name F7HI F7NI F7CI F7SI F6HI F6NI F6CI F6SI F5HI F5NI F5CI F5SI F4HI
Interrupt Vector Mask Address Bit Name 903 903 903 903 903 903 903 903 903 903 903 903 903 F7HM F7NM F7CM F7SM F6HM F6NM F6CM F6SM F5HM F5NM F5CM F5SM F4HM
Latch Status, Interrupt Status and Interrupt Mask Register Source Latch Address 723 724 725 726 723 724 725 726 523 524 525 526 423 Status Address 733 734 735 736 633 634 635 636 533 534 535 536 433 Mask Address 743 744 745 746 643 644 645 646 543 544 545 546 443 Register Name HDLC National Counter Sync HDLC National Counter Sync HDLC National Counter Sync HDLC Framer 7 7 7 7 6 6 6 6 5 5 5 5 4
Table 51 - Interrupt Vector and Interrupt Source Summary (E1)
90
SEMICMF.019
Data Sheet
Interrupt Vector Address 911 911 911 910 910 910 910 910 910 910 910 910 910 910 910 910 910 910 910 Bit Name F4NI F4CI F4SI F3HI F3NI F3CI F3SI F2HI F2NI F2CI F2SI F1HI F1NI F1CI F1SI F0HI F0NI F0CI F0SI Interrupt Vector Mask Address Bit Name 903 903 903 902 902 902 902 902 902 902 902 902 902 902 902 902 902 902 902 F4NM F4CM F4SM F3HM F3NM F3CM F3SM F2HM F2NM F2CM F2SM F1HM F1NM F1CM F1SM F0HM F0NM F0CM F0SM
MT9072
Latch Status, Interrupt Status and Interrupt Mask Register Source Latch Address 424 425 426 323 324 325 326 223 224 225 226 123 124 125 126 023 024 025 026 Status Address 434 435 436 333 334 335 336 233 234 235 236 133 134 135 136 033 034 035 036 Mask Address 444 445 446 343 344 345 346 243 244 245 246 143 144 145 146 043 044 045 046 Register Name National Counter Sync HDLC National Counter Sync HDLC National Counter Sync HDLC National Counter Sync HDLC National Counter Sync Framer 4 4 4 3 3 3 3 2 2 2 2 1 1 1 1 0 0 0 0
Table 51 - Interrupt Vector and Interrupt Source Summary (E1)
SEMICMF.019
91
MT9072
14.5 E1 Interrupt Source and Interrupt Status Register Summary
Interrupt Status Register Interrupt Description Real Time Source Status Register or PCM30
Data Sheet
Address Bit Name Address Bit Name Y10 Y10 Y12 Y12 Y12 Y12 Y12 Y12 Y10 Y10 Y10 Y10 Y10 Y10 Y10 RCRCR RSLP Y
AUXP
Y34 Y34 Y34 Y34 Y34 Y34 Y34 Y34 Y34 Y34 Y34 Y34 Y34 Y34 Y34
RCRCRI RSLPI YI
AUXPI
remote CRC-4 and RAI occurred receive slip occurred remote multiframe sync fail occurred
auxiliary pattern occurred
RAI
AIS AIS16 LOSS RCRC0 RCRC1
RAII
AISI AIS16I LOSSI RCRC0I RCRC1I CEFSI RFAILI
S Y N C
remote alarm occurred
alarm indication signal occurred alarm indication signal on channel 16 occurred loss of signal occurred remote CRC-4 sync and RAI for10ms and up occurred remote CRC-4 sync and RAI for 10ms to 450ms occurred consecutive errored FAS's occurred remote CRC-4 multiframe generator/detector failure occurred
CEFS RFAIL CSYNC MSYNC BSYNC
CSYNCI MSYNCI BSYNCI
loss of CRC-4 sync occurred loss of multiframe sync occurred loss of basic frame sync occurred
Table 52 - Interrupt Source & Status Register Summary (E1)
92
SEMICMF.019
Data Sheet
Real Time Source Status Register or PCM30 Interrupt Status Register Interrupt Description
MT9072
Address Bit Name Address Bit Name Y16 Y1A Y1A Y1A Y1A Y19 Y19 Y18 Y18 Y17 Y17 Y15 Y15 Y15 PCM30 PCM30 PCM30 PCM30 PCM30 PCM30 PCM30 PCM30 PCM30 PCM30 Y70-Y8F Y11 Y11 Y11 SL15-0 FEC7-0 FEC7-0 BEC7-0 BEC7-0 CEC15-0 CEC15-0 VEC15-0 VEC15-0 EEC15-0 EEC15-0 PCC7-0 PEC7-0 PEC7-0 Sa5 Sa6 Sa6 Sa6 Sa6 Sa6 Sa6 Sa5-8 Sa5 Sa5-8 ABCD
CALN
Y35 Y35 Y35 Y35 Y35 Y35 Y35 Y35 Y35 Y35 Y35 Y35 Y35 Y35 Y36 Y36 Y36 Y36 Y36 Y36 Y36 Y36 Y36 Y36 Y36 Y36 Y36 Y36 Y36
SLOI FEOI FEII
loss of basic frame sync counter overflowed frame alignment signal (FAS) error counter overflowed frame alignment signal (FAS) error occurred
BEOI
BEII CEOI CEII VEOI VEII EEOI EEII
C O U N T E R
frame alignment signal (FAS)
bit error counter overflowed
frame alignment signal (FAS) bit error occurred CRC-4 error counter overflowed CRC-4 error occurred bipolar violation error counter overflowed bipolar violation error occurred E-bit error counter overflowed E-bit error occurred
PCOI PEOI
PEII Sa5VI Sa6V3I Sa6V2I Sa6V1I Sa6V0I Sa6N8I Sa6NI
PRBS CRC-4 multiframe counter overflowed PRBS error counter overflowed
PRBS error occurred Sa5 bit value was one when Sa6N8 toggled Sa6 bit 3 value was one when Sa6N8 toggled Sa6 bit 2 value was one when Sa6N8 toggled
from zero to one from zero to one from zero to one from zero to one from zero to one
SaNI
Sa5TI
N A T I O N A L
Sa6 bit 1 value was one when Sa6N8 toggled Sa6 bit 0 value was one when Sa6N8 toggled
sequence of 8 identical Sa6 nibbles occurred Sa6 nibble changed
Sa5,6,7 or 8 nibble changed
Sa5 bit changed
SaTI
CASRI CALNI
Sa5,6,7 or 8 bits changed
receive CAS bit (ABCD) changed CRC-4 2ms timer toggled
T2 T1
T2I T1I
ONESECI
CRC-4 10ms timer toggled from zero to one CRC-4 100ms timer toggled from zero to one
1s timer toggled from zero to one
Table 52 - Interrupt Source & Status Register Summary (E1)
SEMICMF.019
93
MT9072
15.0 JTAG (Joint Test Action Group) Operation
Data Sheet
The MT9072 JTAG (Joint Test Action Group) interface conforms to the Boundary-Scan standard IEEE1149.1-1990. This standard specifies a design-for-testability technique called Boundary-Scan test (BST). Figure 10 shows the BST architecture which is made up of the following four basic elements. See Figure 30 for JTAG timing. 1. Test Access Port (TAP) 2. TAP Controller 3. Instruction Register (IR) 4. Test Data Registers (TDR)
TDO TAP TDI Instruction Register
TMS TCK TRST
TAP Controller
Test Data Registers Device ID Register
Bypass Register
Framer Input Pins
Boundary Scan Register
Framer Output Pins
Framer Core Logic
Figure 10 - Boundary Scan Test Circuit Block Diagram
15.1
Test Access Port (TAP)
The Test Access Port (TAP) provides access to the many test functions of the MT9072. It consists of four input pins and one output pin. The following pins are from the TAP. Test Clock Input (TCK) - TCK provides the clock for the test logic. The TCK signal does not interfere with any onchip clocks and thus remains independent. The TCK permits shifting of test data into or out of the Boundary-Scan register cells concurrently with the operation of the device and without interfering with the on-chip logic. Test Mode Select Input (TMS) - The logic signals received at the TMS input are interpreted by the TAP Controller to control the test operations. The TMS signal is sampled at the rising edge of the TCK pulses. This pin is internally pulled up to device VDD when it is not driven from an external source. Test Data Input (TDI) - Serial input data applied to this port is fed either into the instruction register or into a test data register, depending on the sequence previously applied to the TMS input. Both registers are described in a subsequent section. The received input data is sampled at the rising edge of TCK pulses. This pin is internally pulled
94
SEMICMF.019
Data Sheet
up to device VDD when it is not driven from an external source.
MT9072
Test Data Output (TDO) - Depending on the sequence previously applied to the TMS input, the contents of either the instruction register or data register are serially shifted out towards the TDO pin. The data out of TDO is clocked on the falling edge of the TCK pulses. When no data is shifted through the boundary scan cells, the TDO driver is set to a high impedance state. Test Reset (TRST) - Reset the JTAG scan structure.
15.2
Test Access Port (TAP) Controller
The TAP Controller generates clock and control signals for the Instruction Register (IR) and the Test Data Registers (TDR's). The TAP Controller operates synchronously with the TCK input clock and responds to the TMS input signal to generate control signals which shift, capture, or update data through either the IR or the TDR's.
15.3
Instruction Register
The Instruction Register (IR) is a 3-bit register which allows one of four test instructions to be shifted into the device. Test instructions are serially loaded into the IR from the TDI pin by the TAP Controller. Refer to Table 53 which describes the test instructions provided by the MT9072; these instructions are in accordance with the IEEE 1149.1 standard.
MSB 0 0
LSB 0
Instruction Name EXTEST
Functional Description This instruction isolates the framer logic (on chip logic) from the input and output pins. The signal states at the output pins are determined by the values programmed (earlier) in the Boundary Scan Register. This instruction allows testing of board level interconnects (i.e. open, stuck at, bridge).
0
1
0
SAMPLE/PR This instruction performs two functions. On the rising edge of TCK, the SAMPLE ELOAD instruction is performed. With this instruction, the signal states at the input and output pins are loaded into the Boundary Scan Register. On the falling edge of TCK, the PRELOAD instruction is performed. With this instruction, the signal states at the output pins is determined by the values programmed (earlier) in the Boundary Scan Register. IDCODE This instruction forces the value of the 32 bit MT9072 Identification Register into the Instruction Register's parallel output latches. This is the default instruction loaded after a JTAG reset. This instruction connects the Bypass Register between the TDI and TDO pins.
0
0
1
1
1
1
BYPASS
Note 1. The following optional JTAG instructions are not supported, INTEST, RUNBIST and USERCODE. Table 53 - JTAG Instruction Register
SEMICMF.019
95
MT9072
15.4 JTAG Data Registers
Data Sheet
As specified in IEEE 1149.1, the JTAG Interface must contain as a minimum the boundary scan register and the bypass register. The device identification register although optional, is also included in the MT9072.
15.4.1
Identification Register
This is a 32 bit register as defined in Table 54. Note that the part number revision is not the same as the silicon revision which is not supplied. Version (4 bits) A 0000 0 Part Number (16 bits) 9072 1001 0000 0111 0010 9072 0907214B Table 54 - JTAG MT9072 Identification Register Manufacturer Identity (11 bits) Zarlink 0001 0100 101 14B LSB=1 (1 bit) LSB=1 1
16.0
16.1 16.1.1 16.1.1.1
MT9072 Register Set
T1 Register Set Register Address (000 - FFF) Summaries Framer Address (0XX-9XX) Summary
Hex Address
0XX 1XX 2XX 3XX 4XX 5XX 6XX 7XX 8XX 90X 91X 92X 93X
Binary Address (A11-A0)
000 xxxx xxxx 001 xxxx xxxx 010 xxxx xxxx 011 xxxx xxxx 100 xxxx xxxx 101 xxxx xxxx 110 xxxx xxxx 111 xxxx xxxx 1000 xxxx xxxx 1001 0000 xxxx 1001 0001 xxxx 1001 0010 xxxx 1001 0011 xxxx xxxx indicates all (0000 to 1111) binary possibilities X indicates all (0 to F) hex possibilities
Framer Accessed
0 1 2 3 4 5 6 7 0,1,2...7(reserved for writes only) Global control Registers for the MT9072 Global status Registers for the MT9072 ST-BUS analyser buffer data ST-BUS analyser buffer data
Table 55 - Framer Addressing (0XX - 9XX) (T1)
96
SEMICMF.019
Data Sheet
16.1.1.2 Register Group Address (Y00 - YFF) Summary
Hex Address Y0X YFX Y1X Y2X Y3X Y4X Y5X-Y6X Y7X-Y8X Y9X-YAX YBX-YCX YDX-YEX Register Group Accessed Master Control Master Status Latched Status Interrupt Status Interrupt Mask Per Channel Tx signaling Per Channel Receive signaling Per Channel Control not used not used Processor Access R/W R R R R/W R/W R/W R/W
MT9072
ST-BUS Access ----------yes yes ---
Binary Address (A11-A0) yyyy 0000 xxxx yyyy1111 xxxx yyyy 0001 xxxx yyyy 0010 xxxx yyyy 0011 xxxx yyyy 0100 xxxx yyyy 0101 xxxx yyyy 0110 xxxx yyyy 111 xxxx yyyy 1000 xxxx yyyy 1001 xxxx yyyy 1010 xxxx yyyy 1011 xxxx yyyy 1100 xxxx yyyy 1101 xxxx yyyy 1110 xxxx
xxxx indicates all (0000 to 1111) binary possibilities X indicates all (0 to F) hex possibilities yyyy indicates 9 (000, 001, 010, 011, 111,1000,1001) binary possibilities representing 1 of 8 framers (R/W), and all 8 framers (W only) and global selection. Y indicates 9 (0,1,2,3,4...9) hex possibilities representing 1 of 8 framers (R/W), and all 8 framers (W only), and global selection. Table 56 - Register Group Address (Y00 - YFF) Summary (T1)
SEMICMF.019
97
MT9072
16.1.1.3 Global Control and Status Register (900-91F) Summary
R/W Register Control Bits (B15 - B8 / B7 - B0)
Data Sheet
Binary Address Hex (A11-A0) Address 1001 0000 0000 1001 0000 0001 1001 0000 0010 1001 0000 0011 1001 0000 0100 900 901 902 903 904
R/W Global Control0 R/W Global Control1 R/W R/W Interrupt Vector Mask Register Interrupt Vector Mask Register
T1Eo, STBUS,#,#,#,#,#,#,#,#,#,CK1,#,#,#,RSTC CHANNUM(4:0),STRNUM(4:0),STBUFEN,FRNUM(2:0), CHUP,CONTSIN F3HM,F3EM, F3RM, F3SM,F2HM, F2EM, F2RM, F2SM, F1HM,F1EM, F1RM, F1SM,F0HM, F0EM, F0RM, F0SM F7HM,F7EM, F7RM, F7SM,F6HM, F6EM, F6RM, F6SM, F5HM,F5EM, F5RM, F5SM,F4HM, F4EM, F4RM, F4SM
R/W Framer SLBK8, SLBK67, SLBK45, SLBK23, SLBK01,RLBK8, Loopback Global RLBK67, RLBK45, RLBK23, RLBK01,#, #, #,#,#,# Register R/W not used not used
1001 0000 01101001 0000 1111 1001 0001 0000
906-90F
910
R
Interrupt Vector Status 0 Interrupt Vector Status1 Identification Code Status
F3HVS,F3EVS, F3RVS, F3SVS,F2HVS, F2EVS, F2RVS, F2SVS, F1HVS,F1EVS, F1RVS, F1SVS,F0HVS, F0EVS, F0RVS F0SVS F7HVS,F7EVS, F7RVS, F7SVS,F6HVS, F6EVS, F6RVS, F6SVS, F5HVS,F5EVS, F5RVS, F5SVS,F4HVS, F4EVS, F4RVS F4SVS ID15-0
1001 0001 0001
911
R
1001 0001 0010 1001 0001 0011
912 913
R R
ST-Bus Analyser #,#,#,#,#,#,#,#,#,#,#,#,#,#,#,STIS Interrupt Vector Register not used
1001 0001 01001001 0001 1111 1001 0010 0010 1001 0011 1111 1001 0100 0100 1001 1111 1111
914-91F
920-93F 940-9FF
R
ST-Bus Analyser #,#,#,#,#,#,#,#,STAD(7:0) Data not used
# indicates unused bits in register that may be any value if read Table 57 - Global Control and Status (900 - 91F) Summary (T1)
16.1.1.4
Master Control Registers Address (Y00-Y0F, YF0 to YFF) Summary
98
SEMICMF.019
Data Sheet
Binary Address (A11-A0) yyyy 0000 0000 yyyy 0000 0001 yyyy 0000 0010 yyyy 0000 0011 yyyy 0000 0100 yyyy 0000 0101 yyyy 0000 0110 yyyy 0000 0111 yyyy 0000 1000 yyyy 0000 1001 yyyy 0000 1010 yyyy 0000 1011 yyyy 0000 1100 yyyy 0000 1101 yyyy 0000 1110 yyyy 0000 1111 yyyy 1111 0000 yyyy 1111 0001 yyyy 1111 0010 yyyy 1111 0011 yyyy 1111 0100 Hex Address R/W Y00 Y01 Y02 Y03 Y04 Y05 Y06 Y07 Y08 Y09 Y0A Y0B Y0C Y0D Y0E Y0F YF0 YF1 YF2 YF3 YF4 Register Control Bits (B15 - B8 / B7 - B0)
MT9072
R/W Framing Mode Select Interface R/W Line Coding Word
IMA,#,G.802,JYEL,TRANSP,T1DM,ESF, #, CXC, RS1-0, FSI, REFR, MFREFR, JTS, TXSYNC #,#,#,#,RZCS1,RZCS0,TZCS2,TZCS1,TZCS0,TPDV ,TXB8ZS,RXB8ZS,ADSEQ,RZNRZ, UNIBI, CLKE
R/W Tx Alarm Control Word #,#,#,#,#,#,#,#,TESFYEL,TXSECY,TD4YEL,TAIS, #,TT1DMY,D4SECY,SO R/W Tx Error Control Word #,#,#,#,#,#,#,#,#,L32Z,BPVE,CRCE,FTE,FSE,LOSE, PERR
R/W signaling Control Word #,#,#,#,#,#,CSIGEN,RBEN,#,RSDB,RFL,#, SM1-0,SIP1-0 R/W Loopback Control Word R/W HDLC &Datalink Control Word #,#,#,#,#,#,#,#,#,DLBK,RLBK,STLBK,PLBK,TLU,TL D #,#,#,#,HCH4:0,HPAYSEL,E1.5CK,DLCK,EDLEN, BOMEN, HDLCEN,H1R64 #,#,#,#,#,#,#,#,TXBOM7:0 #,#,#,#,#,#,#,#,RXBOMM7:0 #,#,#,#,#,#,#,#,RXID7:0 #,#,#,#,#,#,#,#,TXID7:0 #,#,#,#,#,#CST(4:0),PCM(4:0)
R/W Tx BOM Register R/W Rx BOM Register Match R/W Receive Idle Code R/W Transmit Idle Code R/W Common Channel signaling Map R/W not used R/W Transmit Loopback Activate Code R/W Transmit Loopback Deactivate Code R/W Receive Loopback Activate Code R/W Receive Loopback Deactivate Code R/W Interrupts and I/O Control R/W HDLC Control0 R/W HDLC Test Control R/W Address Recognition
#,#,#,#,#,#,TXLACL1-0,TXLAC7-0 #,#,#,#,#,#,TXLDL1-0,TXLDC7-0 #,#,#,#,#,#,RXLACL1-0,RXLACM7-0 #,#,#,#,#,#,RXLDCL1-0,RXLDCM7-0 #,#,#,#,#,Tx8KEN,RxDO,TXMFSEL,SPND,INTA, DSToEn,CSToEn,RxCO,CNTCLR,SAMPLE,RST #,#,#,#,#,ADREC,RXEN,TXEN,EOP,FA,MI,CYCLE, TCRCI, SEVEN,RXFRST,TXFRST #,#,#,#,#,#,#,#,#,#.HRST,RTLOOP,CRCTST,FTST, ADTST,HLOOP ADRM26-20,A2EN,ADRM16-10,AEN
Table 58 - Master Control Registers Address (Y00 to Y0F and YF0 to YFF) Summary (T1)
SEMICMF.019
99
MT9072
Binary Address (A11-A0) yyyy 1111 0101 yyyy 1111 0110 yyyy 1111 0111 yyyy 1111 1000 yyyy1111 1111 Hex R/W Address YF5 YF6 YF7 YF8YFF Register Control Bits (B15 - B8 / B7 - B0) #,#,#,#,#,#,#,#,TXFIFO7-0 #,#,#,#,#,#,#,#,CNT7-0 #,#,#,#,#,#,#,#,TXSD7-0 not used
Data Sheet
R/W TX FIFO R/W TX Byte count R/W Transmit Set Delay Bits 7 - 0. not used
xxxx indicates all (0000 to 1111) binary possibilities X indicates all (0 to F) hex possibilities yyyy indicates 9 (000, 001, 010, 011, 111,1000,1001) binary possibilities representing 1 of 8 framers (R/W), all 8 framers (W only), and global selection. Y indicates 9 (0,1,2,3,4...9) hex possibilities representing 1 of 8 framers (R/W), and all 8 framers (W only) and global selection(R/W) Table 58 - Master Control Registers Address (Y00 to Y0F and YF0 to YFF) Summary (T1)
100
SEMICMF.019
Data Sheet
16.1.1.5 Master Status Registers Address (Y10-Y1F) Summary
MT9072
Binary Address Hex (A11-A0) Address R/W yyyy 0001 0000 Y10 R
Register Synchronization and Alarm Status Word Timer Status Word Receive Bit Oriented Message
Control Bits (B15 - B8 / B7 - B0) #, #, TFSYNC,MFSYNC,SE,LOS,D4YALM,D4Y48, SECYEL,ESFYEL,AIS,PDV,LLED,LLDD,T1DRR, T1DRY #,#,#,#,#,#,#,#,#,#,#,#,#,1SEC,2SEC,# #,#,#,#,#,#,RxBOM,RxBOMM,RxBOM7-0
yyyy 0001 0001 yyyy 0001 0010 yyyy 0001 1011 yyyy 0001 0100 yyyy 0001 0101
Y11 Y12 Y13 Y14 Y15
R R R R R
Receive Slip Buffer Word #,#,PIR2:0,RSLPD,RXSLIP,RXFRM, RXTS4-0,RxBC2-0 Transmit Slip Buffer Word #,#,#,#,#,TSLIP,TSLPD,TXSBMSB, TXTS4-0,TXBC2-0
PRBS Error Counter and PSM7-0,PS7-0 CRC Multiframe Counter for PRBS MFOOF MFOOF15-0
yyyy 0001 0110 yyyy 0001 0111 yyyy 0001 1000 yyyy 0001 1001 yyyy 0001 1010 yyyy 0001 1011 yyyy 0001 1100
Y16 Y17 Y18 Y19 Y1A Y1B Y1C
R R R R R R R
Framing Bit ErrorCounter FC15-0 Bipolar Violation Counter BPV15-0 CRC-6 Error Counter CC15-0
OOF and COFA counter OOF7:0,COFA7:0 Excessive Zero Counter TX Byte Counter Position and HDLC Test Status HDLC Status RX CRC RX FIFO #,#,#,#,#,#,#,#,EXZ7:0 #,#,#,#,RXclk,TXclk,Vcrc,Vaddr,TBP7:0
yyyy 0001 1101 yyyy 0001 1110 yyyy 0001 1111
Y1D Y1E Y1F
R R R
#,#,#,#,#,#,#,#,#,IDC,RQ9-8,TXSTAT1-0, RXSTA1-0 CRC15-0 #,#,#,#,#,#,#,#,RXFIFO7-0
xxxx indicates all (0000 to 1111) binary possibilities X indicates all (0 to F) hex possibilities yyyy indicates 9 (000, 001, 010, 011, 111,1000,1001) binary possibilities representing 1 of 8 framers (R/W), and all 8 framers (W only) Y indicates 9 (0,1,2,3,4...9) hex possibilities representing 1 of 8 framers (R/W), and all 8 framers (W only) Table 59 - Master Status Register(R) Address(Y1X) Summary (T1)
SEMICMF.019
101
MT9072
16.1.1.6 Latched Status Registers Address (Y20-Y2F) Summary
Latched Status Register not used HDLC Status Latch Receive Sync and Alarm Latch Receive Line status and Time Latch Elastic Store and Excessive zero Latch not used Framing Bit Counter Latch Error FCL<15:0> not used
Data Sheet
Binary Address Hex (A11-A0) Address R/W yyyy 0010 0000- Y20-Y22 yyyy 0010 0010 yyyy 0010 0011 yyyy 0010 0100 Y23 Y24 R R
Status Bits (B15 - B8 / B7 - B0)
#,#,#,#,#,#,#,GAL,EOPDL,TEOPL,EOPRL,TXFLL, FAL,TXUNDERL,RXFFL,RXOVFLL FEOL,CRCOL,OOFOL,COFAOL,BPVOL,PRBSOL ,PRBSMFOL,MFOOFOL,TFSYNL,MFSYNL,FBEL, COFAL,SEFL,AISL, CRCL,LOSL D4YALML,D4Y48L,SECYELL,ESFYELL,T1DMYL, #,BPVL,PRBSL,PDVL,LLEDL,LLDDL,RXBOML, RXBOMML,CASRL,1SECL,2SECL #,#,#,#,#,#,#,#,#,#,#,#,EXZOL,EXZL,TXSLIPL, RXSLIPL
yyyy 0010 0101
Y25
R
yyyy 0010 0110 yyyy 0010 0111 yyyy 0010 1000 yyyy 0010 1001 yyyy 0010 1010 yyyy 0010 1011
Y26 Y27 Y28 Y29 Y2A Y2B
R R R R R R
Bipolar Violation Error BPVL<15:0> Counter Latch CRC-6 Error Counter CRCL<15:0> Latch Out of Frame and OOFL<7:0>,COFAL<7:0> Change of Frame Count Latch Multiframe Out of Frame Count Latch MFOOFL<15:0>
yyyy 0010 1100
Y2C
R
yyyy 0010 1101 yyyy 0010 1111
Y2DY2F
not used
xxxx indicates all (0000 to 1111) binary possibilities X indicates all (0 to F) hex possibilities yyyy indicates 9 (000, 001, 010, 011, 111,1000,1001) binary possibilities representing 1 of 8 framers (R/W), all 8 framers (W only) and global selection. Y indicates 9 (0,1,2,3,4...9) hex possibilities representing 1 of 8 framers (R/W), and all 8 framers (W only) and global selection. Table 60 - Latched Status Register (R) Address (Y2X) Summary (T1)
102
SEMICMF.019
Data Sheet
16.1.1.7 Interrupt Status Registers Address (Y30-Y3F) Summary
Interrupt Status Register not used HDLC Interrupt Status Receive Sync and Alarm Interrupt Status Receive Line and Timer Interrupt Status Elastic Store and Excessive Zero Interrupt Status not used not used Status Bits (B15 - B8 / B7 - B0)
MT9072
Binary Address Hex R/W (A11-A0) Address yyyy 0011 0000 yyyy 0011 0010 yyyy 0011 0011 yyyy 0011 0100 Y30-Y32 Y33 Y34 R R
#,#,#,#,#,#,#,GAI,EOPDI,TEOPI,EOPRI,TXFLI,FA, TXUNDERI,RXFFI,RXOVFLI FEOI,CRCOI,OOFOI,COFAOI,BPVOI,PRBSOI,PR BSMFOI,MFOOFOI,TFSYNI,MFSYNI,FBEI,COFA, SEFI,AISI,CRCI,LOSI D4YALMI,D4Y48I,SECYELI,ESFYELI,T1DMYI,#, BPVI,PRBSI,PDVI,LLEDI,LLDDI,BIOMI,BOMMI, CASRI,1SECI,2SECI #,#,#,#,#,#,#,#,#,#,#,#,EXZOI,EXZI,TXSLIPI, RXSLIPI not used
yyyy 0011 0101
Y35
R
yyyy 0011 0110
Y36
R
yyyy 0011 0111- Y37-Y3F yyyy 0011 1111
xxxx indicates all (0000 to 1111) binary possibilities X indicates all (0 to F) hex possibilities yyyy indicates 9 (000, 001, 010, 011, 111,1000,1001) binary possibilities representing 1 of 8 framers (R/W), all 8 framers (W only) and global selection. Y indicates 9 (0,1,2,3,4...9) hex possibilities representing 1 of 8 framers (R/W), and all 8 framers (W only) and global selection. Table 61 - Interrupt Status Register (R) Address (Y3X) Summary (T1)
SEMICMF.019
103
MT9072
16.1.2 Interrupt Mask Registers Address (Y40-Y4F) Summary
Hex Address R/W Y40-Y42 Y43 Y44 R R Interrupt Mask Register not used not used
Data Sheet
Binary Address (A11-A0) yyyy 0010 0000yyyy 0010 0010 yyyy 0100 0011 yyyy 0100 0100
Control Bits (B15 - B8 / B7 - B0)
HDLC Interrupt Mask #,#,#,#,#,#,#,GAIM,EOPDIM,TEOPIM,EOPRIM, TXFLIM,FAIM,TXUNDERIM,RXFFIM,RXOVFLIM Receive Sync and Alarm Interrupt Mask FEOIM,CRCOIM,OOFOIM,COFAOIM,BPVOIM, PRBSOIM,PRBSMFOIM,MFOOFOIM,TFSYNIM, MFSYNIM,FBEIM,COFAIM,SEFIM,AISIM,CRCIM, LOSIM D4YALMIM,D4Y48IM,SECYELIM,ESFYELIM, T1DMYIM,#,BPVIM,PRBSIM,PDVIM,LLEDIM, LLDDIM,BIOMIM,BOMMIM,CASRIM,1SECIM,2SE CIM #,#,#,#,#,#,#,#,#,#,#,EXZOIM,EXZIM,TXSLIPIM, RXSLIPIM not used
yyyy 0100 0101
Y45
R
Receive Line status and Timer Interrupt Mask Elastic Store and Excessive Zero Interrupt Mask not used
yyyy 0100 0110
Y46
R
yyyy 0100 0111 yyyy 0100 1111
Y47-Y4F
R
xxxx indicates all (0000 to 1111) binary possibilities X indicates all (0 to F) hex possibilities yyyy indicates 9 (000, 001, 010, 011, 111,1000,1001) binary possibilities representing 1 of 8 framers (R/W), and all 8 framers (W only) and global selection. Y indicates 9 (0,1,2,3,4...9) hex possibilities representing 1 of 8 framers (R/W), and all 8 framers (W only) and global selection. Table 62 - Interrupt Mask Register (R/W) Address (Y4X) Summary (T1)
16.1.3
Master Control Registers (Y00 to YF0 ) Bit Functions
Tables 64 to 79 describe the bit functions of each of the Master Control Registers in the MT9072. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2,... Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11 A10 A9 A8). In addition, a simultaneous write to all 8 Framers is possible by setting the address A11 to 1 and A10 to A8 to 0. A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a hard reset (the RESET pin is toggled from zero to one), or a software reset (the RST bit in control register address YF1 is toggled from one to zero or toggling of RSTC in Global Control Register). The (#) indicates that a (0) or (1) is possible.
104
SEMICMF.019
Data Sheet
Bit 15 Name IMA (0) Functional Description
MT9072
Inverse Mux for ATM Mode. Setting this bit high allows the IO port to be easily connected to one of the Zarlink IMA devices such as MT90220. DSTi becomes a serial 1.544 Mb/s data stream. C4b becomes a 1.544 MHz clock that clocks DSTi in on the falling edge. RXFPB becomes a positive framing pulse that is high for the first bit of the serial T1 stream coming from the DSTo pin. The data from DSTo is clocked out on the rising edge of RXDLC. Set this pin low for all other applications. Note that signaling operations CSTi/CSTo do not function in the IMA Mode. The Global Control Register 900 bit CK1 is ignored for this mode. 8.192 Mbit/s backplane mode is not supported if IMA mode is selected on any of the framer's. not used. G802 Mode. If set, this bit maps DSTi data channels transparently onto the transmit line data and maps the receive data onto DSTo channels as per G.802. Japan Yellow Alarm Set this bit high to select a pattern of 16 ones (111111111111111) as the ESF yellow alarm. In order to transmit the japan yellow alarm the TESFYEL bit has to be set.
14 13 12 11
# G.802 (0) JYEL (0)
TRANSP Transparent Mode Select. In transparent Mode the data present at the DSTi channels are (0) transparently sent to the T1 interface. The S bit from the DSTi interface (Channel 31 if running at 2.048 Mb/s backplane) is sent to the S bit position of the T1 interface.The rest of the channelized data is sent unaltered to the T1 interface. Ensure that TCPI of per channel controlis not set. T1DM (0) T1DM Mode Select. Set this bit high to select T1DM Mode. In T1DM the Ft and Fs pattern is the same as the D4 Mode but a 1011YR0 pattern is sent and detected in Channel 24 of the T1 interface. Bit Y is used to indicate a yellow Alarm and R bit is used by AT&T for a 8 Kb/s communication channel. Extended Super Frame. Setting this bit enables transmission and reception of the 24 frame superframe DS1 protocol. not used. Cross Check. Setting this bit in ESF mode enables a cross check of the CRC-6 remainder before the frame synchronizer pulls into sync. This process adds at least 6 milliseconds to the frame synchronization time. Reframe Select 1 - 0. These bits set the criteria for an automatic reframe in the event of framing bits errors. The combinations available are: RS1 - 0, RS0 - 0 = sliding window of 2 errors out of 4 frames. RS1 - 0, RS0 - 1 = sliding window of 2 errors out of 5 frames. RS1 - 1, RS0 - 0 = sliding window of 2 errors out of 6 frames. RS1 - 1, RS0 - 1 = no reframes due to framing bit errors. Note that for T1DM mode, the definition of frame boundary is starting from the channel 1 data including the synchronization byte(10111YR0) and the following' S' bit. The Y and the R bits are ignored for synchronization. Fs Bit Include. Only applicable in D4 mode. Setting this bit causes errored Fs bits to be included as framing bit errors. A bad Fs bit will increment the Framing Error Bit Counter, and will potentially cause a reframe. The Fs bit of the receive frame 12 will only be included if D4SECY is set. Note that when FSI bit is set both Ft and Fs are taken into consideration before declaration of synchronization Reframe. A 0 to 1 transition of this bit causes an automatic reframe. Table 63 - Framing Mode Select (R/W Address Y00) (T1)
10
9 8 7
ESF (0) (0) CXC (0) RS1-0 (00)
6-5
4
FSI (0)
3
REFR (0)
SEMICMF.019
105
MT9072
Bit 2 Name Functional Description
Data Sheet
MFREFR MultiFrame Reframe. Only applicable in D4 mode. Setting this bit causes an automatic (0) multiframe reframe. The signaling bits are frozen until multiframe synchronization is achieved. Terminal frame synchronization is not affected. JTS (0) Japan Telecom Synchronization. If this bit is set, the S-bit is included in the CRC6 calculation for the ESF framing Mode.
1 0
TxSYNC Transmit Synchronization. Setting this bit causes the transmit multiframe boundary to be (0) internally synchronized to the incoming S-bits on DSTi channel 31 bit 0. Table 63 - Framing Mode Select (R/W Address Y00) (T1)
106
SEMICMF.019
Data Sheet
Bit 15-12 11-10 Name # not used. Functional Description
MT9072
RZCS1-0 Receive Zero Code Suppression. (00) 00: No Zero Code Suppression. 01: GTE Zero Code Suppression 00000001 of an byte is detected and replaced by a 00000000 10: DDS Zero Code Suppression.10011000 is detected as a zero byte and replaced by 00000000. 11: Bell Zero Code Suppression (Bit 7,00000010) is detected as a zero byte and replaced by a zero byte. These suppression detection codes only apply to the receiver. Note that the bit designations are with respect to the PCM24 side where bit 1 is sent and received first. TZCS2-0 Transmit Zero Code Suppression. (000) 000: No Zero Code Suppression. 001: GTE Zero Code Suppression. Bit 8 of an all zero channel byte is replaced by a one, except in signaling frames where bit 7 is forced to a one. 010: DDS Zero Code Suppression. An all zero byte is replaced by 10011000. 011: Bell Zero Code Suppression. Bit 7 of an all zero channel is replaced by a 00000010, 100: "Jammed bit 8". Bit 8 of all channels are replaced by a 1. These suppression codes only apply to the transmitter. Note that if a suppression code is enabled for a channel the B8ZS coding will not take place for the channel. Although 8 consecutive zeros in a non channel boundary will be subjected to B8ZS suppression. Note that the bit designations are with respect to the PCM24 side where bit 1 is sent and received first. TPDV (0) TXB8ZS (0) RXB8ZS (0) ADSEQ (0) RZNRZ (0) UNIBI (0) Transmit PDV. The output of the T1 data to be sent is monitored over a T1 frame and if the density is less than 12.5% a bit is added, in the non-framing bit. Transmit Bipolar Eight Zero Substitution. If set all zero octets in the transmit path are substituted with B8ZS codes. Receive Bipolar Eight Zero Substitution. If set B8ZS code words in the receive path are substituted with all zero octets. Bipolar violations assosciated with incoming B8ZS words will not be counted by the Bipolar Violation Error Counter. Digital Milliwatt or Digital Test Sequence. If one, the Mulaw digital milliwatt analog test sequence will be selected for those channels with per timeslot control bits TTST, RRST set. If zero, a PRBS generator / detector will be connected to channels with TTST, RRST set. Return to zero Non Return to zero. If one return to zero inputs and outputs are expected at the T1 interface. If zero, Non return to zero input and output are expected. RZ mode is only supported for bipolar input. Unipolar/Bipolar. If one the input and output at the T1 interface is assumed to be unipolar. The stream RPOS is the input and TPOS is the output. Setting this bit low causes the MT9072 to accept complementary bipolar inputs on RPOS/RNEG and to transmit complementary outputs on TPOS/TNEG. Clock Edge. If one then the NRZ data(RPOS/RNEG) is sampled on the rising edge and transmitted on the falling edge of TXCL. If this bit is 0, then the opposite edges are used.This selection is only applicable in NRZ mode. Table 64 - Line Interface and Coding Word(Y01) (T1)
9-7
6 5 4
3
2
1
0
CLKE (0)
SEMICMF.019
107
MT9072
Bit 15-8 7 Name # not used. Functional Description
Data Sheet
TESFYEL Transmit ESF Yellow Alarm. Setting this bit(while in ESF Mode) causes a repeating pattern (0) of eight 1's followed by eight 0's to be sent on the transmit FDL bits. When JYEL is set, all ones signal is sent on the FDL. TXSECY Transmit Secondary Yellow Alarm. When set to 1, the S-bit for transmit frame 12 will to be (0) set to 1. TD4YEL Transmit D4 Yellow Alarm. When set, bit 2 of all DS0 channels are forced low. The definition (0) of Bit 2 is in accordance with Figure 55. TAIS (1) # Transmit All Ones. When low, this control bit forces a framed or unframed (depending on the state of Transmit Alarm Control bit 0) all ones to be transmit at TTIP and TRING. not used.
6 5 4 3 2 1
TT1DMY Transmit T1DM Yellow Alarm. If this bit is 0 a T1DM yellow alarm is sent on bit 2 of the 24th (1) timeslot. D4SECY D4 Secondary Alarm. Set this bit for trunks employing the secondary Yellow Alarm. The Fs bit (0) in the 12th frame will not be used for counting errored framing bits. If a one is received in the Fs bit position of the 12th frame a Secondary Yellow Alarm Detect bit will be set. SO (0) S-bit Override. If set, this bit forces the S-bits to be inserted as an overlay on any of the following alarm conditions: i) transmit all ones, ii) loop up code insertion, iii) loop down code insertion. Table 65 - Transmit Alarm Control Word(Y02) (T1)
0
Bit 15-7 6 5 4 3 2 1 0
Name # L32Z (0) BPVE (0) CRCE (0) FTE (0) FSE (0) LOSE (0) PERR (0) not used.
Functional Description
Digital Loss of Signal Selection. If one, the threshold for digital loss of signal is 32 successive zeros. If zero, the threshold is set to 192 successive zeros. Bipolar Violation Error Insertion. A zero-to-one transition of this bit inserts a single bipolar violation error into the transmit DS1 data. CRC-6 Error Insertion. A zero-to-one transition of this bit inserts a single CRC-6 error into the transmit ESF DS1 data. Terminal Framing Bit Error Insertion. A zero-to-one transition of this bit inserts a single error into the transmit D4 Ft pattern or the transmit ESF framing bit pattern (in ESF mode). Signal Framing Bit Error Insertion. A zero-to-one transition of this bit inserts a single error into the transmit Fs bits (in D4 mode only). Loss of Signal Error Insertion. If one, the MT9072 transmits an all zeros signal (no pulses). Zero code suppression is overridden. If zero, data is transmitted normally. Payload Error Insertion. A zero - to - one transition of this bit inserts a single bit error in the transmit payload. Table 66 - Transmit Error Control Word(Y03) (T1)
108
SEMICMF.019
Data Sheet
Bit 15-10 9 Name # not used. Functional Description
MT9072
CSIGEN Common Channel Signaling Enable. Setting this bit enables common channel signaling in (0) conjunction with register Y0B. All other channels on the CSTo stream are tristate. Register Y0B defines the map between CST and PCM stream. RBEN (0) not used RSDB (0) RFL (0) # SM1-0 (00) Receive Signaling Debounce. Setting this bit causes incoming signaling bits to be debounced for a period of 6 to 9 milliseconds before reporting on CSTo streams or in the Receive signaling Bits Registers.. Receive Signaling Freeze Due to Loss. If one, the receive signaling is frozen if a receive loss of signal is detected. The freeze is cleared upon clearance of Loss. not used. Signaling Message. These two bits are used to fill the vacant bit positions available on CSTo when the MT9072 is operating on a D4 trunk. The first two bits of each reporting nibble of CSTo contain the AB signaling bits. The last two will contain SM1 and SM0 (in that order). When the MT9072 is connected to ESF trunks four signaling bits (ABCD) are reported and the bits SM1-0 settings are ignored. Signaling Interrupt Period. These 2 bits determine the signaling Interrupt period due to the Receive signaling changes. This 2 bits determine the duration of the signaling interrupt bit CASRI(Y35). 00 2 Msec Period 01 8 Msec Period 10 16 Msec Period Table 67 - Signaling Control Word (Y04) (T1) Robbed Bit Signaling Enable. Setting this bit multiplexes the AB or ABCD signaling bits into bit position 8 of all DS0 channels every 6th frame. Signaling is only sent in channels for which the CC bit in the per channel control word (Address Y90 - YA7) is set to 1.
8
7 6
5 4 3-2
1-0
SIP1-0
SEMICMF.019
109
MT9072
Bit 15-6 5 Name # DLBK (0) RLBK (0) not used. Functional Description
Data Sheet
Digital Loopback. If one, then the digital streams (TPOS/TNEG) are looped to RPOS/RNEG. Data coming out of DSTo will be a delayed version of DSTi. Hence the data path is DSTi through the Transmitter to RPOS/RNEG and through the receiver to DSTo. Remote Loopback. If one, then all timeslots received on RPOS/RNEG are connected to TPOS/TNEG on the DS1 side of the MT9072. If zero, then this feature is disabled.
4 3
STLBK ST-BUS Loopback. If one, then the last bit in the frame and the first 24 timeslots of DSTi are (0) connected to the last bit in the frame and the first 24 timeslots of DSTo on the ST-BUS side of the MT9072. If zero, then this feature is disabled. See Loopbacks section. PLBK (0) Payload Loopback. If one, then all timeslots received on RPOS/RNEG are connected to TPOS/TNEG on the ST-BUS side of the MT9072. Hence DSTo is looped back to DSTi. If zero, then this feature is disabled. Set the bit RxDO (YF1 bit 9) for the payload loopback data to appear at the transmitter output. TxLoopUp Code. If this bit is set inband line loopup code is sent. The loopup code to be sent is determined by the Tx Loopup Code register. Note that the receiver will detect either framed or unframed inband loop codes. TxLoopDown Code. If this bit is set inband line loopdown code is sent. The loopdown code to be sent is determined by the Tx LoopDown Code register. If both TLU and TLD are set TLD takes precedence. Table 68 - LoopBack Control Word (Y05) (T1)
2
1
TLU (0) TLD (0)
0
110
SEMICMF.019
Data Sheet
Bit 15-12 11-7 Name # HCH4-0 (0) not used. Functional Description
MT9072
HDLC Channel 4-0. This 5 bit number specifies the timeslot the HDLC will be attached to if enabled. Timeslot 0 is the first channel in the frame. Timeslot 23 is the last channel available in a T1 frame. If enabled in a channel, HDLC data will be substituted for data from DSTi on the transmit side. Receive data is extracted from the incoming line data before the elastic buffer.
6 5
HPAYSEL HDLC Payload Select. Set this bit to 1 to attach HDLC to a payload timeslot, if zero it is (0) attached to the Facility Data Link when in the ESF mode. E1.5CK (0) Extracted 1.5 Data Link Clock. If one, the RxDLC pin outputs a 1.544 MHz clock signal derived from the 1.544MHz clock signal at the EXCLi pin. This clock is synchronous with the receive data before it passes through the elastic buffer at the RxDL pin. If zero, the RxDLC pin operates as a receive data link clock or enable signal as programmed by control bit DLCK (register address Y06). Data Link Clock. If one, the TxDLC and RxDLC pins output a gapped clock. If zero, the TxDLC and RxDLC pins output an active low enable signal. Enable Data Link. Setting this bit multiplexes the serial stream clocked in on pin TxDL into the FDL bit position (ESF mode) or the Fs bit position (D4 mode). Bit Oriented Message Enable. Setting this bit enables transmission of bit - oriented messages on the ESF facility data link. The actual message transmitted at any one time is contained in the Tx BOM register (Y07).
4 3 2
DLCK (0) EDLEN (0) BOMEN (0)
1
HDLCEN HDLC Enable. If this bit is set and HPAYSEL is a zero than the internal HDLC is connected (0) to the FDL bits in ESF Mode and TXDL/RXDL are not used for the dataLink. If 0 the datalink is sourced/sinked from TXDL/RXDL. H1R64 (0) HDLC Rate Select. Setting this bit high while the HDLC is activated on a timeslot enables 64 Kb/s operation. Setting this bit low while an HDLC is activated enables 56 Kb/s operation (this prevents data corruption due to forced bit stuffing). Table 69 - HDLC & DataLink Control Word(Y06) (T1)
0
Bit 15-8 7-0
Name # not used.
Functional Description
TXBOM Transmit Bit Oriented Message. The contents of this register are concatenated with a sequence of eight 1's and continuously transmit in the FDL bit position of ESF trunks. Normally 7-0 (0) the leading bit (bit 7) and last bit (bit 0) of this register are set to zero. Note that in accordance to T1.403 Table 11 the codeword 7E should not be used due to similarity of DataLink idle code. Table 70 - Transmit Bit Oriented Message Register (Y07) (T1)
SEMICMF.019
111
MT9072
Bit 15-8 7-0 Name # not used. Functional Description
Data Sheet
RXBOM Receive Bit Oriented Message Match. The contents of this register are compared to the M7-0 received bit oriented message register(RXBOM) and an option maskable interrupt is generated if (0) the contents match the received bit oriented message. Note that in accordance to T1.403 Table 11 the codeword 7E should not be used due to similarity of DataLink idle code. The code 7E will not be detected by the MT9072. Table 71 - Receive Bit Oriented Message Match Register(Y08) (T1)
Bit 15-8 7-0
Name # not used.
Functional Description
RXIDC Receive Idle Code. This is the idle code that is sent on the DSTo channels if the per timeslot 7-0 control bit MPDR is set(Y90-YA7). (0) Table 72 - Receive Idle Code Register(Y09) (T1)
Bit 15-8 7-0
Name # not used.
Functional Description
TXIDC Transmit Idle Code. This is the idle code that is sent on the PCM24 channels if the per timeslot 7-0 control bit MPDT is set(Y90-YA7). (0) Table 73 - Transmit Idle Code Register(Y0A) (T1)
Bit 15-10 9-5
Name # CST(4:0) (00000) not used.
Functional Description
CST Map Channel. This is the CSTi/o channel which will be used as a source/destination to be mapped to the PCM24 channel. The possible values are 0 to 23 for channels 0 to 23 of the CSTi/o streams.
4-0
PCM(4:0) PCM Map Channel. This is the PCM24 timeslot which will be used as a source/destination to (00000) be mapped to the CSTi/o channel. The possible values are 0 to 23 for timeslots 0 to 23 of the PCM24 stream. Table 74 - Common Channel Signaling Map Register(Y0B) (T1)
112
SEMICMF.019
Data Sheet
Bit 15-10 9-8 Name # TXLACL 1-0 (00) not used Functional Description
MT9072
Transmit Loop Activate Code Length. These 2 bits define the length of the transmit loop up code. 00-Code length is 5 bits 01-Code length is 6 or 3 bits 10-Code length is 7 bits 11-Code length is 8 or 4 bits Note: if 3 bit code or 4 bit code is required the bits have to be repeated in TXLDC7-0. For instance if the code 1011 is desired, the TXLAC has to be set to 10111011 and the length TXLACL to 11.
7-0
TXLAC7-0 Transmit Loop Activate Code. This byte specifies the inband loopup code to be (0000 transmitted. The default values are the T1.403 values for Loop Activate Code. 0001) Table 75 - Transmit Loop Activate Code Register(Y0D) (T1)
Bit 15-10 9-8
Name # TXLDCL 1-0 (01) not used
Functional Description
Transmit Loop Deactivate Code Length. These 2 bits define the length of the transmit loop down code. 00-Code length is 5 bits 01-Code length is 6 or 3 bits 10-Code length is 7 bits 11-Code length is 8 or 4 bits Note if 3 bit code or 4 bit code is required the bits have to be repeated in the TXLDC7-0. For instance if the code 1011 is desired, the TXLDC has to be set to 10111011 and TxDLCL to 11
7-0
TXLDC7-0 Transmit Loop Deactivate Code. This byte specifies the inband loopdown code to be (0000 transmitted. If 001 is to be transmitted as a loopdown code; the register has to programmed 1001) to a value of XX001001and the length (TXLDL has to be 01).The default values are the T1.403 values for Loop Deactivate Code. Table 76 - Transmit Loop Deactivate Code Register(Y0E) (T1)
SEMICMF.019
113
MT9072
Bit 15-10 9-8 Name # not used Functional Description
Data Sheet
RXLACL Receive Loop Activate Code Length. These 2 bits define the length of the receive loop up 1-0 code. (00) 00-Code length is 5 bits 01-Code length is 6 or 3 bits 10-Code length is 7 bits 11-Code length is 8 or 4 bits Note: if 3 bit code or 4 bit code is required the bits have to be repeated in RXLACM7-0. For instance if the code 1011 is desired the RXLACM has to be set to 10111011 and the RXLACL to 11. In case of the 3 bit code the 2 most significant bits of RXLACM are ignored. RXLACM 7-0 (0000 0001) Receive Loop Activate Code Match.This byte specifies the match code for the receive loopback activate code. A maskable interrupt can be generated if the loopback activate code message is received. This byte is compared to RXLAC. The default values are the T1.403 values for Loop Activate Code. Table 77 - Receive Loop Activate Code Match Register(Y0F) (T1)
7-0
Bit 15-10 9-8
Name # not used
Functional Description
RXLDCL Receive Loop Deactivate Code Length. These 2 bits define the length of the receive loop up 1-0 code. (00) 00-Code length is 5 bits 01-Code length is 6 or 3 bits 10-Code length is 7 bits 11-Code length is 8 or 4 bits Note: if 3 bit code or 4 bit code is required the bits have to be repeated in RXLACM7-0. For instance if the code 1011 is desired the RXLACM has to be set to 10111011 and the RXLACL to 11. In case of the 3 bit code the 2 most significant bits of RXLACM are ignored. RXLDCM 7-0 (0000 0001) Receive Loop Deactivate Code Match.This byte specifies the match code for the receive loopback activate code. A maskable interrupt can be generated if the loopback activate code message is received. This byte is compared to RXLAC. The default values are the T1.403 values for Loop Activate Code.
7-0
Table 78 - Receive Loop Deactivate code Match Register (R/W Address YF0)
114
SEMICMF.019
Data Sheet
16.1.4 Master Status Registers(Y10-Y18)Bit Functions
MT9072
Tables 80 to 95 describe the bit functions of each of the Master Status Registers in the MT9072. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2... and Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11A10 A9 A8). All status bits will power up in the inactive state until the event happens.
Bit 15-14 13
Name # not used
Functional Description
TFSYNC Terminal Frame Synchronization. Indicates the Terminal Frame Synchronization status (1 - loss; 0 - acquired). For ESF links terminal frame synchronization and multiframe synchronization are synonymous. This bit is also used for indicating T1DM sync gain or loss. MFSYNC Multiframe Synchronization. Indicates the Multiframe Synchronization status (1 - loss; 0 acquired). For ESF Mode multiframe synchronization and terminal frame synchronization are synonymous. MFSYNC is relevant in all T1 Modes. SE Severely Errored Frame. This bit toggles when 2 of the last 6 received framing bits are in error. The framing bits monitored are the ESF framing bits for ESF links, a combination of Ft and Fs bits for D4 links (See Framing Mode Selection Word Y00) and T1DM Mode. Digital Loss of Signal. This bit goes high after the detection of 192 or 32 consecutive zeros dependent on the setting of L32Z bit. It returns low when the incoming pulse density exceeds 12.5%. D4 Yellow Alarm. This bit is set if bit position 2 of virtually every DS0 channel is a zero for a period of 600 milliseconds. The alarm is tolerant of errors by permitting up to 16 ones in a 48 millisecond integration period. The alarm clears in 200 milliseconds after being removed from the line. The alarm will also clear if four 48 msec intervals are detected with more than 16 ones in bit position 2. D4 Yellow Alarm - 48 Millisecond Sample. This bit is set if bit position 2 of virtually every DS0 channel is a zero for a period of 48 milliseconds. The alarm is tolerant of errors by permitting up to 16 ones in the integration period. This bit is updated every 48 milliseconds. Secondary D4 Yellow Alarm. This bit is set if 2 consecutive'1's are received in the S-bit position of the 12th frame of the D4 superframe. ESF Yellow Alarm. This bit is set if the ESF yellow alarm 0000000011111111 is received in eight or more codewords out of ten in the Bit oriented message location which are the FDL bits. AIS Alarm. This bit is set if less than 5 zeros are received in a 3 millisecond window. The AIS bit is set to ahigh after power up. Pulse Density Violation. This bit toggles if the receive data fails to meet ones density requirements. It will toggle upon detection of 16 consecutive zeros on the line data, or if there are fewer than N ones in a window of 8(N+1) bits - where N = 1 to 23. Line Loopback Enable Detect. This bit will be set when a framed or unframed repeating pattern of 00001 has been detected during a 48 millisecond interval. Up to fifteen errors are permitted per integration period. Note that the code detected is dependent on Receive Loopback Activate Code Match(Y0F). Table 79 - Synchronization and Alarm Status Word(Y10) (T1)
12
11
10
LOS
9
D4YALM
8
D4Y48
7 6
SECYEL ESFYEL
5 4
AIS PDV
3
LLED
SEMICMF.019
115
MT9072
Bit 2 Name LLDD (0) Functional Description
Data Sheet
Line Loopback Disable Detect. This bit will be set when a framed or unframed repeating pattern of 001 has been detected during a 48 millisecond interval. Up to fifteen errors are permitted per integration period.Note that the code detected is dependent on Receive Loopback Deactivate Code Match (YF0). T1DM Received R bit. This bit is used for AT&T 8 KB/s communications channel. This bit will be received in bit 1 of timeslot 24 of the receive PCM24 stream in T1DM mode. T1DM Received Yellow Alarm. If this bit is 0 a T1DM yellow alarm has been detected in bit 2 of timeslot 24 of the receive PCM24 stream in T1DM mode. Table 79 - Synchronization and Alarm Status Word(Y10) (T1)
1 0
T1DRR (0) T1DRY
Bit 15-3 2 1 0
Name # 1SEC 2SEC # not used.
Functional Description
One Second Timer Status. This bit changes state once every 1 second. Two Second Timer Status. This bit changes state once every 2 seconds and is synchronous with the 1 SEC timer. not used. Table 80 - Timer Status Word(Y11) (T1)
Bit 15-10 9 8 7-0
Name # RxBOM RxBOMM RxBOM7 - 0 not used.
Functional Description
Bit Oriented Message Received. This bit is set when a Received Bit Oriented Message is received. Receive Bit Oriented Match. This bit is set if there is a match between the Received Bit Oriented Message and Receive Bit oriented Match register. Receive Bit Oriented Message. This is the bit oriented message received. This register is updated after 8 out of 10 messages are received. Table 81 - Receive Bit Oriented Message(Y12) (T1)
116
SEMICMF.019
Data Sheet
Bit 15-14 13-11 Name # PI2-0 not used. Functional Description
MT9072
Phase Indicator Bits (PI2 to PI0). These bits make up 3 least significant bits of a 12 bit word which indicate the delay through the receive slip buffer. The delay through the slip buffer in 2.048 Mhz bit cells is ( 512 - Phase Indicator bits). The delay to DSTo from the write into the slip buffer is ( 512 - Phase Indicator bits) + 16 bits. These bits are updated when the slip buffer write address is 0. These 3 bits will reflect the 1/2,1/4 and 1/8 fractions of the Phase Indicator Bits. Receive Slip Direction. If one, indicates that the last received frame slip resulted in a repeated frame, i.e., the system clock (C4b) is faster than network clock (EXCLi). If zero, indicates that the last received frame slip resulted in a lost frame, i.e., system clock slower than network clock. Updated on an RSLIP occurrence basis. Receive Slip. A change of state (i.e. 1-to-0 one 0-to-1) indicates that a receive controlled frame slip has occured. Receive Frame. The most significant bit of the phase status word. If one, the delay through the receive elastic buffer is greater than one frame in length; if zero, the delay through the receive elastic buffer is less than one frame in length.
10
RSLPD
9 8
RxSLIP RxFRM
7-3
RxTS4 - 0 Receive Timeslot. A five bit counter that indicates the number of timeslots between the receive elastic buffer internal write frame boundary and the ST-BUS read frame boundary. The count is updated every 250 uS. RxBC2 - 0 Receive Bit Count. A three bit counter that indicates the number of ST-BUS bit times there are between the receive elastic buffer internal write frame boundary and the ST-BUS read frame boundary. The count is updated every 250 uS. Table 82 - Receive Slip Buffer Status Word(Y13) (T1)
2-0
SEMICMF.019
117
MT9072
Bit 15-11 10 9 Name # TSLIP TSLPD not used. Functional Description
Data Sheet
Transmit Slip. A change of state (i.e., 1-to-0 or 0-to-1) indicates that a transmit controlled frame slip has occurred in the transmitter. Transmit Slip Direction. If one, indicates that the last transmit frame slip resulted in a repeated frame, i.e., the internally generated 1.544 MHz. transmit clock is faster than the system clock (C4b). If zero, indicates that the last transmit frame slip resulted in a lost frame, i.e., the internally generated 1.544 MHz. transmit clock is slower than network clock. Updated on an TSLIP occurrence. Transmit Slip Buffer MSB. The most significant bit of the Transmit Slip Buffer Delay Word. If one, the delay through the transmit elastic buffer is greater than one frame in length; if zero, the delay through the transmit elastic buffer is less than one frame in length. This bit is reset whenever Transmit Set Delay Bits (register address YF7) - are written to. Transmit timeslot. A five bit counter that indicates the number of ST-BUS timeslots between the transmit elastic buffer ST-BUS write frame boundary and the internal transmit read frame boundary. The count is updated every 250 uS. Transmit Bit Count. A three bit counter that indicates the number of ST-BUS bit times there are between the transmit elastic buffer ST-BUS write frame boundary and the internal read frame boundary. The count is updated every 250 uS. Table 83 - Transmit Slip Buffer Status Word(Y14) (T1)
8
TxSBMSB
7-3
TxTS4 - 0
2-0
TxBC2 - 0
Bit 15-8 7-0
Name PSM7-0 PS7-0
Functional Description PRBS Multiframe Counter.This counter is incremented for each received CRC multiframe. It is cleared when the PRBS Error Counter is written to. PRBS Error Counter.This counter is incremented for each PRBS error detected on any of the receive channels connected to the PRBS error detector.
Table 84 - PRBS Error Counter and CRC Multiframe Counter for PRBS(Y15) (T1)
Bit 15-0
Name
Functional Description
MFOOF15-0 Multiframes Out of Synchronization Counter. This 16 bit counter will be incremented (1) once for every multiframe (1.5 milliseconds in D4 mode, 3 milliseconds in ESF mode) in which basic frame synchronization is lost. This counter presets to one upon reset. If terminal frame synchronization is neverobtained, the MFOOF counter will keep incrementing every 1.5 or 3 msec (ESF Mode) Table 85 - Multiframe Out of Frame Counter(Y16) (T1)
118
SEMICMF.019
Data Sheet
MT9072
Functional Description Framing Bit Error Counter. This 16 bit counter will be incremented for each error in the received framing pattern. In ESF mode the ESF framing bits are monitored. In D4 mode the counter reflects the combination of Ft and Fs errors. The count is only active if the Framer is in synchronization. Table 86 - Framing Bit Error Counter(Y17) (T1)
Bit 15-0
Name FC15 - 0
Bit 15-0
Name BPV15-0
Functional Description BPV Counter. 16 bit counter that is incremented for every bipolar violation error received. Table 87 - Bipolar Violation Counter(Y18) (T1)
Bit 15-0
Name CC15-0
Functional Description CRC-6 Error Counter Bits 15 to Zero. These are the 16 bits of the CRC-6 error counter. This is only relevant in the ESF Mode. This counter increments for every CRC-6 error. Table 88 - CRC-6 Error Counter(Y19) (T1)
Bit 15-8
Name OOF7 - 0
Functional Description Out Of Frame Counter. This eight bit counter is incremented with every loss of receive frame synchronization. Hence if you loss sync, gain sync and loss it again the counter will have a value of 2.
7-0
COFA7 - 0 Change of Frame Alignment Counter. This eight bit counter is incremented if a resynchronization is done which results in a shift in the frame alignment position. Table 89 - Out of Frame and Change of Frame Counters(Y1A) (T1)
Bit 15-8 7-0
Name # not used.
Functional Description
EXZ7-0 Excessive Zero Counter. This counter is incremented once for detection of 8 or more zeros if B8ZS is turned on. This counter is incremented once if 16 or more zeros are detected if B8ZS is turned off. This counter counts groups of 8 or more or 16 or more zeros separated by ones. Table 90 - Excessive Zero Counters(Y1B) (T1)
SEMICMF.019
119
MT9072
Bit 15-12 11 10 9 8 Name # RXclk TXclk Vcrc Vaddr not used. Functional Description
Data Sheet
This bit represents the receiver clock generated after the RXEN control bit, but before zero deletion is considered. This bit represents the transmit clock generated after the TXEN control bit, but before zero insertion is considered. This is the CRC recognition status bit for the receiver. Data is clocked into the register and then this bit is monitored to see if comparison was successful (bit will be high). This is the address recognition status bit for the receiver. Data is clocked into the Address Recognition Register and then this bit is monitored to see if comparison was successful (bit will be high). Transmit Byte Counter Position. These 7 bits provide the position of the Transmit HDLC Byte Counter register (YF6). The counter is decremented as a byte of data is sent through the Transmit FIFO. When this register reaches the count of one, the next write to the Tx FIFO will be tagged as an end of packet byte. The counter decrements at the end of the write to the Tx FIFO. If the Cycle bit of YF2 is set high, the counter will cycle through the programmed value continuously.
7-0
TBP7-0
Table 91 - Transmit Byte Counter Position and HDLC Test Status(Y1C) (T1) Bit 15-7 6 Name # IDC not used. Idle Channel State.Is set to a 1 when an idle Channel state (15 or more ones) has been detected at the receiver. This is an asynchronous event. On power reset, this may be 1 if the clock (RXC) was not operating. Status becomes valid after the first 15 bits or the first zero is received. RQ9-8Byte Status bits from RX FIFO. These bits determine the status of the byte to be read from RX FIFO as follows: 00 Packet Byte 01 First Byte 10 Last byte of good packet 11 Last byte of bad packet Functional Description
5-4
RQ9-8
3-2
TXSTAT1-0 Transmit FiFO Status: 00 Transmit FIFO is full. 01 The number of bytes in the transmit FIFO has reached or exceeded the 16 bytes threshold 10 Transmit FIFO is empty 11 The number of bytes in the TX FIFO is less than the 16 byte threshold. RXSTAT1-0 Receive FiFO Status: 00 Receive FIFO is empty. 01 The number of bytes in the Receive FIFO are less than the 16 bytes 10 Receive FIFO is full 11 The number of bytes in the Receive FIFO is greater than or equal to the 16 byte threshold. Table 92 - HDLC Status Word(Y1D) (T1)
1-0
120
SEMICMF.019
Data Sheet
Bit 15-0 Name RCRC15-0 Functional Description
MT9072
Received CRC. This register contains the CRC received from the transmitter. These bits are as the transmitter sent them, the LSB of the FCS sequence is MSB in this register. This register is updated at the end of each received packet and therefore should be read when end of packet is detected. Table 93 - HDLC Receive CRC(Y1E) (T1)
Bit 7-0
Name RXFIFO7-0
Functional Description Receive FIFO.This is the received data byte read from the RX FIFO. The status bits of this byte can be read from the status register. The FIFO status is not changed immediately when a write or read occurs. It is updated after the data has settled and the transfer to the last available position has finished. Note that if the HDLC receiver is connected to an receive T1 channel, the bit that arrived first is stored in the least significant bit of the receive FIFO. Table 94 - Receive FIFO(Y1F) (T1)
16.1.5
Latched Status Registers (Y20 - Y2F) Bit Functions
Tables 96 and 103 describe the bit functions of each of the Latched Status Registers in the MT9072 for T1. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 ... and Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11,A10 A9 A8). All latched status registers will be reset in the inactive state upon reset.
SEMICMF.019
121
MT9072
Bit 15-9 8 7 Name # GAL EOPDL not used. Functional Description
Data Sheet
Go Ahead received Latch. Indicates a go-ahead pattern (01111111) was detected by the HDLC receiver. This bit is cleared after a read of Y23 or Y33. End of Packet Data Latch. This bit is set when an end of packet (EOP) byte was written into the RX FIFO by the HDLC receiver. This can be in the form of a flag, an abort sequence or as an invalid packet. This bit is cleared after a read of Y23 or Y33. Transmit End of Packet Latch. This bit is set when the transmitter has finished sending the closing flag of a packet or after a packet has been aborted. This bit is cleared after a read of Y23 or Y33. End of Packet received latch. This bit is set when the byte about to be read from the RX FIFO is the last byte of the packet. It is also set if the Rx FIFO is read and there is no data in it. This bit is cleared after a read of Y23 or Y33. Transmit Fifo Low Latch. This bit is set when the Tx FIFO is emptied below the 16 byte low threshold level. This bit is cleared after a read of Y23 or Y33. Framer Abort Latch. This bit (FA) is set when a frame abort is received during packet reception. It must be received after a minimum number of bits have been received (26) otherwise it is ignored.This bit is cleared after a read of Y23 or Y33. Txunder Latch. This bit is set for a TX FIFO underrun indication. If high it indicates that a read by the transmitter was attempted on an empty Tx FIFO. This bit is cleared after a read of Y23 or Y33. Receive Fifo Full Latch. This bit is set when the Rx FIFO is filled above the 16 byte full threshold level. This bit is reset after a read.This bit is cleared after a read of Y23 or Y33. Receive Overflow Latch. Indicates that the 32 byte RX FIFO overflowed (i.e. an attempt to write to a 32byte full RX FIFO). The HDLC will always disable the receiver once the receive overflow has been detected. The receiver will be re-enabled upon detection of the next flag, but will overflow again unless the RX FIFO is read. This bit is reset after a read.This bit is cleared after a read of Y23 or Y33. Table 95 - HDLC Status Latch(Y23) (T1)
6
TEOPL
5
EOPRL
4 3
TXFLL FAL
2
TxunderL
1 0
RxffL RXOvfl
122
SEMICMF.019
Data Sheet
Bit 15 14 13 12 11 10 9 8 7 Name FEOL CRCOL OOFOL COFAOL BPVOL PRBSOL Functional Description
MT9072
Framing Bit Error Counter Overflow Latch. This bit is set when the framing bit counter(Y17) overflows. This bit is cleared after a read of Y24 or Y34. CRC-6 Error Counter Overflow Latch. This bit is set if the CRC6 error counter(Y19) overflows. This bit is cleared after a read of Y24 or Y34. Out Of Frame Counter Overflow Latch. This bit is set when the OOF counter(Y1A) overflows. This bit is cleared after a read of Y24 or Y34. Change of Frame Alignment Counter Overflow Latch. This bit is set when the change of frame alignment counter (Y1A) overflows. This bit is cleared after a read of Y24 or Y34. Bipolar Violation Counter Overflow Latch. This bit is set when the bipolar violation counter(Y18) overflows.This bit is cleared after a read of Y24 or Y34. Pseudo Random Bit Sequence Error Counter Overflow Latch. This bit is set when the PRBS error counter(Y15) overflows. This bit is cleared after a read of Y24 or Y34.
PRBSMFOL PRBS Multiframe Counter Overflow Latch. This bit is set when the PRBS multiframe counter(Y15) overflows. This bit is cleared after a read of Y24 or Y34. MFOOFOL Multiframe Out of Frame Counter Overflow Latch. This bit is set if the Multiframe Out of Frame Counter(Y16) overflows. This bit is cleared after a read of Y24 or Y34. TFSYNL Terminal Out Of Sync Latch. This bit is set when the terminal frame out of sync condition is acquired or lost. It is the latched version of the TFSYNC bit(Y10). This bit is cleared after a read of Y24 or Y34. Multiframes Out Of Sync Latch. This bit is set when the multiframes out of sync condition is acquired or lost. It is the latched version of the MFSYNC bit (Y10).This bit is cleared after a read of Y24 or Y34. Framing Bit Error Latch. This bit is set when a framing bit error is detected. It is cleared upon a read. It is the latched version of the Framing Bit Counter (Y17) event. This bit is cleared after a read of Y24 or Y34. Change of Frame Alignment Latch. This bit is set when the change of frame alignment occurs. This is the latched version of the count event to change of frame counter (Y1A). This bit is cleared after a read of Y24 or Y34. Severely Errored Frame Latch. This bit is set upon receipt of a line loopback disable code. This is a latched version of Y10. This bit is cleared after a read of Y24 or Y34. AIS Latch. This bit is set upon receipt of an AIS. This is a latched version of AIS(Y10).This bit is cleared after a read of Y24 or Y34. CRC Error Latched. This bit is set when the receive CRC error occurs. This bit is cleared after a read of Y24 or Y34. Digital Loss of Signal. This bit goes high after the detection of 192 or 32 consecutive zeros. This is the latched version of LOS(Y10). This bit is cleared after a read of Y24 or Y34. Table 96 - Receive Sync and Alarm Latch(Y24) (T1)
6
MFSYNL
5
FBEL
4
COFAL
3 2 1 0
SEFL AISL CRCL LOSL
SEMICMF.019
123
MT9072
Bit 15 14 13 Name D4YALML D4Y48L SECYELL Functional Description
Data Sheet
D4 Yellow Alarm Latch. This bit is set if a D4 yellow alarm is detected within a 600 millisecond integration period. This bit is cleared after a read of Y25 or Y35. D4 Yellow Alarm (48 milliseconds) Latch. This bit is set if a D4 yellow alarm is detected within a 48 millisecond integration period. This bit is cleared after a read of Y25 or Y35. Secondary D4 Yellow Alarm Latch. This bit is set if Secondary yellow alarm D4 (S bit in 12 th frame) is detected. It is cleared after a read.This bit is cleared after a read of Y25 or Y35. ESF Yellow Alarm Latch. This bit is set upon receipt of a ESF yellow alarm. This bit is cleared after a read of Y25 or Y35. T1DM Yellow Alarm Latched. If this bit is 1 a T1DM yellow alarm is received on bit 2 of 24th timeslot. This bit is cleared after a read of Y25 or Y35. not used. Bipolar Violation Latch. This bit is set when a bipolar violation occurs. This bit is cleared after a read of Y25 or Y35. PRBS Latch. This bit is set when a PRBS error has occured.This bit is cleared after a read of Y25 or Y35. Pulse Density Violation Latch. This bit is set when the receive PDV is detected.This bit is cleared after a read of Y25 or Y35. Line Loopback Enable Detect Latch. This bit is set upon receipt of a line loopback enable code. It is cleared after a read. This is a latched version of LLED(Y10).This bit is cleared after a read of Y25 or Y35. Line Loopback Disable Detect Latch. This bit is set upon receipt of a line loopback disable code. It is cleared after a read. This is a latched version of LLDD(Y10).This bit is cleared after a read of Y25 or Y35. Bit Oriented Message Latch. This bit is set if a bit oriented message has been received. It is cleared upon a read.This bit is cleared after a read of Y25 or Y35. Bit Oriented Message Match Latch. This bit is set if the bit oriented message received matches the value of the Bit Oriented Match register.This bit is cleared after a read of Y25 or Y35. Channel Associated signaling Received Latch. This bit is set if the received CAS has changed on any of the 24 channels.This bit is cleared after a read of Y25 or Y35. 1 Second Latch. This bit is set if the one second timer expires. This bit is cleared after a read of Y25 or Y35. 2 Second Latch. This bit is set if the two second timer expires. This bit is cleared after a read of Y25 or Y35. Table 97 - Receive Line Status and Timer Latch(Y25) (T1)
12 11 10 9 8 7 6
ESFYELL T1DMYL # BPVL PRBSL PDVL LLEDL
5
LLDDL
4 3
BOML BOMML
2 1 0
CASRL 1SECL 2SECL
124
SEMICMF.019
Data Sheet
Bit 15-4 3 2 1 0 Name # EXZOL EXZL TXSLIPL RXSLIPL not used. Functional Description
MT9072
Excessive Zero Overflow Latch. This bit goes high whenever the excessive zero counter (Y1B) is overflows. This bit is cleared after a read of Y26 or Y36. Excessive Zero Latch. This bit goes high whenever the excessive zero counter (Y1B) is incremeted by one. This bit is cleared after a read of Y26 or Y36. Transmit SLIP Latch. This bit goes high whenever a transmit slip occurs. This bit is cleared after a read of Y26 or Y36. Receive SLIP Latch. This bit goes high whenever a controlled frame slip occurs in the receive elastic buffer. This bit is cleared after a read of Y26 or Y36.
Table 98 - Elastic Store and Excessive Zero Status Latch(Y26) (T1)
Bit 15-0
Name
Functional Description
FCL<15:0> Framing Bit Error Count Latch. These bits make up a latch which samples the current value of the Framing Bit Error Counter (address Y17) on the rising edge of the internal one second timer. This latch is cleared with a RESET (RESET pin or RST bit). Table 99 - Framing Bit Error Count Latch(Y28) (T1)
Bit 15-0
Name
Functional Description
BPVL<15:0> Bipolar Violation Count Latch. These bits make up a latch which samples the current value of the Bipolar Violation Error Counter (address Y18) on the rising edge of the internal one second timer. This latch is cleared with a RESET (RESET pin or RST bit). Table 100 - Bipolar Violation Count Latch(Y29) (T1)
Bit 15-0
Name
Functional Description
CRCL<15:0> CRC-6 Error Count Latch. These bits make up a latch which samples the current value of the CRC Error Counter (address Y19) on the rising edge of the internal one second timer. This latch is cleared with a RESET (RESET pin or RST bit) Table 101 - CRC-6 Error Count Latch(Y2A) (T1)
SEMICMF.019
125
MT9072
Bit 15-8 Name OOFL<7:0> Functional Description
Data Sheet
Out of Frame Alignment Count Latch. These bits make up a latch which samples the current value of the Change of Frame Alignment Counter (address Y1A) on the rising edge of the internal one second timer. This latch is cleared with a RESET (RESET pin or RST bit).
7-0
COFAL<7:0> Change of Frame Alignment Count Latch. These bits make up a latch which samples the current value of the Change of Frame Alignment Counter (address Y1A) on the rising edge of the internal one second timer. This latch is cleared with a RESET (RESET pin or RST bit). Table 102 - Out of Frame Count and Change of Frame Count Latch(Y2B) (T1)
Bit 15-0
Name
Functional Description
MFOOFL<15:0> Multiframe OOF Count Latch. These bits make up a latch which samples the current value of the MFOOF Error Counter (address Y16) on the rising edge of the internal one second timer. This latch is cleared with a RESET (RESET pin or RST bit). Table 103 - Multiframe Out of Frame Count Latch(Y2C) (T1)
126
SEMICMF.019
Data Sheet
16.1.6 Interrupt Status Registers (Y30 - Y3F) Bit Functions
Interrupt status register bit functions are shown in Tables 105 to 108.
MT9072
Bit 15-9 8 7
Name # GAI EOPDI not used.
Functional Description
Go Ahead Interrupt. Indicates a go-ahead pattern (01111111) was detected by the HDLC receiver. This bit is reset after a read of Y33 or Y23. End of Packet Data Interrupt.This bit is set when an end of packet (EOP) byte was written into the RX FIFO by the HDLC receiver. This can be in the form of a flag, an abort sequence or as an invalid packet. This bit is reset after a read of Y33 or Y23. Transmit End of Packet Interrupt.This bit is set when the transmitter has finished sending the closing flag of a packet or after a packet has been aborted. This bit is reset after a read of Y33 or Y23. End of Packet Receive Fifo Interrupt.This bit is set when the byte about to be read from the RX FIFO is the last byte of the packet. It is also set if the Rx FIFO is read and there is no data in it.This bit is reset after a read of Y33 or Y23. Transmit FIFO Low Interrupt.This bit is set when the Tx FIFO is emptied below the 16 byte low threshold level.This bit is reset after a read of Y33 or Y23. Frame Abort: Transmit Interrupt. This bit (FA) is set when a frame abort is received during packet reception. It must be received after a minimum number of bits have been received (26) otherwise it is ignored. This bit is reset after a read of Y33 or Y23. Transmit Elastic Buffer Empty Interrupt. If high it Indicates that a read by the transmitter was attempted on an empty Tx FIFO. This bit is reset after a read of Y33 or Y23. Receive FIFO is filled above Threshold Interrupt.This bit is set when the Rx FIFO is filled above the 16 byte full threshold level. This bit is reset after a read of Y33 or Y23. Receive Fifo Overflow Interrupt This bit Indicates that the 32 byte RX FIFO overflowed (i/.e. an attempt to write to a 32 byte full RX FIFO). The HDLC will always disable the receiver once the receive overflow has been detected. The receiver will be re-enabled upon detection of the next flag, but will overflow again unless the RX FIFO is read. This bit is reset after a read of Y33 or Y23. Table 104 - HDLC Interrupt Status Register(Y33) (T1)
6
TEOPI
5
EOPRI
4 3
TXFLI FAI
2
TXUNDERI
1 0
RXFFI RXOVFLI
16.1.7
Interrupt Mask Registers (Y40 - Y4F) Bit Functions
Tables 109 to 115 describe the bit functions of each of the Interrupt Mask Registers in the MT9072. Each register is repeated for each of the 4 framers (not the Interrupt Vector Mask). Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2. and Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11 A10 A9 A8). In addition, a simultaneous write to all 8 Framers is possible by setting the A11 address to Y=8 (1000). A (0) or (1) in the "Name" column of these tables indicates the state of the data bits after a hard reset (the RESET pin is toggled from zero to one), or a software reset (the RST bit in control register address YF1 is toggled from one to zero) or a T1E0 write to the Global Control Register bit 15.
SEMICMF.019
127
MT9072
Bit 15-9 8 7 6 Name # GAIM (0) EOPDIM (0) TEOPIM (0) EOPRIM (0) TXFLIM (0) FAIM (0) not used. Functional Description
Data Sheet
Go Ahead Interrupt Mask. When unmasked an interrupt is generated when go-ahead pattern (01111111) was detected by the HDLC receiver. End of Packet Data Interrupt Mask. When unmasked an interrupt is initiated when an end of packet (EOP) byte was written into the RX FIFO by the HDLC receiver. Transmit End of Packet Interrupt Mask. When unmasked an interrupt is initiated when the transmitter has finished sending the closing flag of a packet or after a packet has been aborted. End of Packet Received Interrupt Mask. When unmasked an interrupt is initiated when the byte about to be read from the RX FIFO is the last byte of the packet. An interrupt is also initiated if the Rx FIFO is read and there is no data in it. Transmit Fifo Low Interrupt Mask. When unmasked an interrupt is initiated when the Tx FIFO is emptied below the selected low threshold level. Frame Abort: Transmit Interrupt Mask. When unmasked an interrupt is initiated this bit (FA) is set when a frame abort is received during packet reception. It must be received after a minimum number of bits have been received (26) otherwise it is ignored.
5
4 3
2 1 0
TXUNDERIM Transmit Fifo Underrun Interrupt Mask. When unmasked an interrupt is initiated for TX (0) FIFO underrun indication. RXFFIM (0) RXOVFLIM (0) Receive Fifo full Threshold interrupt Mask. When unmasked an interrupt is initiated whenever the Rx FIFO is filled above the 16 byte threshold level. Receive Fifo Overflow Interrupt Mask. When unmasked an interrupt is initiated whenever the 32 byte RX FIFO overflowed (i.e. an attempt to write to a 32 byte full RX FIFO). Table 105 - HDLC Interrupt Mask Register(Y43) (T1)
Bit 15
Name FEOIM (0) CRCOIM (0) OOFOIM (0) COFAOIM (0) BPVOIM (0)
Functional Description Framing Bit Error Counter Overflow Interrupt Mask. When unmasked an interrupt is initiated whenever the framing bit error counter changes from FFH to 00H. 1 -masked, 0 unmasked. CRC-6 Error Counter Overflow Interrupt Mask. When unmasked an interrupt is initiated whenever the CRC-6 error counter changes from FFH to 00H. 1 - masked, 0 - unmasked. Out Of Frame Counter Overflow Interrupt Mask. When unmasked an interrupt is initiated whenever the out of frame counter changes state from changes from FFH to 00H. 1 - masked, 0 - unmasked. Change of Frame Alignment Counter Overflow Interrupt Mask. When unmasked an interrupt is initiated whenever the change of frame alignment counter changes from FFH to 00H. 1 - masked, 0 - unmasked. Bipolar Violation Counter Overflow Interrupt Mask. When unmasked an interrupt is initiated whenever the bipolar violation counter changes from FFH to 00H. 1- masked, 0 unmasked. Table 106 - Receive and Sync Interrupt Mask Register(Y44) (T1)
14 13
12
11
128
SEMICMF.019
Data Sheet
Bit 10 Name PRBSOIM (0) Functional Description
MT9072
Pseudo Random Bit Sequence Error Counter Overflow Interrupt Mask. When unmasked an interrupt will be generated whenever the PRBS error counter changes from FFH to 00H. 1 - masked, 0 -unmasked.
9
PRBSMFOIM Pseudo Random Bit Sequence Multiframe Counter Overflow Interrupt Mask. When (0) unmasked an interrupt will be generated whenever the multiframe counter attached to the PRBS error counter overflows. FFH to 00H. 1 - masked, 0 - unmasked. MFOOFOIM Multiframes Out Of Sync Overflow Interrupt Mask. When unmasked an interrupt will be (0) generated when the multiframes out of frame counter changes from FFH to 00H. 1 masked, 0 - unmasked. TFSYNIM (0) MFSYNIM (0) FBEIM (0) BOMIM (0) Terminal Frame Synchronization Interrupt Mask. When unmasked an interrupt is initiated when a loss of terminal frame synchronization condition exists. If 1 - masked, 0 unmasked. Multiframe Synchronization Interrupt Mask. When unmasked an interrupt is initiated when a loss of multiframe synchronization condition exist. If 1 - masked, 0 - unmasked. Framing Bit Error Interrupt Mask. When unmasked an interrupt is initiated whenever an erroneous framing bit is detected (if circuit is in terminal frame sync). 1-masked, 0unmasked. Bit Oriented Message Interrupt. When unmasked an interrupt is initiated whenever a pattern 111111110xxxxxx0 has been received on the FDL that is different from the last message. The new message must persist for 8 out the last 10 message positions to be accepted as a valid new message. 1 -masked, 0 - unmasked. Bit Oriented Message Match Interrupt. When unmasked an interrupt is initiated whenever a pattern 111111110xxxxxx0 has been received on the FDL that is different from the last message and matches the contents of Bit Oriented Message Match Register. The new message must persist for 8 out the last 10 message positions to be accepted as a valid new message. 1 -masked, 0 - unmasked. Receive Channel Associated Signaling(CAS) Change Interrupt. When unmasked an interrupt is initiated whenever a change of state (optionally debounced - see RSDB in signaling Control Word) is detected in the signaling bits (AB or ABCD) pattern. One Second Interrupt Status. When unmasked an interrupt is initiated whenever the 1 SEC status bit goes from low to high. This bit is reset after a read of Y35 or Y25. Two Second Interrupt Status. When unmasked an interrupt is initiated whenever the 2SEC status bit goes from low to high. This bit is reset after a read of Y35 or Y25. Table 106 - Receive and Sync Interrupt Mask Register(Y44) (T1)
8
7
6 5
4
3
BOMMI (0)
2
CASRI (0) 1SECI (0) 2SECI (0)
1 0
.
SEMICMF.019
129
MT9072
Bit 15 14 13 12 11 10 9 Name D4YALMIM (0) D4Y48IM (0) SECYELIM (0) ESFYELIM (0) T1DMYIM (0) # BPVIM (0) PRBSIM (0) PDVIM (0) Functional Description
Data Sheet
D4 Yellow Interrupt Mask. When unmasked this interrupt bit goes high whenever the D4 Yellow alarm code has been received. If 1 - masked, 0 - unmasked. D4 Y48 Interrupt Mask. When unmasked this interrupt bit goes high whenever the D4 Yellow alarm code has been received for 48 msec. If 1 - masked, 0 - unmasked. Secondary Yellow Interrupt Mask. When unmasked this interrupt bit goes high whenever a Secondary Yellow alarm is received. If 1 - masked, 0 - unmasked. ESF Yellow Interrupt Mask. When unmasked this interrupt bit goes high whenever a ESF Yellow alarm is received. If 1 - masked, 0 - unmasked. T1DM Yellow Interrupt Mask. When unmasked this interrupt bit goes high whenever a TIDM Yellow alarm is received. If 1 - masked, 0 - unmasked. not used Bipolar Violation Interrupt Mask. When unmasked this interrupt bit goes high whenever a bipolar violation (excluding B8ZS encoding) is encountered. If 1 - masked, 0 unmasked. Pseudo Random Bit Sequence Error Interrupt Mask. When unmasked this interrupt bit goes high upon detection of an error with a channel selected for PRBS testing. If 1 masked, 0 - unmasked. Pulse Density Violation Interrupt Mask. When unmasked this interrupt bit goes high whenever a sequence of 16 consecutive zeros is received on the line, or the incoming pulse density is less than N ones in a time frame of 8(N+1) where N = 1 to 23. If 1 masked, 0 - unmasked. Loop Code Enable Detected Interrupt Mask. When unmasked this interrupt bit goes high whenever the loop up code has been detected on the line for a period of 48 milliseconds. If 1 - masked, 0 - unmasked. Loop Code Disable Detected Interrupt Mask. When unmasked this interrupt bit goes high whenever the loop down code has been detected on the line for a period of 48 milliseconds. If 1 - masked, 0 - unmasked.
8
7
6
LLEDIM (0) LLDDIM (0)
5
Table 107 - Receive Line and Timer Interrupt Mask Register(Y45) (T1)
Bit 15-4 3 2 1 0
Name # EXZOI (0) EXZI (0) TXSLIPIM (0) RXSLIPIM (0) not used.
Functional Description
Excessive Zero Overflow Interrupt. This bit goes high whenever the excessive zero counter (Y1B) overflows.This bit is reset after a read of Y36 or Y26. EXcessive Zero Interrupt. This bit goes high whenever the excessive zero counter (Y1B) is incremeted by one. This bit is reset after a read of Y36 or Y26. Transmit SLIP Interrupt Mask. When unmasked an interrupt is initiated whenever a controlled frame slip occurs in the transmit elastic buffer. If 1 - masked, 0 - unmasked. Receive SLIP Interrupt Mask. When unmasked an interrupt is initiated whenever a controlled frame slip occurs in the receive elastic buffer. If 1 - masked, 0 - unmasked.
Table 108 - Elastic Store and Excessive zero Interrupt Mask Register(Y46) (T1)
130
SEMICMF.019
Data Sheet
16.1.8 Per Channel Control and Data (Y50 - YAF) Bit Functions
MT9072
Tables 112 to 114 provide the per timeslot control for signaling and Per Channel Control. The reset values of Per channel Transmit signaling and Receive signaling bits mcan be 1 or 0.
Bit 15-4 3
Name # TA(n) not used.
Functional Description
Transmit Signaling Bits A for Channel n. Where signaling is enabled, these bits are transmitted in bit position 8 of the 6th DS1 frame (within the 12 frame superframe structure for D4 superframes and the 24 frame structure for ESF superframes). This data is obtained from the CSTi interface but can be overwritten via the Micro port for trunk conditioning applications. If the MPST bit in the corresponding per timeslot control is not set, this value will be constantly overwritten by the CSTi stream. Transmit Signaling Bits B for Channel n. Where signaling is enabled, these bits are transmitted in bit position 8 of the 12th DS1 frame (within the 12 frame superframe structure for D4 superframes and the 24 frame structure for ESF superframes).This data is obtained from the CSTi interface but can be overwritten via the Micro port for trunk conditioning applications. If the MPST bit in the corresponding per timeslot control is not set, this value will be constantly overwritten by the CSTi stream. Transmit Signaling Bits C for Channel n. Where signaling is enabled, these bits are transmitted in bit position 8 of the 18th DS1 frame within the 24 frame structure for ESF superframes. In D4 mode these bits are unused. This data is obtained from the CSTi interface but can be overwritten via the Micro port for trunk conditioning applications. If the MPST bit in the corresponding per timeslot control is not set, this value will be constantly overwritten by the CSTi stream. Transmit Signaling Bits D for Channel n. Where signaling is enabled, these bits are transmitted in bit position 8 of the 24th DS1 frame within the 24 frame structure for ESF superframes. In D4 mode these bits are unused.This data is obtained from the CSTi interface but can be overwritten via the Micro port for trunk conditioning applications. If the MPST bit in the corresponding per timeslot control is not set, this value will be constantly overwritten by the CSTi stream. Table 109 - Per Channel Transmit Signaling Y50-Y67 (T1)
2
TB(n)
1
TC(n)
0
TD(n)
SEMICMF.019
131
MT9072
Bit 15 - 4 3 Name # not used. Functional Description
Data Sheet
RA(n) Receive Signaling Bits A for Channel n. Where signaling is enabled, these bits are received in bit position 8 of the 6th DS1 frame (within the 12 frame superframe structure for D4 superframes and the 24 frame structure for ESF superframes).This data can be overwritten by the microport for trunk conditioning applications. RB(n) Receive Signaling Bits B for Channel n. Where signaling is enabled, these bits are received in bit position 8 of the 12th DS1 frame (within the 12 frame superframe structure for D4 superframes and the 24 frame structure for ESF superframes).This data can be overwritten by the microport for trunk conditioning applications. RC(n) Receive Signaling Bits C for Channel n. Where signaling is enabled, these bits are transmitted in bit position 8 of the 18th DS1 frame within the 24 frame structure for ESF superframes. In D4 mode these bits are unused.This data can be overwritten by the microport for trunk conditioning applications RD(n) Receive Signaling Bits D for Channel n. Where signaling is enabled, these bits are transmitted in bit position 8 of the 24th DS1 frame within the 24 frame structure for ESF superframes. In D4 mode these bits are unused.This data is obtained from the CSTi interface but can be overwritten via the Micro port for trunk conditioning applications.This data can be overwritten by the microport for trunck conditioning applications. Table 110 - Per Channel Receive Signaling Y70-Y87 (T1)
2
1
0
132
SEMICMF.019
Data Sheet
Bit 15-10 9 8 Name # RPCI (0) MPDR (0) MPST not used. Functional Description
MT9072
Receive Per Channel Inversion. The data received from the incoming DS1 channel is inverted before it emerges from DSTo if this bit is set for the channel. Micro Port Data Receive. Setting this bit allows for the receive data for a given channel to be replaced by data in the idle code(Y09). The idle code can be written by the micro port for trunk conditioning applications. Micro Port Signaling Transmit. Setting this bit allows for the transmit signaling for a given channel to be replaced by the bits in the Per Channel Transmit signaling Registration-TD of registers Y50-Y67. They can be written by the micro port for trunk conditioning applications. Transmit Per Channel Inversion. When set high the data for this channel sourced from DSTi is inverted before being transmit onto the equivalent DS1 channel. Remote Timeslot Loopback. If one, the corresponding DS1 receive timeslot is looped to the corresponding DS1 transmit timeslot. This received timeslot will also be present on DSTo. If zero, the receive loopback is disabled. Local Timeslot Loopback. If one, the corresponding transmit timeslot is looped to the corresponding receive timeslot. This transmit timeslot will also be present on the transmit DS1 stream. If zero, this loopback is disabled. Transmit Test. If one the Mu-law digital milliwatt (where control bit ADSEQ is one) or a PRBS generator (215-1) (ADSEQ is zero) will be transmitted in the corresponding DS1 timeslot. More than one timeslot may be activated at once. If zero, the test signal will not be connected to the corresponding timeslot. Receive Test. If one, the Mu-law digital milliwatt (where control bit ADSEQ is one) will be sent to the DSTo or a PRBS data (215-1) (if ADSEQ is zero) will be expected in the corresponding PCM 24 timeslot. If zero, the PRBS detector will not be connected to the corresponding timeslot. Micro Port Data Transmit. Setting this bit allows for the transmit data for a given channel to be replaced by the idle code(Y0A). The idle code can be written by the micro port for trunk conditioning applications. Ensure that TTST and RTSL are off. Clear Channel. When set high no robbed bit signaling is inserted in the equivalent transmit DS1 channel. When set low robbed bit signaling is included in every 6th frame. Table 111 - Per Channel Control Word(Y90-YA7) (T1)
7
6 5
TPCI (0) RTSL (0) LTSL (0) TTST (0)
4
3
2
RRST (0)
1
MPDT (0) CC (0)
0
16.1.9
Master Control Registers (YF1 to YF7) Bit Functions
Tables 116 to 122 describe the bit functions of each of the Master Control Registers in the MT9072 for T1 mode. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2,... Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11 A10 A9 A8). In addition, a simultaneous write to all 8 Framers is possible by setting the address A11 to 1 and A10 to A8 to 0. A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a hard reset (the RESET pin is toggled from zero to one), or a software reset (the RST bit in control register address YF1 is toggled from one to zero or toggling of RSTC in Global Control Register). The (#) indicates that a (0) or (1) is possible.
SEMICMF.019
133
MT9072
Bit 15-11 10 Name # Tx8KEN (0) not used. Functional Description
Data Sheet
Transmit 8 KHz Enable. If one, the pin RxMF transmits a positive 8 KHz frame pulse synchronous with the serial data stream TPOS/TNEG. If zero, the pin RxMF transmits a negative frame pulse synchronous with the multiframe boundary of data coming out of DSTo. Receive DSTo All Ones. If one, the DSTo pin operates normally. If zero, all timeslots (0-31) of DSTo are set to one.
9 8
RxDO (0)
TXMFSEL Transmit Multiframe Select. This bit is used to select if the framer is used for application of (0) the TXMF pulse which sets the multiframe boundary for the T1 transmitters. A one will select the framer for application of TXMF. SPND (0) INTA (0) Suspend Interrupts. If zero, the IRQ output will be in a high-impedance state and all interrupts will be ignored. If one, the IRQ output will function normally. Interrupt Acknowledge. All interrupt and latched status registers for a particular framer may be cleared (without reading the interrupt status registers) by setting the INTA control bit to zero. Interrupt status registers for a particular framer will be cleared (and not updated) as long as INTA is low. The framers interrupt vector bits will remain at zero, therefore that framer cannot toggle the IRQ pin. DSTo Enable. If zero, pin DSTo is tristate. If set, pin DSTo is enabled. CSTo Enable. If zero, pin CSTo is tristate. If set, pin CSTo is enabled. Receive CSTo All Ones.If one, the CSTo pin operates normally. If zero all timeslots of CSTo are set to one Counter Clear. When this bit is changed from zero to one, all non-latched status counters (address Y15 to Y1A) are cleared. If zero, all non-latched status counters operate normally. One Second Sample. Setting this bit causes the latched error counters(Y28 to Y2C) (change of frame alignment, loss of frame alignment, bpv errors, crc errors, severely errored frame events and multiframes out of sync) to be updated on one second intervals coincident with the one second timer (Y11). Reset. When this bit is changed from zero to one, the selected framer (Y) will reset to its default mode. The default mode will depend on the T1E0 bit(Global control0 bit 15). Any write to his bit should be followed by 125 usec before initialization of per timeslot control etc. See the Reset Operation section for the default settings. Table 112 - Interrupt and I/O Control(YF1) (T1)
7 6
5 4 3 2 1
DSToEN (0) CSToEN (0) RxCO (0) CNTCLR (0) SAMPLE (0)
0
RST (0)
134
SEMICMF.019
Data Sheet
Bit 15-11 10 Name # ADREC (0) RXEN (0) not used. Functional Description
MT9072
Address Recognition.When high, this bit will enable address recognition. This forces the receiver to recognize only those packets having the unique address as programmed in the Receive Address Recognition Registers or if the address is an All Call Address. Receive Enable.When low this bit will disable the HDLC receiver. The receiver will disable after the rest of the packet presently being received is finished. The receiver's internal clock is disabled. When high the receiver will be immediately enabled (depending on the state of RXCEN input) and will begin searching for flags, Go-aheads etc. Transmit Enable.When low this bit will disable the HDLC transmitter. The transmitter will disable after the completion of the packet presently being transmitted. The transmitter's internal clock is disabled. When high the transmitter will be immediately enabled (depending on the state of the TXCEN input) and will begin transmitting data, or go to a mark idle or interframe time fill state. End of Packet When set this bit will indicate an end of packet byte to the transmitter, which will transmit an FCS following this byte. This facilitates loading of multiple packets into TX FIFO. Reset automatically after a write to the TX FIFO occurs. Framer Abort.Forms a tag on the next byte written to the TX FIFO, and when set will indicate to the transmitter that it should abort the packet in which that byte is being transmitted. Reset automatically after a write to the TX FIFO. Mark-Idle.When low, the transmitter will be in an idle state. When high it is in an interframe time fill state. These two states will only occur when the TX FIFO is empty. Cycle.When high, this bit will cause the transmit byte count to cycle through the value loaded into the Transmit Byte Count Register. Transmit CRC Inhibit. When high, this bit will inhibit transmission of the CRC. That is, the transmitter will not insert the computed CRC onto the bit stream after seeing the EOP tag byte. This is used in V.120 terminal adaptation for synchronous protocol sensitive UI frames. Seven.When high, this bit will enable seven bits of address recognition in the first address byte. The received address byte must have bit 0 equal to 1 which indicates a single address byte is being received. Rx Fifo Reset.When high, the RX FIFO will be reset. This causes the receiver to be disabled until the next reception of a flag. The status register will identify the FIFO as being empty. However, the actual bit values in the RX FIFO will not be reset. Transmit FIFO Reset When high, the TX FIFO will be reset. The Status Register will identify the FIFO as being empty. This bit will be reset when data is written to the TX FIFO. However, the actual bit values of data in the TX FIFO will not be reset. Table 113 - HDLC Control 1(YF2) (T1)
9
8
TXEN (0)
7
EOP (0) FA (0) MI (0) CYCLE (0) TCRCI (0) SEVEN (0) RXFRST (0) TXFRST (0)
6
5 4 3
2
1
0
SEMICMF.019
135
MT9072
Bit 15-6 5 Name # HRST (0) not used. Functional Description
Data Sheet
HDLC Reset. When this bit is high, the HDLC and HDLC registers will be reset (HDLC Control, HDLC Test Control, Address Recognition Byte). This is similar to RESET being applied, the only difference being that this bit will not be reset. This bit can only be reset by writing a zero to this location or applying RESET.
4
RTLOOP Receive Transmit Loopback. When this bit is high, receive to transmit HDLC loopback will (0) be activated. Receive data, including end of packet indication, but not including flags or CRC, will be written to the TX FIFO as well as the RX FIFO. When the transmitter is enabled, this data will be transmitted as though written by the microprocessor. Both good and bad packets will be looped back. Receive to transmit loopback may also be accomplished by reading the RX FIFO using the microprocessor and writing these bytes, with appropriate tags, into the TX FIFO. CRCTST CRC Test. This bit allows direct access to the CRC Comparison Register in the receiver (0) through the serial interface. After testing is enabled, serial data is clocked in until the data aligns with the internal comparison (16 RXC clock cycles) and then the clock is stopped. The expected pattern is F0B8 hex. Each bit of the CRC can be corrupted to allow more efficient testing. FTST (0) Fifo Test. This bit allows the writing to the RX FIFO and reading of the TX FIFO through the microprocessor to allow more efficient testing of the FIFO status/interrupt functionality. This is done by making a TX FIFO write become a RX FIFO write and a RX FIFO read become a TX FIFO read. In addition, EOP/FA and RQ8/RQ9 are re-defined to be accessible (i.e. RX write causes EOP/FA to go to RX fifo input; TX read looks at output of TX fifo through RQ8/RQ9 bits). Address Recognition Test. This bit allows direct access to the Address Recognition Registers in the receiver through the serial interface to allow more efficient testing. After address testing is enabled, serial data is clocked in until the data aligns with the internal address comparison (16 RXc clock cycles) and then clock is stopped. Then the VADDR bit in Y1C can be checked. HDLC Loopback. When high, transmit to receive HDLC loopback will be activated. The packetized transmit data will be looped back to the receive input. RXEN and TXEN bits must also be enabled. Table 114 - HDLC Test Control(YF3) (T1)
3
2
1
ADTST (0)
0
HLOOP (0)
136
SEMICMF.019
Data Sheet
Bit 15-9 Name ADM26 ADM20 (0000000) A2EN (0) Functional Description
MT9072
Address Mask 26 to Address Mask 20. A seven bit mask used to interrogate the second byte of the received address. Adr26 is the MSB. This mask is ignored (as well as first byte mask) if all call address (1111111) is received. Address 2 Enable. When this bit is high, this seven bit mask is used in address comparison of the second address byte. If address recognition is enabled, any packet failing the address comparison will not be stored in the RX FIFO. A2en must be high for All-call address recognition. When this bit is low, this bit mask is ignored in address comparison Address Mask 16 to Address Mask 11.A six bit mask used to interrogate the first byte of the received address. AdrM16 is MSB.
8
7-2
ADRM16 ADRM11 (000000) ADRM10 (0) A1EN (0)
1 0
Address 10 Mask.This bit is used in address comparison if a seven bit address is being checked for (YF2 bit 'Seven' is set). Address 1 Enable.When this bit is high, this six (or seven) bit mask is used in address comparison of the first address byte. If address recognition is enabled, any packet failing the address comparison will not be stored in the RX FIFO. A1en must be high for All-call (1111111) address recognition for single byte address. When this bit is low, this bit mask is ignored in address comparison. Table 115 - Address Recognition Register(YF4) (T1)
Bit 15-8 7-0
Name # BIT7-0 (00000000) not used.
Functional Description
This eight bit word is tagged with the two status bits from control register 1 (EOP and FA), and the resulting 10 bit word is written to the TX FIFO. The FIFO status is not changed immediately after a write or read occurs. It is updated after the data has settled and the transfer to the last available position has finished. Note that when the HDLC is connected to a T1 channel, the least significant bit in the FIFO is sent first. Table 116 - TX Fifo Write Register(YF5) (T1)
Bit 15-8 7-0
Name # CNT7-0 (00000000) not used.
Functional Description
The Transmit Byte Count Register indicating the length of the data portion of the packet about to be transmitted. This is the size of the data and not the address, flags or FCS. The Transmit Byte Counter position Y1C determines the number of bytes that have been sent from the Transmit FIFO. Table 117 - TX Byte Count Register(YF6) (T1)
SEMICMF.019
137
MT9072
Bit 15-8 7-0 Name # not used. Functional Description
Data Sheet
TxSD7-0 Transmit Set Delay Bits 7 - 0. Writing to this register forces a one time setting of the (00000000) delay through the transmit slip buffer. The binary value written to the Transmit Set Delay Bits defines the delay between the write of the Transmit ST-BUS Channel containing DS1 timeslot 1 (first timeslot) and its read from the slip buffer. If the value written to the Transmit Set Delay Bits is 00H to BFH then the delay can be calculated as: (Value) / (1.544 x 106) seconds. If the value written to the Transmit Set Delay Bits is C0H to FFH then the delay can be calculated as: (255 - value) / (2.048 x 106) seconds. After a reset there will be an immediate transmit slip and the subsequent delay through the transmit slip buffer will be one frame. Table 118 - TX Set Delay Bits (YF7) (T1)
16.1.10
Global Control and Status Registers (900 - 91F) Bit Functions
The Global Control and Status Registers are common to the T1 and E1 operation. The global registers are accessed by address hex 9xx ( A11 and A8 being high and A10 and A9 being low) Bit 15 Name T1E0 (1) Functional Description T1E0. This bit determines if the chip will operate in T1 or E1 mode for all 8 framers. If the value of this bit is changed the chip is reset in E1 or T1 default register mode. If the bit is set to 1, all the framer register values are set to T1 defaults. For a setting of 0 the register values are set to E1 defaults. This action takes approximately 34 1.5444 clock cycles. Hence any writes to registers should be done on the next 125 usec frame after setting or clearing this bit. ST-BUS Enable. If zero, ST-BUS timing is enabled. If one, GCI timing is enabled (only available for 2.048Mb/s mode). See Figures 24-31. not used. Clock Rate. This clock select bit determines the system clock at the CKi pin and the receive frame pulse at the FPi pin as follows (See Figures 24 to 31): CK1 Clock Frame Pulse System Bus 0 4.096MHz 2.048Mb/s 2.048Mb/s 1 16.384MHz 8.192Mb/s 8.192Mb/s not used. Common Reset. When this bit is changed from zero to one, all eight framers will reset to their default T1 mode. This software reset has the same effect as the RESET pin. See the Reset Operation section for the default settings. Table 119 - Global Control0 Register (R/W Address 900) (T1)
14 13-5 4
STBUS (0) # CK1 (0)
3-1 0
# RSTC (0)
138
SEMICMF.019
Data Sheet
Bit 15-11 10-8 7-6 Name Functional Description
MT9072
CHANNUM Channel Number.These 5 bits determine the channel that is used for updating of the ST(00000) Bus Analyzer buffer. # STRNUM (00000) not used. Stream Number. These 5 bits determine the streams that will be used as the source data for the ST-Bus Analyzer buffer. 00: DSTi 01: DSTo 10: CSTi 11: CSTo
5
STBUFEN ST-BUS Analyser Buffer Enable. Setting this bit enables the ST-BUS Analyser Buffer (0) update. When the user reads the buffer (920-93F), this bit must be 0. Any reads of the buffer while this bit is set does not ensure correct data being read. FNUM (2:0) (000) CHUP (0) Framer Number 0 to 7
4-2
1
Channel Update. If 0 the update of the memory is at frame rate for a given channel. The channel selected for update is provided by the ChanNum bits of this register. If set the complete frame (channels 0 to 32) are updated to the buffer.
0
CONTSIN Continuous Single. If set to 1 the ST-BUS Analyzer buffer is updated continuously. If set (0) to zero the buffer is updated once and stopped. An optional interrupt can be generated once the buffer is fulla. Table 120 - Global Control1 Register (R/W Address 901) (T1)
a. The ST-BUS Analyser can be used in continuous acquisition mode without any problem (Register 901, bit 0 is set). If the ST-BUS analyser is used in the single mode (Register 901, bit 0 is cleared) an interrupt generated cannot be cleared and the MT9072 has to be reset.
Bit 15
Name
Functional Description
F3HM Framer 3 HDLC Mask. This is the mask bit for the F3HVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F3EM Framer 3 Elastic Mask. This is the mask bit for the F3EVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F3RM Framer 3 Rx Line Mask. This is the mask bit for the F3RVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. Table 121 - Interrupt Vector 1 Mask Register (Address 902) (T1)
14
13
SEMICMF.019
139
MT9072
Bit 12 Name Functional Description
Data Sheet
F3SM Framer 3 Sync and Overflow Mask. This is the mask bit for the F3SVS status bit in the Interrupt (0) Vector Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F2HM Framer 2 HDLC Mask. This is the mask bit for the F2HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F2EM Framer 2 Elastic Mask. This is the mask bit for the F2EVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F2RM Framer 2 Rx Line Mask. This is the mask bit for the F2RVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F2SM Framer 2 Sync and Overflow Mask. This is the mask bit for the F2SVS status bit in the Interrupt (0) Vector Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F1HM Framer 1 HDLC Mask. This is the mask bit for the F1HVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F1EM Framer 1 Elastic Mask. This is the mask bit for the F1EVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F1RM Framer 1 Rx Line Mask. This is the mask bit for the F1RVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F1SM Framer 1 Sync and Overflow Mask. This is the mask bit for the F1SVS status bit in the Interrupt (0) Vector Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F0HM Framer 0 HDLC Mask. This is the mask bit for the F0HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. Table 121 - Interrupt Vector 1 Mask Register (Address 902) (T1)
11
10
9
8
7
6
5
4
3
140
SEMICMF.019
Data Sheet
Bit 2 Name Functional Description
MT9072
F0EM Framer 0 Elastic Mask. This is the mask bit for the F0EVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F0RM Framer 0 Rx Line Mask. This is the mask bit for the F0RVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F0SM Framer 0 Sync and Overflow Mask. This is the mask bit for the F0SVS status bit in the Interrupt (0) Vector Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. Table 121 - Interrupt Vector 1 Mask Register (Address 902) (T1)
1
0
Bit 15
Name
Functional Description
F7HM Framer 7 HDLC Mask. This is the mask bit for the F7HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F7EM Framer 7 Elastic Mask. This is the mask bit for the F7EVS status bit in the Interrupt Vector (0) Register(address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F7RM Framer 7 Rx Line Mask. This is the mask bit for the F7RVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F7SM Framer 7 Sync and Overflow Mask. This is the mask bit for the F7SVS status bit in the Interrupt (0) Vector Register(address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F6HM Framer 6 HDLC Mask. This is the mask bit for the F6HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F6EM Framer 6 Elastic Mask. This is the mask bit for the F6EVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F6RM Framer 6 Rx LineMask. This is the mask bit for the F6RVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. Table 122 - Interrupt Vector 2 Mask Register (Address 903) (T1)
14
13
12
11
10
9
SEMICMF.019
141
MT9072
Bit 8 Name Functional Description
Data Sheet
F6SM Framer 6 Sync and Overflow Mask. This is the mask bit for the F6SVS status bit in the Interrupt (0) Vector Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F5HM Framer 5 HDLC Mask. This is the mask bit for the F5HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F5EM Framer 5 Elastic Mask. This is the mask bit for the F5EVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F5RM Framer 5 Rx Line Mask. This is the mask bit for the F5RVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F5SM Framer 5 Sync and Overflow Mask. This is the mask bit for the F5SVS status bit in the Interrupt (0) Vector Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F4HM Framer 4 HDLC Mask. This is the mask bit for the F5HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F4EM Framer 4 Elastic Mask. This is the mask bit for the F4EVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F4RM Framer 4 Rx Line Mask. This is the mask bit for the F4RVS status bit in the Interrupt Vector (0) register(address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F4SM Framer 4 Sync and Overflow Mask. This is the mask bit for the F4SVS status bit in the Interrupt (0) Vector Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. Table 122 - Interrupt Vector 2 Mask Register (Address 903) (T1)
7
6
5
4
3
2
1
0
142
SEMICMF.019
Data Sheet
Bit 15 14 13 12 11 10 Name Functional Description
MT9072
SLBK8 ST-BUS Loopback 8M All. If one, DSTo[0] is connected to DSTi[4], and DSTo[4] is connected (0) to DSTi[0]. This can be used in 8.192 Mbit/s or 2.048 Mbit/s mode. See Loopbacks section. SLBK67 ST-BUS Loopback Framer 6 & 7. If one, DSTo[6] is connected to DSTi[7], and DSTo[7] is (0) connected to DSTi[6]. Used only in 2.048Mb/s mode. See Loopback section for details. SLBK45 ST-BUS Loopback Framer 4 & 5. If one, DSTo[4] is connected to DSTi[5], and DSTo[5] is (0) connected to DSTi[4]. Used only in 2.048Mb/s mode. See Loopbacks section. SLBK23 ST-BUS Loopback Framer 2 & 3. If one, DSTo[2] is connected to DSTi[3], and DSTo[3] is (0) connected to DSTi[2]. Used only in 2.048Mb/s mode. See Loopbacks section. SLBK01 ST-BUS Loopback Framer 0 & 1. If one, DSTo[0] is connected to DSTi[1], and DSTo[1] is (0) connected to DSTi[0]. Used only in 2.048Mb/s mode. See Loopbacks section. RLBK8 Remote Loopback 8 Framers. If one, TPOS[0]/TNEG[0] are connected to RPOS[4]/RNEG[4], (0) and TPOS[4]/TNEG[4] are connected to RPOS[0]/RNEG[0]. This is used especially for 8.192 Mbit/s mode but may also be used in 2.048 Mbit/s mode. See Loopbacks section. RLBK67 Remote Loopback Framer 6 & 7. If one, TPOS[6]/TNEG[6] are connected to (0) RPOS[7]/RNEG[7], and TPOS[7]/TNEG[7] are connected to RPOS[6]/RNEG[6]. Used only in 2.048Mb/s mode. See Loopbacks section. RLBK45 Remote Loopback Framer 4 & 5. If one, TPOS[4]/TNEG[4] are connected to (0) RPOS[5]/RNEG[5], and TPOS[5]/TNEG[5] are connected to RPOS[4]/RNEG[4]. Used only in 2.048Mb/s mode. See Loopbacks section. RLBK23 Remote Loopback Framer 2 & 3. If one, TPOS[2]/TNEG[2] are connected to (0) RPOS[3]/RNEG[3], and TPOS[3]/TNEG[3] are connected to RPOS[2]/RNEG[2]. Used only in 2.048Mb/s mode. See Loopbacks section. RLBK01 Remote Loopback Framer 0 & 1. If one, TPOS[0]/TNEG[0] are connected to (0) RPOS[1]/RNEG[1], and TPOS[1]/TNEG[1] are connected to RPOS[0]/RNEG[0]. Used only in 2.048Mb/s mode. See Loopbacks section. # not used Table 123 - Framer Loopback Global Register(904) (T1)
9
8
7
6
5-0
Bit 15
Name
Functional Description
F3HVS Framer 3 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt HDLC (0) register(333) for framer are set. This bit can be masked and will remain low by the F3HM bit in address 902. F3EVS Framer 3 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(336) or Elastic store status for Framer 3 are set. This bit can be masked and will remain low by the F3EM bit in address 902. F3RVS Framer 3 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(335) for Framer 0 are set. This bit can be masked and will remain low by the F3RM bit in address 902. Table 124 - Interrupt Vector 1 Status Register (Address 910) (T1)
14
13
SEMICMF.019
143
MT9072
Bit 12 Name Functional Description
Data Sheet
F3SVS Framer 3 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(334) for Framer 3 are set. This bit can be masked and will remain low by the F3SM bit in address 902. F2HVS Framer 2 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt HDLC (0) register(233) or Elastic store status far Framer 2 are set. This bit can be masked and will remain low by the F2HM bit in address 902. F2EVS Framer 2 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elastic status register(236) or Elastic store status for Framer 2 are set. This bit can be masked and will remain low by the F2EM bit in address 902. F2RVS Framer 2 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(235) for Framer 2 are set. This bit can be masked and will remain low by the F2RM bit in address 902. F2SVS Framer 2 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Counter status register(234) for Framer 2 are set. This bit can be masked and will remain low by the F2SM bit in address 902. F1HVS Framer 1 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt HDLC (0) register(133) or Elastic store status for Framer 1 are set. This bit can be masked and will remain low by the F2HM bit in address 902. F1EVS Framer 1 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(136) or Elastic store status for Framer 1 are set. This bit can be masked and will remain low by the F1EM bit in address 902. F1RVS Framer 1 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(135) for Framer 1 are set. This bit can be masked and will remain low by theF1RM bit in address 902. F1SVS Framer 1 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(134) for Framer 3 are set. This bit can be masked and will remain low by the F1SM bit in address 902. F0HVS Framer 0 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt HDLC (0) register(033) or Elastic store status for Framer 0 are set. This bit can be masked and will remain low by the F0HM bit in address 902. F0EVS Framer 0 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(036) or Elastic store status for Framer 0 are set. This bit can be masked and will remain low by the F0EM bit in address 902. F0RVS Framer 0 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(035) for Framer 0 are set. This bit can be masked and will remain low by the F0RM bit in address 902. F0SVS Framer 0 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(034) for Framer 0 are set. This bit can be masked and will remain low by the F0SM bit in address 902. Table 124 - Interrupt Vector 1 Status Register (Address 910) (T1) (continued)
11
10
9
8
7
6
5
4
3
2
1
0
144
SEMICMF.019
Data Sheet
MT9072
Functional Description
Bit 15
Name
F7HVS Framer 3 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt HDLC (0) register(733) for Framer 7 are set. This bit can be masked and will remain low by the F7HM bit in address 903. F7EVS Framer 7 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(736) or Elastic store status for Framer 7 are set. This bit can be masked and will remain low by the F7EM bit in address 903. F7RVS Framer 7 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(735) for Framer 7 are set. This bit can be masked and will remain low by the F7RM bit in address 903 . F7SVS Framer 7 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt HDLC (0) register(734) for Framer 3 are set. This bit can be masked and will remain low by the F7SM bit in address 903. F6HVS Framer 6 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt HDLC (0) register(663) or Elastic store status for Framer 6 are set. This bit can be masked and will remain low by the F7HM bit in address 903. F6EVS Framer 6 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(636) or Elastic store status for Framer 5 are set. This bit can be masked and will remain low by the F5EM bit in address 903. F6RVS Framer 6 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(635) for Framer 6 are set. This bit can be masked and will remain low by the F6RM bit in address 903. F6SVS Framer 6 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Counter status register(634) for Framer 6 are set. This bit can be masked and will remain low by the F6SM bit in address 903. F5HVS Framer 3 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt HDLC (0) register(533) or Elastic store status for Framer 5 are set. This bit can be masked and will remain low by the F7HM bit in address 903. F5EVS Framer 5 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(536) or Elastic store status for Framer 5 are set. This bit can be masked and will remain low by the F5EM bit in address 903. F5RVS Framer 5 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(535) are Framer 5 are set. This bit can be masked and will remain low by theF1RM bit in address 903. F5SVS Framer 5 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(534) for Framer 5 are set. This bit can be masked and will remain low by the F1SM bit in address 903. F4HVS Framer 4 HDLC Vector Status. This bit if unmasked is set if any of the bits in the HDLC status (0) register(433)status for Framer 4 are set. This bit can be masked and will remain low by the F7HM bit in address 903. Table 125 - Interrupt Vector 2 Status Register (Address 911) (T1)
14
13
12
11
10
9
8
7
6
5
4
3
SEMICMF.019
145
MT9072
Bit 2 Name Functional Description
Data Sheet
F4EVS Framer 4 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(436) or Elastic store status for Framer 4 are set. This bit can be masked and will remain low by the F4EM bit in address 903. F4RVS Framer 4 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(435) for Framer 4 are set. This bit can be masked and will remain low by the F4RM bit in address 903. F4SVS Framer 4 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(434) Framer 4 are set. This bit can be masked and will remain low by the F4SM bit in address 903. Table 125 - Interrupt Vector 2 Status Register (Address 911) (T1)
1
0
Bit 15-3 2-0
Name ID15-3 ID2-0 (000)
Functional Description ID Number. Contains 0100000001011. These 3 bits make up a binary code which identify the revision of this device.
Table 126 - Identification Revision Code Data Register (Address 912) (T1)
Bit 15-1 0
Name # STIS (0) not used.
Functional Description
ST-BUS Analyser Interrupt Status. This bit is set if the ST-BUS Analyser is filled up.
Table 127 - ST-BUS Analyzer Vector Status Register (Address 913) (T1)
Bit 15-8 7-0
Name # not used.
Functional Description
STAD ST-BUS Analyser Data. This is the data for the ST-BUS analyser buffer. 920 is the first byte of the (7-0) data that is being "analyzed". The source of the data can be any ST-Bus stream from any Framer. (0) Table 128 - ST-BUS Analyser Data(Address 920-93F) (T1)
16.1.11 16.2 16.2.0.1
E1 Register Set Register Address (000 - FFF) Summaries Framer Address (000-FFF) Summary
146
SEMICMF.019
Data Sheet
Binary Address (A11-A0) 0000 xxxx xxxx 0001 xxxx xxxx 0010 xxxx xxxx 0011 xxxx xxxx 0100 xxxx xxxx 0101 xxxx xxxx 0110 xxxx xxxx 0111 xxxx xxxx 1000 xxxx xxxx 1001 xxxx xxxx Hex Address 0XX 1XX 2XX 3XX 4XX 5XX 6XX 7XX 8XX 900 901 902 903 904 905 910 911 912 913 920-93F 940 - FFF X indicates all (0 to F) hex possibilities Table 129 - Framer Addressing (000 - FFF) (E1) 0 1 2 3 4 5 6 7 Framer Accessed
MT9072
0 - 7, this performs an all framer write to register XX, except for the following addresses which are common to all 8 framers: Global Control 0(R/W) Global Control 1(R/W) Interrupt Vector 1 Mask Register (R/W) Interrupt Vector 2 Mask Register (R/W) Framer Loopback Register (R/W) ST-BUS Analyser Interrupt Mask Register Interrupt Vector1 Status Register(R) Interrupt Vector2 Status Register(R) ID Register (R) ST-BUS Analyser Interrupt Status Register ST-BUS Analyser Data not used
1010 0100 0000 1111 1111 1111 xxxx indicates all (0000 to 1111) binary possibilities
16.2.0.2
Register Group Address (Y00 - YFF) Summary
SEMICMF.019
147
MT9072
Binary Address (A10-A0) yyyy 0000 xxxx yyyy 0001 xxxx yyyy 0010 xxxx yyyy 0011 xxxx yyyy 0100 xxxx yyyy 0101 xxxx yyyy 0110 xxxx yyyy 0111 xxxxyyyy 1000 xxxx yyyy 1001xxxx yyyy 1010 xxxx Hex Address Y0X,YFX Y1X Y2X Y3X Y4X Y5X-Y6X Y7X-Y8X Y9X-YAX YB0-YBF YC0-YCF Register Group Accessed Master Control Master Status Latched Status Interrupt Status Interrupt Mask Control Transmit CAS Data Receive CAS Data Timeslot 0-31 Control Transmit National Bit Buffers Receive National Bit Buffers Processor Access R/W R R R R/W R/W R R/W R/W R
Data Sheet
ST-BUS Access ----------CSTi CSTo ---
yyyy indicates 9 binary (0000 to 1000) possibilities, 0000 to 0111 representing a read or write to1 of 8 framers, 1000 representing a write only to all framers, or a read/write to one of the common registers (904,912,910, 911,902,903) Y is the hex equivalent of yyyy xxxx indicates all (0000 to 1111) binary possibilities X is the hex equivalent of xxxx Table 130 - Register Group Address (Y00 - YFF) Summary (E1)
148
SEMICMF.019
Data Sheet
16.2.0.3 Global Control and Status Register (900-91F) Summary
Register Control Bits (B15 - B8 / B7 - B0)
MT9072
Binary Address Hex R/W (A11-A0) Address 1001 0000 0000 1001 0000 0001 1001 0000 0000 1001 0000 0011 1001 0000 1000 900 901 902 903 904
R/W Global Control0 R/W Global Control1 R/W Interrupt Vector Mask Register R/W Interrupt Vector MaskRegister
T1Eo, STBUS,#,#,#,#,#,#,#,#,#,CK1,#,#,#,RSTC CHANNUM(4:0),STBUFEN,FRNUM(2:0),CHUP,CONTSI N F3HM, F3NM, F3CM, F3SM, F2HM, F2NM, F2CM, F2SM, F1HM, F1NM, F1CM, F1SM, F0HM, F0NM, F0CM, F0SM F7HM,F7NM,F7CM,F7SM,F6HM,F6NM,F6CM,F6SM, F5HM,F5NM,F5CM,F5SM,F4HM,F4NM,F4CM,F4SM
R/W Framer SLBK8, SLBK67, SLBK45, SLBK23, SLBK01, Loopback Global RLBK8, RLBK67, RLBK45, RLBK23, RLBK01,#, #, #,#,# Register R/W not used not used
1001 0000 01011001 0000 1111 1001 0001 0000
906-90F
910
R
Interrupt Vector Status 0 Interrupt Vector Status1 Identification Code Status
F3HS,F3EVS, F3RVS, F3SVS,F2HS, F2EVS, F2RVS, F2SVS, F1HS,F1EVS, F1RVS, F1SVS,F0HS, F0EVS, F0RVS F0SVS F7HS,F7EVS, F7RVS, F7SVS,F6HS, F6EVS, F6RVS, F6SVS, F5HS,F5EVS, F5RVS, F5SVS,F4HS, F4EVS, F4RVS F4SVS #,#,#,#,#, #, #,ID7-0
1001 0001 0001
911
R
1001 0001 0010
912 913
R R
ST-Bus Analyser F0STS Interrupt Status Register not used not used
1001 0001 00111001 0001 1111
91491F 920-93F R
ST-Bus Analyser STAD(7:0) Data
# indicates unused bits in register that may be any value if read Table 131 - Register Group Address (Y00 - YFF) Summary (E1)
16.2.1
Register Address (Y00 - YFF) Summary
149
SEMICMF.019
MT9072
Tables 137 to 146 provide a summary of each of the framer registers for the MT9072.
Data Sheet
16.2.1.1
Master Control Registers Address (Y00-Y0F, YF0-YFF) Summary
Register Control Bits (B15 - B8 / B7 - B0) IMA, ASEL, ARAI, TALM, TAIS, TAIS0, TAI16, TE, TIU0, TIU1, CSYN, REFRM, AUTC, CRCM, AUTY, MFRF
Binary Address Hex (A10-A0) Address R/W yyyy 0000 0000 yyyy 0000 0001 yyyy 0000 0010 Y00 Y01 Y02
R/W Alarms and Framing Control
R/W Test, Loopback #, #, L32Z, ADSEQ, DLBK, RLBK, SLBK, PLBK, and Error Control E1, E2, BVE, CRCE, FASE, NFSE, LOSE, PERR R/W Interrupts and I/O Control R/W DL, CCS, CAS & Other Control R/W Signaling InterruptPeriod COD1, COD0, THDB3, T2OP, MFBE,Tx8KEN, SPND, INTA,CLKE, RHDB3, RxBFE, RxDO, RxCO, CSToE, DSToE, MFSEL #,#, #,#,#,#,#,#, #, ELAS, ACCLR, RxTRS, TxTRS, CSIG, CNCLR, RST #,#,#,#,#,#,#,#,#,#,#,#,#,#,#,SIP1-0
yyyy 0000 0011 yyyy 0000 0100 yyyy 0000 0101 yyyy 0000 0110 yyyy 0000 0111 yyyy 00001000 yyyy 00001001 yyyy 00001010
Y03 Y04 Y05 Y06 Y07 Y08 Y09 Y0A
R/W CAS Control and #, #, #, #, RFL, DBNCE, #, #, Data TMA1, TMA2, TMA3, TMA4, X1, Y, X2, X3 R/W HDLC &CCS ST-BUS Control R/W CCS to ST-BUS Map Control # ,#,#,#,HCH4:0,HPAYSEL,#,#,#,#,TS31E, TS16E, TS15E #, 31C4, 31C3, 31C2, 31C1, 31C0, 16C4, 16C3 16C2, 16C1, 16C0, 15C4, 15C3, 15C2, 15C1, 15C0
R/W DataLink Control Sa4SS1-0,Sa5SS1-0,Sa6SS1-0,Sa7SS1-0, Word Sa8SS1-0,#,#,#E4CK,DLCK R/W Receive Idle Code Word R/W Transmit Idle CodeWord not used not used #,#,#,#,ADREC,RXEN,TXEN,EOP,FA,MI,CYCLE,TCRCI, SEVEN,RXFRST,TXFRST #,#,#,#,#,#,#,#,#,#.HRST, RTLoop,CRCTST,FTST,ADTST,HLOOP #,ADRM26-20,A2EN,ADRM16-10,AEN #########RID(7:0) #########TID(7:0) -
yyyy 0000 1001- Y0B-Y0F yyyy 0000 1111 yyyy 1111 0000- YF0-YF1 yyyy 1111 0001 yyyy 1111 0010 yyyy 1111 0011 yyyy 1111 0100 YF2 YF3 YF4
R/W HDLC Control 0 R/W HDLC Test Control R/W Address Recognition
Table 132 - Master Control Register (R/W) Address (Y0X) Summary (E1)
150
SEMICMF.019
Data Sheet
Hex Binary Address R/W Address (A10-A0) yyyy 1111 0101 yyyy 1111 0110 YF5 YF6 Register Control Bits (B15 - B8 / B7 - B0) #,#,#,#,#,#,#,#,TXFIFO7-0 #,#,#,#,#,#,#,#,CNT7-0
MT9072
R/W TXFIFO7-0 R/W TX Byte Count
# indicates the unused bits in the register that may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y Table 132 - Master Control Register (R/W) Address (Y0X) Summary (E1)
16.2.1.2
Master Status Registers Address (Y10-Y1F) Summary
Register Synchronization & CRC-4 Remote Status CRC-4 Timers & CRC-4 Local Status Status Bits (B15 - B8 / B7 - B0) #, RSLP, RSLPD, BSYNC, MSYNC, CSYNC, RED, CEFS, #, RCRC0, RCRC1, RFAIL, REB1-2, RCRCR, CRCIW #, #,#, TWOSEC, T1, T2, T400, T8, #, #, #, CALN, CRCRF, CRCS1, CRCS2, #
Binary Address Hex (A10-A0) Address R/W yyyy 0001 0000 Y10 R
yyyy 0001 0001 yyyy 0001 0010 yyyy 0001 0011 yyyy 0001 0100 yyyy 0001 0101
Y11 Y12 Y13 Y14 Y15
R R R R
Alarms & MAS Status #, AISP, KLVE, LOSS, AIS16, AIS, RAI, AUXP, RMA1-4, X1, Y, X2, X3 NFAS & FAS Status Phase Indicator Status RIU1, RNFA, RAI, RNU4-8, RIU0, RFA2-8 #, #, #, #, PI11-8, PI7-0 PEC7-0,PCC7-0
R/W PRBS Error Counter & PRBS CRC-4 MF Counter
yyyy 0001 0110 yyyy 0001 0111 yyyy 0001 1000 yyyy 0001 1001 yyyy 0001 1010 yyyy 0001 1011 yyyy 0001 1100
Y16 Y17 Y18 Y19 Y1A Y1B Y1C
R/W Loss of Sync Counter SLC15-8,SLC7-0 with Auto Clear R/W E-bit Error Counter R/W BPV Error Counter EEC15-8,EEC7-0 VEC15-8, VEC7-0
R/W CRC-4 Error Counter CEC15-8, CEC7-0 R/W FAS Bit Error Counter BEC7-0 FEC7-0 FAS Error Counter R/W not used R/W TX Byte Counter Position and HDLC Test Status R/W HDLC Status #,#,#,#,RXclk,TXclk,Vcrc,Vaddr,TBP7:0
yyyy 0001 1101
Y1D
IDC,RQ9-8,TXSTAT1-0,RXSTA1-0
Table 133 - Master Status Register (R) Address (Y1X) Summary (E1)
SEMICMF.019
151
MT9072
Binary Address Hex (A10-A0) Address R/W yyyy 0001 1110 yyyy 0001 1111 Y1E Y1F Register CRC15-0 #,#,#,#,#,#,#,#,RXFIFO7-0 Status Bits (B15 - B8 / B7 - B0)
Data Sheet
R/W RX CRC R/W RX FIFO
# indicates the unused bits in the register that may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y Table 133 - Master Status Register (R) Address (Y1X) Summary (E1)
16.2.1.3
Binary Address (A10-A0)
Latched Status Registers Address (Y20-Y2F) Summary
Hex Address Y20-Y23 R/W Latched Status Register not used not used Status Bits (B15 - B8 / B7 - B0)
yyyy 0010 0000yyyy 0010 0011 yyyy 0010 0100
Y24
R
Sync (Sync, CRC-4 CASRL, RCRCRL, RSLPL, YL, AUXPL, RAIL, Remote, Alarms, MAS AISL, AIS16L, LOSSL, RCRC0L, RCRC1L, and Phase) CEFSL, RFAILL, CSYNCL, MSYNCL, BSYNCL Counter (Counter SLOL, 0, FEOL, FEIL, BEOL, BEIL, CEOL, CEIL, Indication and Counter VEOL, VEIL, EEOL, EEIL, PCO, 0, PEOL, PEIL Overflow) National (CAS, 0, Sa5VL, Sa6V3L, Sa6V2L, Sa6V1L, Sa6V0L, National, CRC-4 Local Sa6N8L, Sa6NL, SaNL, Sa5TL, SaTL, CASRL, and Timers) CALNL, T2L, T1L, ONESECL Performance Persistent Latch E-bit Error Count Latch #, #, #, #, #, #, #, #, #, #, #, #, RAISP, AISP, LOSSP, BSYNCP EEL15-8, EEL7-0
yyyy 0001 0101
Y25
R
yyyy 0001 0110
Y26
R
yyyy 0001 0111 yyyy 0001 1000 yyyy 0001 1001 yyyy 0001 1010 yyyy 0001 1011
Y27 Y28 Y29 Y2A Y2B
R R R R R
BPV Error Count Latch VEL15-8, VEL7-0 CRC-4 Error Count Latch CEL15-8, CEL7-0
FAS Bit Error Count BEL7-0 FEL7-0 Latch FAS Error Count Latch not used not used
yyyy 0010 1100yyyy 0010 1111
Y2C-Y2F
-
# indicates the unused bits in the register that may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y Table 134 - Latched Status Register (R) Address (Y2X) Summary (E1)
152
SEMICMF.019
Data Sheet
16.2.1.4
Binary Address (A10-A0) 1000 0011 0000 1000 0011 0001
MT9072
Interrupt Status Registers Address Summary(Y3X)
Hex Address R/W 910 911 Y33 R R R R Interrupt Status Register Vector 1 Vector 2 HDLC Interrupt Status Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Counter (Counter Indication and Counter Overflow) Status Bits (B15 - B8 / B7 - B0) F3HI, F3NI, F3CI, F3SI, F2HI, F2NI, F2CI, F2SI, F1HI, F1NI, F1CI, F1SI, F0HI, F0NI, F0CI, F0SI F7HI, F7NI, F7CI, F7SI, F6HI, F6NI, F6CI, F6SI, F5HI, F5NI, F5CI, F5SI, F4HI, F4NI, F4CI, F4SI GAI,EOPDI,TEOPI,EOPRI,TXFLI,FAI,TXUNDERI, RXFFI,RXOVFLI # RCRCRI, RSLPI, YI, AUXPI, RAII, AISI, AIS16I, LOSSI, RCRC0I, RCRC1I, CEFSI, RFAILI, CSYNCI, MSYNCI, BSYNCI SLOI, 0, FEOI, FEII, BEOI, BEII, CEOI, CEII, VEOI, VEII, EEOI, EEII, PCOI, 0, PEOI, PEII
yyyy 0011 0100 yyyy 0011 0101 yyyy 0011 0110 yyyy 0011 0111yyyy 0011 1111
Y34
Y35
R
Y36
R
National (CAS, National, Sa5VI, Sa6V3I, Sa6V2I, Sa6V1I, Sa6V0I, Sa6N8I, CRC-4 Local and Sa6NI, Timers) SaNI, Sa5TI, SaTI, #, CALNI, T2I, T1I, ONESECI not used not used
Y37-Y3F
-
# indicates the unused bits in the register that may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y Table 135 - Interrupt Status Register (R) Address Summary (E1)
SEMICMF.019
153
MT9072
16.2.1.5
Binary Address (A10-A0) yyyy 0100 0011 yyyy 0100 0100
Data Sheet
Interrupt Mask Registers Address Summary(Y4X)
Hex R/W Address Y43 Y44 R Interrupt Mask Register HDLC Interrupt Mask Control Bits (B15 - B8 / B7 - B0) GAIM,EOPDIM,TEOPIM,EOPRIM,TXFLIM,FAIM,TX UNDERIM,RXFFIM,RXOVFLIM CASRM, RCRCRM, RSLPM, YM, AUXPM, RAIM, AISM, AIS16M, LOSSM, RCRC0M, RCRC1M, CEFSM, RFAILM, CSYNCM, MSYNCM, BSYNCM SLOM, #M, FEOM, FEIM, BEOM, BEIM, CEOM, CEIM, VEOM, VEIM, EEOM, EEIM, PCOM, #, PEOM, PEIM Sa5VM, Sa6V3M, Sa6V2M, Sa6V1M, Sa6V0M, Sa6N8M, Sa6NM,SaNM, Sa5TM, SaTM, #, CALNM, T2M, T1M, ONESECM not used
R/W Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) R/W Counter (Counter Indication and Counter Overflow) R/W National (CAS, National, CRC-4 Local and Timers) not used
yyyy 0100 0101
Y45
yyyy 0100 0110
Y46
yyyy 0100 Y47-Y4F 0111yyyy 0100 1111
# indicates the unused bits in the register that may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y Table 136 - Interrupt Mask Register (R/W) Address Summary (E1)
16.2.1.6
Transmit CAS Data Registers Address (Y50-Y6F) Summary
Hex Address Y50 Y51 Y52 Y53 Y54 Y55 Y56 Y57 Y58 Y59 Y5A Y5B Y5C not used Channel 1 Transmit CAS Data Channel 2 Transmit CAS Data Channel 3 Transmit CAS Data Channel 4 Transmit CAS Data Channel 5 Transmit CAS Data Channel 6 Transmit CAS Data Channel 7 Transmit CAS Data Channel 8 Transmit CAS Data Channel 9 Transmit CAS Data Channel 10 Transmit CAS Data Channel 11 Transmit CAS Data Channel 12 Transmit CAS Data Register Data Bits (Upper bits B15 - B4 unused, B3 - B0 are shown) not used A1, B1, C1, D1 A2, B2, C2, D2 A3, B3, C3, D3 A4, B4, C4, D4 A5, B5, C5, D5 A6, B6, C6, D6 A7, B7, C7, D7 A8, B8, C8, D8 A9, B9, C9, D9 A10, B10, C10, D10 A11, B11, C11, D11 A12, B12, C12, D12
Binary Addres (A10-A0) yyyy 0101 0000 yyyy 0101 0001 yyyy 0101 0010 yyyy 0101 0011 yyyy 0101 0100 yyyy 0101 0101 yyyy 0101 0110 yyyy 0101 0111 yyyy 0101 1000 yyyy 0101 1001 yyyy 0101 1010 yyyy 0101 1011 yyyy 0101 1100
Table 137 - Transmit CAS Data Register (R/W) Address (Y5X,Y6X) Summary (E1)
154
SEMICMF.019
Data Sheet
Binary Addres (A10-A0) yyyy 0101 1101 yyyy 0101 1110 yyyy 0101 1111 yyyy 0110 0000 yyyy 0110 0001 yyyy 0110 0010 yyyy 0110 0011 yyyy 0110 0100 yyyy 0110 0101 yyyy 0110 0110 yyyy 0110 0111 yyyy 0110 1000 yyyy 0110 1001 yyyy 0110 1010 yyyy 0110 1011 yyyy 0110 1100 yyyy 0110 1101 yyyy 0110 1110 yyyy 0110 1111 Hex Address Y5D Y5E Y5F Y60 Y61 Y62 Y63 Y64 Y65 Y66 Y67 Y68 Y69 Y6A Y6B Y6C Y6D Y6E Y6F Register Channel 13 Transmit CAS Data Channel 14 Transmit CAS Data Channel 15 Transmit CAS Data not used Channel 16 Transmit CAS Data Channel 17 Transmit CAS Data Channel 18 Transmit CAS Data Channel 19 Transmit CAS Data Channel 20 Transmit CAS Data Channel 21 Transmit CAS Data Channel 22 Transmit CAS Data Channel 23 Transmit CAS Data Channel 24 Transmit CAS Data Channel 25 Transmit CAS Data Channel 26 Transmit CAS Data Channel 27 Transmit CAS Data Channel 28 Transmit CAS Data Channel 29 Transmit CAS Data Channel 30 Transmit CAS Data
MT9072
Data Bits (Upper bits B15 - B4 unused, B3 - B0 are shown) A13, B13, C13, D13 A14, B14, C14, D14 A15, B15, C15, D15 not used A16, B16, C16, D16 A17, B17, C17, D17 A18, B18, C18, D18 A19, B19, C19, D19 A20, B20, C20, D20 A21, B21, C21, D21 A22, B22, C22, D22 A23, B23, C23, D23 A24, B24, C24, D24 A25, B25, C25, D25 A26, B26, C26, D26 A27, B27, C27, D27 A28, B28, C28, D28 A29, B29, C29, D29 A30, B30, C30, D30
upper data bits (B15-4) are not used and may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y Note that this registers are useable if the corresponding MPST bits in the per timeslot control are set.
Table 137 - Transmit CAS Data Register (R/W) Address (Y5X,Y6X) Summary (E1) (continued)
16.2.1.7
Receive CAS Data Registers Address (Y70-Y8F) Summary
Hex Address Y70 Y71 Y72 Y73 Y74 Y75 Y76 not used Channel 1 Receive CAS Data Channel 2 Receive CAS Data Channel 3 Receive CAS Data Channel 4 Receive CAS Data Channel 5 Receive CAS Data Channel 6 Receive CAS Data Register Data Bits (Upper bits B15 - B4 unused, B3 - B0 are shown) not used A1, B1, C1, D1 A2, B2, C2, D2 A3, B3, C3, D3 A4, B4, C4, D4 A5, B5, C5, D5 A6, B6, C6, D6
Binary Address (A10-A0) yyyy 0111 0000 yyyy 0111 0001 yyyy 0111 0010 yyyy 0111 0011 yyyy 0111 0100 yyyy 0111 0101 yyyy 0111 0110
Table 138 - Receive CAS Data Register (R) Address (Y7X,Y8X) Summary (E1)
SEMICMF.019
155
MT9072
Binary Address (A10-A0) yyyy 0111 0111 yyyy 0111 1000 yyyy 0111 1001 yyyy 0111 1010 yyyy 0111 1011 yyyy 0111 1100 yyyy 0111 1101 yyyy 0111 1110 yyyy 0111 1111 yyyy 1000 0000 yyyy 1000 0001 yyyy 1000 0010 yyyy 1000 0011 yyyy 1000 0100 yyyy 1000 0101 yyyy 1000 0110 yyyy 1000 0111 yyyy 1000 1000 yyyy 1000 1001 yyyy 1000 1010 yyyy 1000 1011 yyyy 1000 1100 yyyy 1000 1101 yyyy 1000 1110 yyyy 1000 1111 Hex Address Y77 Y78 Y79 Y7A Y7B Y7C Y7D Y7E Y7F Y80 Y81 Y82 Y83 Y84 Y85 Y86 Y87 Y88 Y89 Y8A Y8B Y8C Y8D Y8E Y8F Register Channel 7 Receive CAS Data Channel 8 Receive CAS Data Channel 9 Receive CAS Data Channel 10 Receive CAS Data Channel 11 Receive CAS Data Channel 12 Receive CAS Data Channel 13 Receive CAS Data Channel 14 Receive CAS Data Channel 15 Receive CAS Data not used Channel 16 Receive CAS Data Channel 17 Receive CAS Data Channel 18 Receive CAS Data Channel 19 Receive CAS Data Channel 20 Receive CAS Data Channel 21 Receive CAS Data Channel 22 Receive CAS Data Channel 23 Receive CAS Data Channel 24 Receive CAS Data Channel 25 Receive CAS Data Channel 26 Receive CAS Data Channel 27 Receive CAS Data Channel 28 Receive CAS Data Channel 29 Receive CAS Data Channel 30 Receive CAS Data
Data Sheet
Data Bits (Upper bits B15 - B4 unused, B3 - B0 are shown) A7, B7, C7, D7 A8, B8, C8, D8 A9, B9, C9, D9 A10, B10, C10, D10 A11, B11, C11, D11 A12, B12, C12, D12 A13, B13, C13, D13 A14, B14, C14, D14 A15, B15, C15, D15 not used A16, B16, C16, D16 A17, B17, C17, D17 A18, B18, C18, D18 A19, B19, C19, D19 A20, B20, C20, D20 A21, B21, C21, D21 A22, B22, C22, D22 A23, B23, C23, D23 A24, B24, C24, D24 A25, B25, C25, D25 A26, B26, C26, D26 A27, B27, C27, D27 A28, B28, C28, D28 A29, B29, C29, D29 A30, B30, C30, D30
upper data bits (B15-4) are not used and may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y
Table 138 - Receive CAS Data Register (R) Address (Y7X,Y8X) Summary (E1)
16.2.1.8
Timeslot 0-31 Control Registers Address (Y90-YAF) Summary
156
SEMICMF.019
Data Sheet
Binary Address (A10-A0) yyyy 1001 0000 yyyy 1001 0001 yyyy 1001 0010 yyyy 1001 0011 yyyy 1001 0100 yyyy 1001 0101 yyyy 1001 0110 yyyy 1001 0111 yyyy 1001 1000 yyyy 1001 1001 yyyy 1001 1010 yyyy 1001 1011 yyyy 1001 1100 yyyy 1001 1101 yyyy 1001 1110 yyyy 1001 1111 yyyy 1010 0000 yyyy 1010 0001 yyyy 1010 0010 Hex Address Y90 Y91 Y92 Y93 Y94 Y95 Y96 Y97 Y98 Y99 Y9A Y9B Y9C Y9D Y9E Y9F YA0 YA1 YA2 Register Timeslot 0 Control Timeslot 1 Control Timeslot 2 Control Timeslot 3 Control Timeslot 4 Control Timeslot 5 Control Timeslot 6 Control Timeslot 7 Control Timeslot 8 Control Timeslot 9 Control Timeslot 10 Control Timeslot 11 Control Timeslot 12 Control Timeslot 13 Control Timeslot 14 Control Timeslot 15 Control Timeslot 16 Control Timeslot 17 Control Timeslot 18 Control
MT9072
Control Bits (Upper byte B15 - B8 unused, B8 - B0 are shown) Set to 0 RADI1,MPDR1,MPDR1,CASS1, TADI1, RTSL1, LTSL1, TTST1, RRST1, MPDT1, # RADI2,MPDR2,MPDR2,CASS2, TADI2, RTSL2, LTSL2, TTST2, RRST2, MPDT2, # RADI3,MPDR3,MPDR3,CASS3,T ADI3, RTSL3, LTSL3, TTST3, RRST3, MPDT3, # RADI4,MPDR4,MPDR4,CASS4, TADI4, RTSL4, LTSL4, TTST4, RRST4, MPDT4, # RADI5,MPDR5,MPDR5,CASS5, TADI5, RTSL5, LTSL5, TTST5, RRST5, MPDT5, # RADI6,MPDR6,MPDR6,CASS6, TADI6, RTSL6, LTSL6, TTST6, RRST6, MPDT6, # RADI7,MPDR7,MPDR7,CASS7, TADI7, RTSL7, LTSL7, TTST7, RRST7, MPDT7, # RADI8,MPDR8,MPDR8,CASS8, TADI8, RTSL8, LTSL8, TTST8, RRST8, MPDT8, # RADI9,MPDR9,MPDR9,CASS9, TADI9, RTSL9, LTSL9, TTST9, RRST9, MPDT9, # RADI10,MPDR10,MPDR10,CASS10,T ADI10, RTSL10, LTSL10, TTST10, RRST10, MPDT10, # RADI11,MPDR11,MPDR11,CASS11,T ADI11, RTSL11, LTSL11, TTST11, RRST11, MPDT11, # RADI12,MPDR12,MPDR12,CASS12, TADI12, RTSL12, LTSL12, TTST12, RRST12, MPDT12, # RADI13,MPDR13,MPDR13,CASS13, TADI13, RTSL13, LTSL13, TTST13, RRST13, MPDT13, # RADI14,MPDR14,MPDR14,CASS14, TADI14, RTSL14, LTSL14, TTST14, RRST14, MPDT14, # RADI15,MPDR15,MPDR15,CASS15, TADI15, RTSL15, LTSL15, TTST15, RRST15, MPDT15, # RADI16,MPDR16,MPDR16,CASS16, TADI16, RTSL16, LTSL16, TTST16, RRST16, MPDT16, # RADI17,MPDR17,MPDR17,CASS17, TADI17, RTSL17, LTSL17, TTST17, RRST17, MPDT17, # RADI18,MPDR18,MPDR18,CASS18, TADI18, RTSL18, LTSL18, TTST18, RRST18, MPDT18, #
Table 139 - Timeslot 0-31 Control Register (R/W) Address (Y9X, YAX) Summary (E1)
SEMICMF.019
157
MT9072
Binary Address (A10-A0) yyyy 1010 0011 yyyy 1010 0100 yyyy 1010 0101 yyyy 1010 0110 yyyy 1010 0111 yyyy 1010 1000 yyyy 1010 1001 yyyy 1010 1010 yyyy 1010 1011 yyyy 1010 1100 yyyy 1010 1101 yyyy 1010 1110 yyyy 1010 1111 Hex Address YA3 YA4 YA5 YA6 YA7 YA8 YA9 YAA YAB YAC YAD YAE YAF Register Timeslot 19 Control Timeslot 20 Control Timeslot 21 Control Timeslot 22 Control Timeslot 23 Control Timeslot 24 Control Timeslot 25 Control Timeslot 26 Control Timeslot 27 Control Timeslot 28 Control Timeslot 29 Control Timeslot 30 Control Timeslot 31 Control
Data Sheet
Control Bits (Upper byte B15 - B8 unused, B8 - B0 are shown) RADI19,MPDR19,MPDR19,CASS19, TADI19, RTSL19, LTSL19, TTST19, RRST19, MPDT19, # RADI20,MPDR20,MPDR20,CASS20, TADI20, RTSL20, LTSL20, TTST20, RRST20, MPDT20, # RADI21,MPDR21,MPDR21,CASS21, TADI21, RTSL21, LTSL21, TTST21, RRST21, MPDT21, # RADI22,MPDR22,MPST22,CASS22, TADI22, RTSL22, LTSL22, TTST22, RRST22, MPDT22, # RADI23,MPDT23,MPDR23,CASS23, TADI23, RTSL23, LTSL23, TTST23, RRST23, MPDT23, # RADI24,MPDT24,MPDR24,CASS24, TADI24, RTSL24, LTSL24, TTST24, RRST24, MPDT24, # RADI25,MPDT25,MPDR25,CASS25, TADI25, RTSL25, LTSL25, TTST25, RRST25, MPDT25, # RADI26,MPDT26,MPDR26,CASS26, TADI26, RTSL26, LTSL26, TTST26, RRST26, MPDT26, # RADI27,MPDT27,MPDR27,CASS27, TADI27, RTSL27, LTSL27, TTST27, RRST27, MPDT27, # RADI28,MPDT28,MPDR28,CASS28, TADI28, RTSL28, LTSL28, TTST28, RRST28, MPDT28, # RADI29,MPDT29,MPDR29,CASS29, TADI29, RTSL29, LTSL29, TTST29, RRST29, MPDT29, # RADI30,MPDT30,MPDR30,CASS30, TADI30, RTSL30, LTSL30, TTST30, RRST30, MPDT30, # RADI31,MPDT31,MPDR31,CASS31,TADI31, RTSL31, LTSL31, TTST31, RRST31, MPDT31, #
upper data byte (B15-8) is not used and may be any value if read # indicates the unused bits in the register that may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y Table 139 - Timeslot 0-31 Control Register (R/W) Address (Y9X, YAX) Summary (E1)
158
SEMICMF.019
Data Sheet
16.2.1.9
MT9072
Data Bits (Upper byte B15 - B8 unused, B7 - B0 are shown) TN0F1, TN0F3, TN0F5, TN0F7, TN0F9, TN0F11, TN0F13, TN0F15 TN1F1, TN1F3, TN1F5, TN1F7, TN1F9, TN1F11, TN1F13, TN1F15 TN2F1, TN2F3, TN2F5, TN2F7, TN2F9, TN2F11, TN2F13, TN2F15 TN3F1, TN3F3, TN3F5, TN3F7, TN3F9, TN3F11, TN3F13, TN3F15 TN4F1, TN4F3, TN4F5, TN4F7, TN4F9, TN4F11, TN4F13, TN4F15 not used
Transmit National Bit Data Register(R/W) Address(YB0 to YB4) Summary
Register Transmit National Bits TN0 (Sa4) Transmit National Bits TN1 (Sa5) Transmit National Bits TN2 (Sa6) Transmit National Bits TN3 (Sa7) Transmit National Bits TN4 (Sa8) not used
Binary Address Hex (A10-A0) Address yyyy 1111 1000 yyyy 1111 1001 yyyy 1111 1010 yyyy 1111 1011 yyyy 1111 0100 yyyy 1011 0101yyyy 1011 1111 YB0 YB1 YB2 YB3 YB4 YB5YBF
upper data byte (B15-8) is not used and may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y Table 140 - Transmit National Bits Data Registers (R/W) Address (YFX) Summary (E1)
16.2.1.10
Receive National Bit Data Register(R/W) Address(YC0 to YC4) Summary
Register Receive National Bits RN0 (Sa4) Receive National Bits RN1 (Sa5) Receive National Bits RN2 (Sa6) Receive National Bits RN3 (Sa7) Receive National Bits RN4 (Sa8) not used Data Bits (Upper byte B15 - B8 unused, B7 - B0 are shown) RN0F1, RN0F3, RN0F5, RN0F7, RN0F9, RN0F11, RN0F13, RN0F15 RN1F1, RN1F3, RN1F5, RN1F7, RN1F9, RN1F11, RN1F13, RN1F15 RN2F1, RN2F3, RN2F5, RN2F7, RN2F9, RN2F11, RN2F13, RN2F15 RN3F1, RN3F3, RN3F5, RN3F7, RN3F9, RN3F11, RN3F13, RN3F15 RN4F1, RN4F3, RN4F5, RN4F7, RN4F9, RN4F11, RN4F13, RN4F15 not used
Hex Binary Address Address (A10-A0) yyyy 1111 1000 yyyy 1111 1001 yyyy 1111 1010 yyyy 1111 1011 yyyy 1111 0100 yyyy 1011 0101yyyy 1011 1111 YC0 YC1 YC2 YC3 YC4 YC5YCF
upper data byte (B15-8) is not used and may be any value if read see the Register Group Address Summary for an explanation of yyyy and Y Table 141 - Transmit National Bits Data Registers (R/W) Address (YFX) Summary (E1)
SEMICMF.019
159
MT9072
16.2.2 Master Control Registers (Y00 - Y09) Bit Functions
Data Sheet
Tables 147 to 157 describe the bit functions of each of the Master Control Registers in the MT9072 in E1 Mode. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11A8). In addition, a simultaneous write to all 8 framers is possible by setting the MSB address to Y=8 (1000). A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a reset (RESET, RSTC or RST). The (#) indicates that a (0) or (1) is possible.
Bit 15
Name IMA
Functional Description Inverse Mux for ATM Mode. Setting this bit high the I/O ports to allow for easy connection to one of the Zarlink IMA devices such as the MT90220. DSTi becomes a serial 2.048 data stream. C4b becomes a 4.096 MHz clock that clocks DSTi as the St-Bus. RXFPB becomes a framing pulse that flags the E1 stream coming from the pin DSTo. The data from DSTo is clocked out on RXDLC. Set this pin low for all other applications. Note that signalling operations CSTi/CSTo do not function with the IMA Mode. The global control register 900 bit CK1 is ignored for this framer. 8.192 Mbit/s backplane mode is not supported if IMA mode is selected on any one framer. AIS Select. This bit selects the criteria on which the detection of a valid alarm indication signal (AIS=1 of register address Y11) is based. If zero, the criteria is fewer than three zeros in a two frame period (512 bits). If one, the criteria is fewer than three zeros in each of two consecutive double-frame periods (512 bits per double-frame). Automatic Remote Alarm Indication (RAI) Operation. This bit determines the source for the Remote Alarm Indication bit (the A bit) of the transmit PCM30 signal (time-slot 0 bit 3 of NFAS frames). If zero, the source for the A bit is the RAI bit of the Timer and Alarm Status Register (address Y11), and consequently, will change automatically. That is, A=0 when basic synchronization has been acquired (RAI=0), and A=1 when basic synchronization has not been acquired (RAI=1). If the ARAI bit is set to one, the A bit is controlled through the TALM control bit (register address Y00). Transmit Remote Alarm. This bit is the source for the Remote Alarm Indication bit (the A bit) of the transmit PCM30 signal (timeslot 0 bit 3 of NFAS frames) when the ARAI control bit (register address Y00) is set to one. The TALM bit is used to signal an alarm to the remote end of the PCM30 link (one - alarm, zero - normal). Transmit Alarm Indication Signal. If one, an all ones signal is transmitted in all timeslots except zero and 16. If zero, timeslots function normally. Transmit AIS Timeslot Zero. If one, an all ones signal is transmitted in timeslot zero. If zero, timeslot zero functions normally. Transmit AIS Timeslot 16. If one, an all ones signal is transmitted in timeslot 16. If zero, timeslot functions normally. Transmit E bits. If zero, and CRC-4 synchronization is achieved, the PCM30 link E-bits transmit the received CRC-4 comparison results to the distant end of the link, as per G.703. If zero, and CRC-4 synchronization is lost, the E-bits transmit zero. If one, and CRC-4 synchronization is lost the transmit E-bits will be one. Table 142 - Alarm and Framing Control Register Y00 (R/W Address Y00) (E1)
14
ASEL (0)
13
ARAI (0)
12
TALM (0)
11 10 9 8
TAIS (0) TAIS0 (0) TAI16 (0) TE (0)
160
SEMICMF.019
Data Sheet
Bit 7 Name TIU0 (0) Functional Description
MT9072
Transmit International Use Zero. This bit is transmitted on the PCM30 2048kb/s link in bit position one of time-slot 0 of all the frame-alignment signal (FAS) frames when CRC-4 operation is disabled (CSYN=1 of register address Y00). The TIU0 bit is reserved for international use and should normally be kept at one. If CRC-4 operation is enabled (CSYN=0), this bit is ignored. Transmit International Use One. This bit is transmitted on the PCM 30 2048kb/s link in bit position one of timeslot 0 of all the Non-Frame Alignment Signal (NFAS) frames when CRC-4 operation is disabled (CSYN=1 of register address Y00). The TIU1 bit is reserved for international use and should normally be kept at one. If CRC-4 operation is enabled (CSYN=0), this bit is ignored. CRC-4 Synchronization. The CSYN bit in combination with AUTC determines the enabling or disabling of the CRC functions for timeslot 0. If one and AUTC (register address Y00) is one the first bits of time-slot 0 for the transmitter are used as international use bits and are programmed by the TIU0 and TIU1bits (register address Y00). If AUTC is a zero, the CRC-4 calculated bits are inserted in the FAS frames as shown in Table 12. Also if AUTC is a one, the CSYN has to be low for the CRC-4 bits to be inserted in the FAS frames. The transmit transparent bit overides the function of this bit for the transmitter. On the receiver side, if AUTC is 1 and CSYN is 0 then more than 914 CRC errors in 1 second will cause a resynchronization and search for a basic frame synchronization. If AUTC is a 1 and CSYN is 1 than CRC errors are ignored. If AUTC is a zero than more than 914 CRC errors in 1 second will result in basic frame reframe.
6
TIU1 (1)
5
CSYN (0)
4
REFRM Reframe. A one-to-zero transition of this bit results in the execution of the reframing function (the (0) search for a new basic frame position). The basic frame alignment pattern is x0011011 in timeslot 0 of alternate frames. AUTC (0) Automatic CRC-interworking. If zero, automatic CRC-interworking is activated. If one, it is deactivated. See Framing Algorithm section, Table 13 for details.
3 2
CRCM CRC-4 Modification. If one, the transmit CRC-4 remainder is modified when the device is in (0) transmit transparent mode (TxTRS=1 of register address Y03) in accordance with the local datalink. The received CRC-4 remainder from the originating node is modified to reflect only the changes in the local transmit DataLink. If zero, time-slot 0 data from DSTi will not be modified in transmit transparent mode. This feature can used for intermediate nodes where 2 end nodes are commmunicating for framing/signalling and 2 intermediate nodes are sending datalink information in accordance with appendix C of G.706. AUTY (0) Automatic Y-Bit Operation. This bit determines the source for the Remote Multiframe Alarm Indication bit (the Y bit) of the transmit PCM30 signal (time-slot 16 bit 6 of every frame 0 of the CAS multiframe). If zero, the source for the Y bit is the Y bit of the Receive Alignment Signals Status Register (address Y12), and consequently, will change automatically. That is, Y=0 when multiframe alignment has been acquired (Y=0 of status register), and Y=1 when multiframe alignment has not been acquired (Y=1 of status register). If the AUTY bit is set to one, the Y bit is controlled through the Y bit of the CAS Control and Data Register (address Y05). Multiframe Reframe. If one, for at least one frame, and then cleared, the selected framer (Y) will initiate a search for a new signalling multiframe position. Reframing function is activated on the one-to-zero transition of the MFRF bit. The signalling multiframe algorithm will align to the first multiframe alignment signal pattern (MFAS = 0000) it receives in the most significant nibble of channel 16 (status register address Y10 bit MSYNC is zero). Signalling multiframing will be lost when two consecutive multiframes are received in error. Table 142 - Alarm and Framing Control Register Y00 (R/W Address Y00) (E1)
1
0
MFRF (0)
SEMICMF.019
161
MT9072
Bit 15-14 13 12 Name # L32Z (0) ADSEQ (0) not used. Functional Description
Data Sheet
Digital Loss of Signal Selection. If one, the threshold for digital loss of signal is 32 successive zeros. If zero, the threshold is set to 192 successive zeros. Digital Milliwatt or Digital Test Sequence. If one, the A-law digital milliwatt analog test sequence will be selected by the Per Timeslot Control bits TTSTn and RTSTn (register address Y90 to YAF). If zero, the PRBS 215-1 bit error rate test sequence will be selected by the Per Timeslot Control bits TTSTn and RTSTn. The PRBS generator is reset whenever this bit is set to 1. Digital Loopback. If one, all timeslots of DSTi are connected to DSTo on the PCM30 side of the selected framer (Y). If zero, this feature is disabled. See Loopbacks section. Remote Loopback. If one, all timeslots received on RPOS/RNEG are connected to TPOS/TNEG on the PCM30 side of the selected framer (Y). If zero, this feature is disabled. See Loopbacks section. ST-BUS Loopback. If one, all timeslots of DSTi are connected to DSTo on the ST-BUS side of the selected framer (Y). If zero, this feature is disabled. See Loopbacks section. Payload Loopback. If one, all timeslots received on RPOS/RNEG are connected to TPOS/TNEG on the ST-BUS side(DSTo to DSTi) of the selected framer (Y) (this excludes time-slot 0). Hence the data passes through the receiver and output to DSTo. This DSTo data is looped back to DSTi which is transmitted to TPOS/TNEG by the transmitter. If zero, this feature is disabled. See Loopbacks section. E1 Error Insertion. A zero-to-one transition of this bit inserts a single E1 error into the transmit PCM30 data (bit position 1 of frame 13 of the CRC-4 Multiframe). A one, zero or oneto-zero transition has no function. E2 Error Insertion. A zero-to-one transition of this bit inserts a single E2 error into the transmit PCM30 data (bit position 1 of frame 15 of the CRC-4 Multiframe). A one, zero or oneto-zero transition has no function. Bipolar Violation Error Insertion. A zero-to-one transition of this bit inserts a single bipolar violation error into the transmit PCM30 data. A one, zero or one-to-zero transition has no function. CRC-4 Error Insertion. A zero-to-one transition of this bit inserts a single CRC-4 error into the transmit PCM30 data. A one, zero or one-to-zero transition has no function. Frame Alignment Signal Error Insertion. A zero-to-one transition of this bit inserts a single error into the timeslot zero frame alignment signal of the transmit PCM30 data. A one, zero or one-to-zero transition has no function. Non-frame Alignment Signal Error Insertion. A zero-to-one transition of this bit inserts a single error into bit two of the timeslot zero non-frame alignment signal of the transmit PCM30 data. A one, zero or one-to-zero transition has no function. Loss of Signal Error Insertion. If one, the selected framer (Y) transmits an all zeros signal (no pulses) in every PCM30 timeslot, and, the HDB3 control bit (reg address Y02) has no effect. If zero, data is transmitted normally. Payload Error Insertion. A zero-to-one transition of this bit inserts a single error in the transmit payload. A one, zero or one-to-zero transition has no function.
11 10
DLBK (0) RLBK (0) SLBK (0) PLBK (0)
9 8
7
E1 (0) E2 (0) BVE (0) CRCE (0) FASE (0) NFSE (0) LOSE (0) PERR (0)
6
5
4 3
2
1
0
Table 143 - Test, Error and Loopback Control Register (R/W Address Y01) (E1)
162
SEMICMF.019
Data Sheet
MT9072
Bit 15 14
Name COD1 COD0 (1 0)
Functional Description Line Coding. These two coding select bits determine the transmit and receive coding options as follows. See Figures 64 to 67. COD1 COD0 Function 00 RZ (Return to Zero, Dual Rail) 01 NRZ (Non-return to Zero, Single Rail) 10 NRZB (Non-return to Zero, Dual Rail) 11 No function
13
RHDB3 RHDB3 (High Density Bipolar 3) encoding. If zero, HDB3 decoding is enabled in the receive (0) direction. If one, AMI (Alternate Mark Inversion) signal without HDB3 decoding is enabled in the transmit direction. T2OP (0) T2o Polarity. If one, the TxCL pin will output a 2.048MHz clock whose rising edge is in the center of the transmitted PCM30 bit cell at the TPOS and TNEG transmit pins. This clock is equivalent to the internal ST-BUS C2 clock. If zero, the TxCL pin will output a 2.048MHz clock whose falling edge is in the center of the transmitted PCM30 bit cell at the TPOS and TNEG transmit pins. This clock is equivalent to the internal ST-BUS C2 clock. Transmit Multiframe Boundary Enable. If one, the TxMF pin will be enabled. If zero, the TxMF pin will be disabled. See the TxMF pin description.
12
11
MFBE (0)
10 Tx8KEN Transmit 8 KHz Enable. If one, the pin RxMF transmits a positive 8 KHz frame pulse synchronous with the serial data stream transmit on TPOS/TNEG. If zero, the pin RxMF transmits a negative frame pulse synchronous with the multiframe boundary of data coming out of DSTo. 9 SPND (0) INTA (0) Suspend Interrupts. If zero, the selected framers contribution to the IRQ pin output will be a high impedance state, but all interrupt status registers will continue to be updated. If one, the selected framers contribution to the IRQ output will be normal operation. Interrupt Acknowledge. If zero, all interrupt and latched status registers are cleared and the selected framers contribution to the IRQ pin output will be a high impedance state. If one, all interrupt status registers and the selected framers contribution to the IRQ output will be normal operation. Clock Edge. If one then the NRZ data (RPOS/RNEG) is sampled on the rising edge of EXCLi and transmitted on the falling edge of EXCLi. This selection is only applicable in NRZ mode.
8
7 6
CLKE (0)
THDB3 THDB3 (High Density Bipolar 3) Encoding. If zero, HDB3 encoding is enabled in the transmit (0) direction. If one, AMI (Alternate Mark Inversion) signal without HDB3 encoding is enabled in the transmit direction. RxBFE Receive Basic Frame Enable. If one, the RxBF pin operates normally. If zero, the RxBF pin is (0) low. RxDO (0) RxCO (0) Receive DSTo All Ones. If one, the DSTo pin operates normally. If zero, all timeslots (0-31) of DSTo are set to one. Receive CSTo All Ones. If one, the CSTo pin operates normally. If zero, all timeslots (0-31) of CSTo are set to one.
5 4 3 2
CSToE Output CSTo Enable. If one, the CSTo pin operates normally. If zero, CSTo will be at high (0) impedance. In 8.192 Mbit/s mode all CSToE for all framers have to be 0 to obtain high impedance. Table 144 - Interrupts and I/O Control Register (R/W Address Y02) (E1)
SEMICMF.019
163
MT9072
Bit 1 0 Name Functional Description
Data Sheet
DSToE Output DSTo Enable. If one, the DSTo pin operates normally. If zero, DSTo will be at high (0) impedance. MFSEL Multiframe Select. This bit determines which receive multiframe signal (CRC-4 or signaling) the (0) frame pulse at the RxMF pin is aligned with. If zero, the frame pulse at the RxMF pin is aligned with the receive channel associated signaling (CAS) multiframe; if one, the receive CRC-4 multiframe. See Figures 55 & 58. Table 144 - Interrupts and I/O Control Register (R/W Address Y02) (E1)
Bit 15-7 6
Name # ELAS (0) not used.
Functional Description
Elastic Buffer Enable. When this bit is set to one, the data at DSTo is a 2.048Mb/s serial output stream which contains all 32 timeslots of the received PCM30 link data after HDB3 decoding. This data does not pass through the elastic buffer and is clocked out with the falling edge of EXCLi. The data at the DSTo pin is identical to the data at the RXDL pin. When this bit is set to zero, the elastic buffer is enabled, and DSTo operates synchronously with the clock at the CKi pin. Note that only RXDLC or the EXCL can be used to clock DSTo data and DSTo data has no relationship to CKi when ELAS is1.
5
ACCLR Automatic Counter Clear. When this bit is set to one, all non-latched status counters (address (0) Y15 to Y1A) are cleared automatically by the one second timer bit ONESEC (address Y11) immediately following the counter latch operation (address Y25 to Y2B). If zero, all non-latched status counters operate normally. RxTRS Receive Transparent Mode. If one, the framing function is disabled on the receive side. Data (0) coming from the receive line passes through the slip buffer and drives DSTo with an arbitrary alignment. When zero, the receive framing function operates normally. TxTRS Transmit Transparent Mode. If one, the MT9072 is in transmit transparent mode where no (0) framing or signaling is imposed on data transmitted from DSTi onto the PCM30 line. In other words, timeslot 0 and timeslot 16 data on the transmit PCM30 link is sourced from the DSTi input. If zero, the MT9072 is in termination mode. CSIG (0) CCS and CAS signaling. If one, the MT9072 is in Common Channel signaling (CCS) mode. If zero, the MT9072 is in Channel Associated signaling (CAS) mode.
4
3
2 1 0
CNCLR Counter Clear. When this bit is changed from zero to one, all non-latched status counters (0) (address Y15 to Y1A) are cleared. If zero, all non-latched status counters operate normally. RST (0) Reset. When this bit is changed from zero to one, the selected framer (Y) will reset to its default mode. See the Reset Operation section for the default settings.
Table 145 - DL, CCS, CAS and Other Control Register (R/W Address Y03) (E1)
164
SEMICMF.019
Data Sheet
MT9072
Functional Description
Bit 15-2 1-0
Name # not used.
SIP1-0 Signaling Interrupt Period. These 2 bits determine the signaling Interrupt period due to the Receive signaling changes. This 2 bits determine the duration of the signaling interrupt bit CASRI(Y36). 00 2 msec Period 01 8 msec Period 10 16 msec Period Table 146 - Signaling Period Interrupt Word (R/W Address Y04) (E1)
Bit 15-12 11 10
Name # RFL (0) not used.
Functional Description
Receive Signaling Freeze due to Loss. If one, the receive signaling is frozen if a receive loss of signal is detected. The freeze is cleared upon clearance of Loss.
DBNCE Debounce Select. This bit selects the receive CAS debounce period. If one, 14 ms of (0) debounce is used. There may be as much as 2 ms added to this duration because the state change of the signaling equipment is not synchronous with the PCM30 signaling multiframe. If zero, no debounce is used. (00) TMA1 TMA2 TMA3 TMA4 (0000) X1 (1) Y (1) not used. Transmit Multiframe Alignment Bits One to Four. These bits are transmitted on the PCM30 link, in the Multiframe Alignment Signal (MFAS) positions (one to four of timeslot 16) of frame zero of every Channel Associated signaling (CAS) multiframe. These bits are used by the far end to identify specific frames of a CAS multiframe. TMA1-4 = 0000 for normal operation. Transmit Non-Multiframe Alignment Signal (NMAS) Spare Bit. This bit is transmitted on the PCM30 link in bit position five of timeslot 16 of frame zero of every signaling multiframe. X1 is normally set to one. Transmit Remote Multiframe Alarm Signal. This bit is transmitted on the PCM30 link in bit position six of timeslot 16 of frame zero of every signaling multiframe when control bit AUTY (register address Y00) is set to one. The Y bit is used to indicate the loss of multiframe alignment to the remote end of the link. If one, loss of multiframe alignment; if zero, multiframe alignment acquired. Transmit Non-Multiframe Alignment Signal (NMAS) Spare Bits. These bits are transmitted on the PCM30 link in bit positions seven and eight respectively, of timeslot 16 of frame zero of every signaling multiframe. X2 and X3 are normally set to one. Table 147 - CAS Control and Data Register (R/W Address Y05) (E1)
9,8 7 6 5 4 3
2
1 0
X2 X3 (11)
SEMICMF.019
165
MT9072
Bit 15-12 11-7 Name # HCH4-0 (0) not used. Functional Description
Data Sheet
HDLC Channel 4-0. This 5 bit number specifies the channel time HDLC will be attached to if enabled. Channel 1 is the first channel in the frame. Channel 31 is the last channel available in a E1 frame. If enabled in a channel, HDLC data will be substituted for data from DSTi on the transmit side. Receive data is extracted from the incoming line data before the elastic buffer and decoded by the HDLC receiver. This bits are relevant if HPAYSEL is set.
6 5-3 2
HPAYSEL HDLC Payload Select. Set this bit to 1 to attach HDLC0 to a payload timeslot, if zero it is (0) attached to the Facility data link in Timeslot 0 in accordance with selections in Y08. # TS31E (0) not used Time Slot 31 CST Enable. If one, the transmit PCM30 link timeslot 31 data will be sourced from a CSTi timeslot as selected by control bits 31C4 to 31C0 of register address Y07. And, the receive PCM30 link timeslot 31 data will be sourced to both DSTo timeslot 31 and to the above selected CSTo timeslot. This feature is used to link PCM30 CCS data to an external HDLC device through the CSTo and CSTi pins. If zero, the transmit PCM30 link timeslot 31 data will be sourced from DSTi timeslot 31. And, the receive PCM30 link timeslot 31 data will be sourced to DSTo timeslot 31 only. CCS (CSIG =1 of register address Y03) must be selected for these operations to be valid.
1
TS16E (0)
Time Slot 16 CST Enable. If one, the transmit PCM30 link timeslot 16 data will be sourced from a CSTi timeslot as selected by control bits 16C4 to 16C0 of register address Y07. And, the receive PCM30 link timeslot 16 data will be sourced to both DSTo timeslot 16 and to the above selected CSTo timeslot. This feature is used to link PCM30 CCS data to an external HDLC device through the CSTo and CSTi pins. If zero, the transmit PCM30 link timeslot 16 data will be sourced from DSTi timeslot 16. And, the receive PCM30 link timeslot 16 data will be sourced to DSTo timeslot 16 only. CCS (CSIG=1 of register address Y03) must be selected for these operations to be valid.
0
TS15E (0)
Time Slot 15 CST Enable. If one, the transmit PCM30 link timeslot 15 data will be sourced from a CSTi timeslot as selected by control bits 15C4 to 15C0 of register address Y07. And, the receive PCM30 link timeslot 15 data will be sourced to both DSTo timeslot 15 and to the above selected CSTo timeslot. This feature is used to link PCM30 CCS data to an external HDLC device through the CSTo and CSTi pins. If zero, the transmit PCM30 link timeslot 15 data will be sourced from DSTi timeslot 15. And, the receive PCM30 link timeslot 15 data will be sourced to DSTo timeslot 15 only. CCS (CSIG=1 of register address Y03) must be selected for these operations to be valid.
Table 148 - HDLC & CCS ST-BUS Control Register (R/W Address Y06) (E1)
166
SEMICMF.019
Data Sheet
Bit 15 14 13 12 11 10 Name # 31C4 31C3 31C2 31C1 31C0 (11111) not used. Functional Description
MT9072
Timeslot 31 CST Map Bits. The selection of these bits results in a mapping of the transmit PCM30 timeslot 31, from a specific CSTi timeslot; and similarly, maps receive PCM30 timeslot 31, to a specific CSTo timeslot. PCM30 timeslot 31 data is mapped to/from CST channel n (n=0 to 31), where n is the BCD (Binary Coded Decimal) equivalent of 31C4 to 31C0 with 31C4 being the most significant bit. 31C4 0 0 0 1 Bit Settings 31C3 31C2 31C1 0 0 0 0 0 0 0 0 1 etc. 1 1 1 31C0 0 1 0 1 Selected CST Timeslot 0 1 2 31
CCS (CSIG=1 of register address Y03) and CST (TS31E=1 of register address Y06) must be selected for these operations to be valid. 9 8 7 6 5 16C4 16C3 16C2 16C1 16C0 (10000) Timeslot 16 CST Map Bits. The selection of these bits results in a mapping of the transmit PCM30 timeslot 16, from a specific CSTi timeslot; and similarly, maps receive PCM30 timeslot 16, to a specific CSTo timeslot. PCM30 timeslot 16 data is mapped to/from CST channel n (n=0 to 31), where n is the BCD equivalent of 16C4 to 16C0 with 16C4 being the most significant bit. 16C4 0 0 0 1 16C3 0 0 0 1 Bit Settings 16C2 16C1 0 0 0 0 0 1 etc. 1 1 16C0 0 1 0 1 Selected CST Timeslot 0 1 2 31
CCS (CSIG=1 of register address Y03) and CST (TS16E=1 of register address Y06) must be selected for these operations to be valid. 4 3 2 1 0 15C4 15C3 15C2 15C1 15C0 (01111) Timeslot 15 CST Map Bits. The selection of these bits results in a mapping of the transmit PCM30 timeslot 15, from a specific CSTi timeslot; and similarly, maps receive PCM30 timeslot 15, to a specific CSTo timeslot. PCM30 timeslot 15 data is mapped to/from CST channel n (n=0 to 31), where n is the BCD equivalent of 15C4 to 15C0 with 15C4 being the most significant bit. 15C4 0 0 0 1 15C3 0 0 0 1 Bit Settings 15C2 15C1 0 0 0 0 0 1 etc. 1 1 15C0 0 1 0 1 Selected CST Timeslot 0 1 2 31
CCS (CSIG=1 of register address Y03) and CST (TS15E=1 of register address Y06) must be selected for these operations to be valid. Table 149 - CCS to ST-BUS CSTi and CSTo Map Control Register (R/W Address Y07) (E1)
SEMICMF.019
167
MT9072
Bit 15 14 13 Name # Sa4SS (00) not used. Functional Description
Data Sheet
Sa4 Source Select. These 2 bits determine the source of the transmit Sa4 bits in timeslot 0 of NFAS frames. Select Bits: Sa4 Source 00 Transmit National Data Register (YB0) 01 TxDL pin (received Sa4 bits are sent to the RxDL pin) 10 DSTi pin (ST-BUS Channel 0, Bit 4 in NFAS frames) 11 HDLC (Transmit and Receive Sa4 bits) Note the received Sa4 bits are always available in the RX National Data Bit Buffer (YC0) and timeslot 0 on the DSTo pin. Sa5 Source Select. These 2 bits determine the source of the transmit Sa5 bits in timeslot 0 of NFAS frames. Select Bits: Sa5 Source 00 Transmit National Data Register (YB1) 01 TxDL pin (received Sa5 bits are sent to the RxDL pin) 10 DSTi pin (ST-BUS Channel 0, Bit 3 in NFAS frames) 11 HDLC (Transmit and Receive Sa5 bits) Note the received Sa5 bits are always available in the RX National Data Bit Buffer (YC1) and timeslot 0 on the DSTo pin. Sa6 Source Select. These 2 bits determine the source of the transmit Sa6 bits in timeslot 0 of NFAS frames. Select Bits: Sa6 Source 00 Transmit National Data Register (YB2) 01 TxDL pin (received Sa6 bits are sent to the RxDL pin) 10 DSTi pin (ST-BUS Channel 0, bit 2 in NFAS frames) 11 HDLC (Transmit and Receive Sa6 bits) Note the received Sa6 bits are always available in the RX National Data Bit Buffer (YC2) and timeslot 0 on the DSTo pin. Sa7 Source Select. These 2 bits determine the source of the transmit Sa7 bits in timeslot 0 of NFAS frames. Select Bits: Sa7 Source 00 Transmit National Data Register (YB3) 01 TxDL pin (received Sa7 bits are sent to the RxDL pin) 10 DSTi pin (ST-BUS Channel 0, Bit 1 in NFAS frames) 11 HDLC (Transmit and Receive Sa7 bits) Note the received Sa7 bits are always available in the RX National Data Bit Buffer (YC3) and timeslot 0 on the DSTo pin. Sa8 Source Select. These 2 bits determine the source of the transmit Sa8 bits in timeslot 0 of NFAS frames. Select Bits: Sa8 Source 00 Transmit National Data Register (YB4) 01 TxDL pin (received Sa8 bits are sent to the RxDL pin) 10 DSTi pin (ST-BUS Channel 0, Bit 1 in NFAS frames) 11 HDLC (Transmit and Receive Sa8 bits) Note the received Sa8 bits are always available to the RX National Data Bit Buffer (YC4) and timeslot 0 on the DSto pin. not used. Table 150 - DataLink Control Register (R/W Address Y08) (E1)
14 13
Sa5SS (00)
10 9
Sa6SS (00)
8 7
Sa7SS (00)
6 5
Sa8SS (00)
4-2
#
168
SEMICMF.019
Data Sheet
Bit 1 Name E4CK (0) Functional Description
MT9072
Extracted 4 Data Link Clock. If one, the RxDLC pin outputs an ST-BUS type 4.096MHz clock signal derived from a doubled 2.048MHz clock signal at the EXCLi pin. This clock is synchronous with the receive data before it passes through the elastic buffer at the RxDL pin, or at the DSTo pin if control bit ELAS (register address Y03) is disabled. If zero, the RxDLC pin operates as a receive data link clock or enable signal as programmed by control bit DLCK (register address Y08). Data Link Clock. If one, the TxDLC and RxDLC pins output a gapped clock. If zero, the TxDLC and RxDLC pins output an active low enable signal. The above only applies for the national bits enabled for DL pin operation (by the Sa4-8 bits of register address Y03). See Figures 30 to 34. Table 150 - DataLink Control Register (R/W Address Y08) (E1)
0
DLCK (0)
Bit 15-8 7-0
Name # not used.
Functional Description
RXIDC Receive Idle Code. This is the idle code that is sent on the DSTochannels if the per timeslot 7-0 control bit MPDR is set(Y90-YAF). Note that bit 7 is sent out first. (0) Table 151 - Receive Idle Code Register(Y09) (E1)
Bit 15-8 7-0
Name # not used.
Functional Description
TXIDC Transmit Idle Code. This is the idle code that is sent on the PCM30 channels if the per timeslot 7-0 control bit MPDT is set(Y90-YAF) (0) Table 152 - Transmit Idle Code Register(Y0A) (E1)
16.2.3
Master Status Registers (Y10 - Y1A) Bit Functions
Tables 158 to 172 describe the bit functions of each of the Master Status Registers in the MT9072 in E1 mode. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11-A8).
Bit 15 14 13
Name # RSLP RSLPD not used.
Functional Description
Receive Slip. This bit changes state when a receive controlled frame slip has occurred. Receive Slip Direction. If one, indicates that the last received frame slip (RSLP toggled of register Y10) resulted in a repeated frame. This would occur if the system clock (CKi/2) was faster than the network clock (EXCLi). If zero, indicates that the last received frame slip (RSLP) resulted in a lost frame. This would occur if the system clock (CKi/2) was slower than the network clock (EXCLi). Updated on an RSLP occurrence basis.
Table 153 - Synchronization & CRC-4 Remote Status (R Address Y10) (E1)
SEMICMF.019
169
MT9072
Bit 12 Name BSYNC Functional Description
Data Sheet
Receive Basic Frame Alignment. If zero, indicates the received PCM30 link basic frame alignment pattern (x0011011 in timeslot 0 of alternate frames) is acquired; if one, the basic frame alignment pattern is lost or not acquired.
11
MSYNC Receive Multiframe Alignment. If zero, indicates the received PCM30 link signaling multiframe alignment signal (0000xxxx in timeslot 16 of every16th frame) is acquired; if one, the signaling multiframe alignment signal is lost or not acquired. CSYNC Receive CRC-4 Synchronization. If zero, indicates the received PCM30 link CRC-4 multiframe alignment pattern (001011xx in timeslot 0, in bit position 1 of 16 alternate frames) is acquired; if one, the CRC-4 multiframe alignment pattern is lost or not acquired. RED Alarm. If one, indicates that basic frame alignment (BSYNC of register address Y10) has been lost for at least 100 msec. This bit is cleared (zero) when basic frame alignment is acquired. Consecutively Errored Frame Alignment Signal. If one, the last two frame alignment signals (FAS=0011011) were received in error. If zero, at least one of the last two frame alignment signals were received without error. A non-errored FAS would result in the RFA status bits (register address Y13) set as follows, RFA2=0, RFA3=0, RFA4=1, RFA5=1, RFA6=0, RFA7=1, RFA8=1 not used. Remote CRC-4 and RAI T10. If one, the received A bits were one and the received E bits were zero (RCRCR register address Y10) continuously for more than 10ms. See I.431 section 3.4.1.2 on RAI and continuous CRC error information. Remote CRC-4 and RAI T450. If one, the received A bits were one and the received E bits were zero (RCRCR register address Y10) continuously for more than 10ms but less than 450ms. See I.431 section 3.4.1.2 on RAI and continuous CRC error information. Remote CRC-4 Multiframe Generator/Detector Failure. If one, each of the previous five seconds have an E-bit (E1 + E2) of error count of greater than 989 (E-bit counter 3DD hex or 11 1101 1101 address Y17), and for this same period the receive RAI bit (register addressY12 and Y13) was zero (no remote alarm), and for the same period the BSYNC bit (register address Y10) was equal to zero (basic frame alignment has been maintained). If zero, indicates normal operation. Receive E1 Bit Status. Indicates the status of the bit (E1) received on the PCM30 link in bit position 1 of timeslot 0 in non-frame alignment signal (NFAS) frame 13. If zero, the remote end calculated a CRC-4 error in its received sub-multiframe one. If one, no error was calculated. Table 153 - Synchronization & CRC-4 Remote Status (R Address Y10) (E1)
10
9
RED
8
CEFS
7 6
# RCRC0
5
RCRC1
4
RFAIL
3
REB1
170
SEMICMF.019
Data Sheet
Bit 2 Name REB2 Functional Description
MT9072
Receive E2 Bit Status. Indicates the status of the bit (E2) received on the PCM30 link in bit position 1 of timeslot 0 in non-frame alignment signal (NFAS) frame 15. If zero, the remote end calculated a CRC-4 error in its received sub-multiframe two. If one, no error was calculated.
1
RCRCR Remote CRC-4 and RAI. If one, the RAI (A) status bit (register address Y12 and Y13) is one, and the REB1 (E1) and REB2 (E2) status bits (register address Y10) are zero. If zero, the above requirement is not met. CRCIW CRC-4 Interworking. If one, indicates the CRC-4 interworking status is CRC-4 to CRC-4 (local to remote). The transmit PCM30 link is framed to CRC-4 with E1 and E2 bits sent, and the receive PCM30 link is treated as CRC-4 with E1 and E2 bits received. If zero, indicates the CRC-4 interworking status is CRC-4 to non-CRC (local to remote). In this case, the transmit PCM30 link is framed to CRC-4 but the E1 and E2 bits are not sent, and the receive PCM30 link is not treated as a CRC-4 multiframe but only as a basic frame and signaling multiframe frame only.
0
Table 153 - Synchronization & CRC-4 Remote Status (R Address Y10) (E1)
SEMICMF.019
171
MT9072
Bit 15-13 13 12 11 Name ## not used. Functional Description
Data Sheet
ONESEC One Second Timer Status. This bit toggles from low to high once every one second, and is synchronous with the applied125us frame pulse at pin FPi. TWOSEC Two Second Timer Status. This bit toggles from low to high once every two seconds, and is synchronous with the applied125us frame pulse at pin FPi. T1 Timer 1. If one, indicates that a receive PCM30 link with non-normal operational CRC-4 frames (CSYNC=1 of register address Y10) has persisted for at least 100ms. This bit is zero when Timer 2 (T2 of register address Y11) is one. Refer to I.431 Section 5.9.2.2.3. Timer 2. If one, indicates that a receive PCM30 link with normal operational CRC-4 frames (CSYNC=0 of register address Y11) has persisted for at least 10ms. This bit is cleared (zero) when non-normal operational frames (CSYNC=1) occur. Refer to I.431 Section 5.9.2.2.3. 400ms Timer Status. This is the 400ms CRC-4 multiframe alignment timer. This bit initially changes state from zero to one synchronously with the T8 (register address Y11) bit after the T8 bit has consecutively toggled 50 times (400ms). While this condition persists (T8=0101 etc.), the T400 bit continues to change state every 400ms. The T400 bit is cleared (zero) with the T8 bit when CRC-4 multiframe synchronization is acquired (CSYNC =0). 8ms Timer Status. This is the 8ms CRC-4 multiframe alignment timer. This bit initially changes state from zero to one synchronously with the CRCRF (register address Y11) bit when the received PCM30 link CRC-4 multiframe synchronization (CSYNC of register address Y10) could not be found within the time out period of 8 ms after detecting basic frame synchronization (BSYNC=0 of register address Y10). While this condition persists (CRCRF=1), the T8 bit continues to change state every 8ms. The T8 bit is cleared (zero) with the CRCRF bit when CRC-4 multiframe synchronization is acquired (CSYNC =0). not used. CRC-4 Alignment 2ms Timer. When CRC-4 multiframe alignment has not been achieved (CSYNC=1 of register address Y10), this bit asynchronously changes state every 2 ms. When CRC-4 multiframe alignment has been achieved (CSYNC =0), this bit still changes state every 2 ms, but is synchronous with the receive CRC-4 multiframe signal. CRC-4 Reframe. If one, indicates the received PCM30 link CRC-4 multiframe synchronization (CSYNC of register address Y10) could not be found within the time out period of 8ms after detecting basic frame synchronization (BSYNC of register address Y10). This bit is cleared (zero) when CRC-4 multiframe synchronization is acquired (CSYNC =0). Receive CRC-4 Error Status One. If one, the CRC-4 evaluation of the last received PCM30 link submultiframe 1 resulted in an error (the calculated C1,C2,C3,C4 CRC-4 remainder bits did not match the received CRC-4 remainder C1,C2,C3,C4 bits). If zero, the last submultiframe 1 was error free. Updated on a submultiframe 1 basis. Receive CRC-4 Error Status Two. If one, the CRC-4 evaluation of the last received PCM30 link submultiframe 2 resulted in an error (the calculated C1,C2,C3,C4 CRC-4 remainder bits did not match the received CRC-4 remainder C1,C2,C3,C4 bits). If zero, the last submultiframe 2 was error free. Updated on a submultiframe 2 basis. not used. Table 154 - CRC-4 Timers & CRC-4 Local Status (R Address Y11) (E1)
10
T2
9
T400
8
T8
7-5 4
### CALN
3
CRCRF
2
CRCS1
1
CRCS2
0
(#)
172
SEMICMF.019
Data Sheet
Bit 15-14 13 12 Name ## KLVE LOSS not used. Functional Description
MT9072
Keep Alive. If one, indicates that the AIS status bit (register address Y12) has been one for at least 100ms. This bit is zero when AIS is zero. Refer to I.431. Loss of Signal Status Indication. If one, indicates the presence of a loss of signal condition on the received PCM30 link. A loss of signal condition occurs when 192 or 32(selectable by L32Z in Y01) consecutive bit periods are zero. A loss of signal condition terminates when an average ones density of at least 12.5% has been received over a period of 255 contiguous pulse positions starting with a pulse. If zero, indicates normal operation. Alarm Indication Signal 16 Status. If one, indicates an all ones signal (1111 1111) is being received in timeslot16 of the received PCM30 link for the current frame. Updated on a basic frame basis. If zero, normal operation. Alarm Indication Status Signal. If one, indicates that an Alarm Indication Signal (AIS) is detected on the received PCM30 link. The criteria (i.e. less than three zeros in a two frame period) for AIS detection is determined by the control bit ASEL (register address Y00). If the AIS bit is zero, indicates that an AIS signal not being received. Remote Alarm Indication Status. Indicates the status of the bit (A-bit) received on the PCM30 link in bit position 3 of timeslot 0 of the non-frame alignment signal (NFAS) frames. If one, there is currently a remote alarm condition. Updated on a NFAS frame basis. This bit is identical to the RAI bit of register address Y13 and is duplicated here for convenience. Auxiliary Pattern. If one, an auxiliary pattern (101010) of at least 512 bits is being received on the PCM30 link. If zero, an auxiliary pattern is not being received. This pattern will be decoded in the presents of a bit error rate of as much as 10-3. Receive Multiframe Alignment Bits One to Four. Indicates the status of the bits received on the PCM30 link in bit positions one to four of timeslot 16 of frame 0 of the multiframe alignment signal (MAS). These bits should be 0000 for proper signaling multiframe alignment. Updated on a MAS frame basis. Receive Spare Bit X1. Indicates the status of the bit received on the PCM30 link in bit position five of timeslot 16 of frame 0 of the multiframe alignment signal (MAS). Updated on a MAS frame basis. Receive Y-bit. Indicates the status of the bit (Y-bit) received on the PCM30 link in bit position six of timeslot 16 of frame 0 of the multiframe alignment signal (MAS). Updated on a MAS frame basis. If one, typically indicates a loss of multiframe alignment at the remote end. If zero, typically indicates acquired multiframe alignment at the remote end. Receive Spare Bits X2 and X3. Indicates the status of the bits received on the PCM30 link in bit positions seven and eight of timeslot 16 of frame 0 of the multiframe alignment signal (MAS). Updated on a MAS frame basis.
11
AIS16
10
AIS
9
RAI
8
AUXP
7 6 5 4 3
RMA1 RMA2 RMA3 RMA4 X1
2
Y
1 0
X2 X3
Table 155 - Alarms & Multiframe Signaling (MAS) Status (R Address Y12) (E1)
SEMICMF.019
173
MT9072
Bit 15 Name RIU1 Functional Description
Data Sheet
Receive International Use 1. Indicates the status of the bit received on the PCM30 link in bit position one of timeslot 0 of the non-frame alignment signal (NFAS) frames. This bit is the CRC4 multiframe alignment bit (001011) of the NFAS frames (1,3,5,7,9,11) when CRC-4 multiframing is used. Or, this bit is used for international use. Receive Non-Frame Alignment Bit. Indicates the status of the bit received on the PCM30 link in bit position two of timeslot 0 of the non-frame alignment signal (NFAS) frames. This bit should be one and identifies the frame as an NFAS frame (the FAS frame should have a zero in bit position two of timeslot 0). Remote Alarm Indication Status. Indicates the status of the bit (A-bit) received on the PCM30 link in bit position 3 of timeslot 0 of the non-frame alignment signal (NFAS) frames. If one, there is currently a remote alarm condition. Updated on a NFAS frame basis. This bit is identical to the RAI bit of register address Y12 and is duplicated here for convenience. Receive National Use Four to Eight. Indicates the value of the Sa bits received on the PCM30 link in bit positions four to eight of timeslot 0 of the non-frame alignment signal (NFAS) frames. Sa4 corresponds to RNU4, Sa5 to RNU5 and so on up to Sa8 to RNU8. Updated on a NFAS frame basis. Receive International Use Zero. Indicates the status of the bit received on the PCM30 link in bit position one of timeslot 0 of the frame alignment signal (FAS) frames. This bit is the CRC-4 remainder bit (C1,C2,C3 or C4) of the FAS frames when CRC-4 multiframing is used. Or, this bit is used for international use. Receive Frame Alignment Signal (FAS) Bits 2 to 8. Indicates the value of the bits received on the PCM30 link in bit positions two to eight of timeslot 0 of the frame alignment signal (FAS) frames. These bits form the FAS and should have the value of 0011011.
14
RNFA
13
RAI
12 11 10 9 8 7
RNU4 RNU5 RNU6 RNU7 RNU8 RIU0
6 5 4 3 2 1 0
RFA2 RFA3 RFA4 RFA5 RFA6 RFA7 RFA8
Table 156 - Non-Frame Alignment (NFAS) Signal and Frame Alignment Signal (FAS) Status (R Address Y13) (E1)
174
SEMICMF.019
Data Sheet
Bit 15-12 Name #### not used. Functional Description
MT9072
Phase Indicator. These 12 bits are an indication of the delay through the receive slip buffer and the imminence of a receive frame slip. The read address is this register's value plus 16 bits and is updated when the write address is zero. The slip buffer contains 512 bits on 64 channels (0 thru 63). The accuracy of this indicator is approximately 1/16 of a bit. 11 10 9 8 7 6 5 4 3 2 1 0 PI11 PI10 PI9 PI8 PI7 PI6 PI5 PI4 PI3 PI2 PI1 PI0 This bit indicates a 1 frame (32 timeslot or 256 bit) phase offset. This bit indicates a 16 timeslot (128 bit) phase offset. This bit indicates a 4 timeslot (64 bit) phase offset. This bit indicates a 3 timeslot (32 bit) phase offset. This bit indicates a 2 timeslot (16 bit) phase offset. This bit indicates a 1 timeslot (8 bit) phase offset. This bit indicates a 4 bit phase offset. This bit indicates a 2 bit phase offset. This bit indicates a 1 bit phase offset. This bit indicates a 1/2 bit phase offset. This bit indicates a 1/4 bit phase offset. This bit indicates a 1/8 bit phase offset. Table 157 - Phase Indicator Status (R Address Y14) (E1)
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Name PEC7 PEC6 PEC5 PEC4 PEC3 PEC2 PEC1 PEC0 PCC7 PCC6 PCC5 PCC4 PCC3 PCC2 PCC1 PCC0
Functional Description Pseudo Random Bit Sequence (PRBS) Error Counter. These bits make up a counter which is incremented for each pseudo random bit sequence (PRBS) (215-1) error detected on any of the DSTo receive channels connected (ADSEQ=0 register address Y01, RRSTn=1 register address Y90 to YAF) to the PRBS error detector. This counter is cleared with an overflow, a RESET (RESET pin or RST bit), or may be set by writing the desired value to it. PEC0 is the least significant bit (LSB). The lower byte and upper byte of register cannot be written to independently. Pseudo Random Bit Sequence (PRBS) CRC-4 Counter. These bits make up a counter which is incremented for each received CRC-4 multiframe. This counter is cleared with an overflow, a RESET (RESET pin or RST bit), or may be set by writing the desired value to it. PCC0 is the least significant bit (LSB). The lower byte and upper byte of register cannot be written to independently.
Table 158 - PRBS Error Counter & PRBS CRC-4 Counter (R/W Address Y15) (E1)
SEMICMF.019
175
MT9072
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name SLC15 SLC14 SLC13 SLC12 SLC11 SLC10 SLC9 SLC8 SLC7 SLC6 SLC5 SLC4 SLC3 SLC2 SLC1 SLC0 Functional Description
Data Sheet
Loss of Basic Frame Synchronization Counter. These bits make up a counter which is incremented for each 125us period in which basic frame synchronization (BSYNC=1 status register address Y10) is lost. This counter is cleared by a basic frame synchronization to a loss of basic frame synchronization state transition (BSYNC=0 to 1), or with an overflow, a RESET (RESET pin or RST bit), or it may be set by writing the desired value to it. SLC0 is the least significant bit (LSB).
Table 159 - Loss of Basic Frame Synchronization Counter with Auto Clear (R/W Address Y16) (E1)
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Name EEC15 EEC14 EEC13 EEC12 EEC11 EEC10 EEC9 EEC8 EEC7 EEC6 EEC5 EEC4 EEC3 EEC2 EEC1 EEC0
Functional Description E-bit Error Counter. These bits make up a counter which is incremented for each received PCM30 CRC-4 submultiframe E-bit error. This counter is cleared with an overflow, a RESET (RESET pin or RST bit), or may be set by writing the desired value to it. EEC0 is the least significant bit (LSB).
Table 160 - E-bit Error Counter (R/W Address Y17) (E1)
176
SEMICMF.019
Data Sheet
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name VEC15 VEC14 VEC13 VEC12 VEC11 VEC10 VEC9 VEC8 VEC7 VEC6 VEC5 VEC4 VEC3 VEC2 VEC1 VEC0 Functional Description
MT9072
Bipolar Violation Error Counter. These bits make up a counter which is incremented for each received bipolar violation error. This counter is cleared with an overflow, a RESET (RESET pin or RST bit), or may be set by writing the desired value to it. VEC0 is the least significant bit (LSB).
Table 161 - Bipolar Violation (BPV) Error Counter (R/W Address Y18) (E1)
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Name CEC15 CEC14 CEC13 CEC12 CEC11 CEC10 CEC9 CEC8 CEC7 CEC6 CEC5 CEC4 CEC3 CEC CEC1 CEC0
Functional Description CRC-4 Error Counter. These bits make up a counter which is incremented for each calculated CRC-4 submultiframe error (see CRCS1 and CRCS2 bits of register address Y11). This counter is cleared with an overflow, a RESET (RESET pin or RST bit), or may be set by writing the desired value to it. CEC0 is the least significant bit (LSB).
Table 162 - CRC-4 Error Counter (R/W Address Y19) (E1)
SEMICMF.019
177
MT9072
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name BEC7 BEC6 BEC5 BEC4 BEC3 BEC2 BEC1 BEC0 FEC7 FEC6 FEC5 FEC4 FEC3 FEC2 FEC1 FEC0 Functional Description
Data Sheet
Frame Alignment Signal (FAS) Bit Error Counter. These bits make up a counter which is incremented for each individual error in the received PCM30 link basic frame alignment signal (FAS) pattern (x0011011 in timeslot 0 of alternate frames). This counter is cleared with an overflow, a RESET (RESET pin or RST bit), or it may be set by writing the desired value to it. BEC0 is the least significant bit (LSB). The lower byte and upper byte of register cannot be written to independently.
Frame Alignment Signal (FAS) Error Counter. These bits make up a counter which is incremented for each combined (one or more) error in the received PCM30 link basic frame alignment signal (FAS) pattern (x0011011 in timeslot 0 of alternate frames). This counter is cleared with an overflow, a RESET (RESET pin or RST bit), or it may be set by writing the desired value to it. FEC0 is the least significant bit (LSB). The lower byte and upper byte of register cannot be written to independently.
Table 163 - Frame Alignment Signal (FAS) Bit Error Counter & FAS Error Counter (R/W Address Y1A) (E1)
Bit 15-12 11 10 9 8
Name #### RXclk TXclk Vcrc Vaddr not used.
Functional Description
This bit represents the receiver clock generated after the RXEN control bit, but before zero deletion is considered. This bit represents the transmit clock generated after the TXEN control bit, but before zero insertion is considered. This is the CRC recognition status bit for the receiver. Data is clocked into the register and then this bit is monitored to see if comparison was successful (bit will be high). This is the address recognition status bit for the receiver. Data is clocked into the Address Recognition Register and then this bit is monitored to see if comparison was successful (bit will be high). Transmit Byte Counter Position. These 7 bits provide the position of the Transmit HDLC Byte Counter register (YF6). The counter is decremented as a byte of data is sent through the Transmit FIFO. When this register reaches the count of one, the next write to the Tx FIFO will be tagged as an end of packet byte. The counter decrements at the end of the write to the Tx FIFO. If the Cycle bit of YF2 is set high, the counter will cycle through the programmed value continuously.
7-0
TBP7-0
Table 164 - Transmit Byte Counter Position and HDLC Test Status(Y1C) (E1)
178
SEMICMF.019
Data Sheet
Bit 6 Name IDC Functional Description
MT9072
Idle Channel State. Is set to a 1 when an idle Channel state (15 or more ones) has been detected at the receiver. This is an asynchronous event. On power reset, this may be 1 if the clock (RXC) was not operating. Status becomes valid after the first 15 bits or the first zero is received. RQ9-8 Byte Status bits from RX FIFO. These bits determine the status of the byte to be read from RX FIFO as follows: 00 Packet Byte 01 First Byte 10 Last byte of good packet 11 Last byte of bad packet
5-4
RQ9-8
3-2
TXSTAT1-0 Transmit FIFO Status: 00 Transmit FIFO is full. 01 The number of bytes in the transmit FIFO has reached or exceeded 16 bytes 10 Transmit FIFO is empty 11 The number of bytes in the TX FIFO is less than the 16 byte threshold. RXSTAT1-0 Receive FIFO Status: 00 Receive FIFO is full. 01 The number of bytes in the Receive FIFO has reached or exceeded 16 bytes 10 Receive FIFO is empty 11 The number of bytes in the Receive FIFO is less than the 16 byte threshold. Table 165 - HDLC Status Register(Y1D) (E1)
1-0
Bit 15-0
Name RCRC15-0
Functional Description Received CRC. The CRC received from the transmitter. The LSB of the FCS sequence is MSB in this register. This register is updated at the end of each received packet and therefore should be read when end of packet is detected. Table 166 - HDLC Receive CRC(Y1E) (E1)
Bit 7-0
Name RXFIFO7-0
Functional Description Receive FIFO.This is the received data byte read from the RX FIFO. The status bits of this byte can be read from the status register. The FIFO status is not changed immediately when a write or read occurs. It is updated after the data has settled and the transfer to the last available position has finished. Table 167 - HDLC Receive FIFO(Y1F) (E1)
SEMICMF.019
179
MT9072
16.2.4 Latched Status Registers (Y2X) Bit Functions
Data Sheet
Tables 173 to 181 describe the bit functions of each of the Latched Status Registers in the MT9072 in E1 mode. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11A8). All latched status registers will be reset in the inactive state upon reset.
Bit 15-9 8 7
Name ####### GAL EOPDL not used.
Functional Description
Go Ahead received Latch.Indicates a go-ahead pattern (01111111) was detected by the HDLC receiver. This bit is reset after a read. End of Packet Data Latch.This bit is set when an end of packet (EOP) byte was written into the RX FIFO by the HDLC receiver. This can be in the form of a flag, an abort sequence or as an invalid packet. This bit is reset after a read. Transmit End of Packet Latch.This bit is set when the transmitter has finished sending the closing flag of a packet or after a packet has been aborted. This bit is reset after read. End of Packet received latch.This bit is set when the byte about to be read from the RX FIFO is the last byte of the packet. It is also set if the Rx FIFO is read and there is no data in it. This bit is reset after a read. Transmit Fifo Low Latch.This bit is set when the Tx FIFO is emptied below the selected low threshold level. This bit is reset after a read. Framer Abort Latch. This bit (FA) is set when a frame abort is received during packet reception. It must be received after a minimum number of bits have been received (26) otherwise it is ignored. Txunder Latch.This bit is set for a TX FIFO underrun indication. If high it Indicates that a read by the transmitter was attempted on an empty Tx FIFO. This bit is reset after a read. Receive Fifo Full Latch.This bit is set when the Rx FIFO is filled above the selected full threshold level. This bit is reset after a read. Receive Overflow Latch.Indicates that the 32 byte RX FIFO overflowed (i.e. an attempt to write to a 32byte full RX FIFO). The HDLC will always disable the receiver once the receive overflow has been detected. The receiver will be re-enabled upon detection of the next flag, but will overflow again unless the RX FIFO is read. This bit is reset after a read. Table 168 - HDLC Status Latch(Y23) (E1)
6 5
TEOPL EOPRL
4 3
TXFL FAL
2 1 0
TXunder RxffL RxOvfL
180
SEMICMF.019
Data Sheet
Bit 15 14 Name # not used. Functional Description
MT9072
RCRCRL Remote CRC-4 and RAI Latch. When the RCRCR status bit (register address Y10) toggles from zero to one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. RSLPL Receive Slip Latch. When the RSLP status bit (register address Y13) toggles from zero to one, or from one to zero, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Receive Y-bit Latch. When the Y status bit (register address Y12) toggles from zero to one, or from one to zero, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Auxiliary Pattern Latch. When the AUXP status bit (register address Y12) toggles from zero to one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Remote Alarm Indication Status Latch. When the RAI (A) status bit (register address Y12 and Y13) toggles from zero to one, or from one to zero, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Alarm Indication Status Signal Latch. When the AIS status bit (register address Y12) toggles from zero to one, or from one to zero, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Alarm Indication Signal 16 Status Latch. When the AIS16 status bit (register address Y12) toggles from zero to one, or from one to zero, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Loss of Signal Status Indication Latch. When the LOSS status bit (register address Y12) toggles from zero to one, or from one to zero, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Remote CRC-4 and RAI T10 Latch. When the RCRC0 status bit (register address Y10) toggles from zero to one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Remote CRC-4 and RAI T450 Latch. When the RCRC1 status bit (register address Y10) toggles from zero to one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Consecutively Errored Frame Alignment Signal Latch. When the CEFS status bit (register address Y10) toggles from zero to one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. Remote CRC-4 Multiframe Generator/Detector Failure Latch. When the status bit (register address Y10) toggles from zero to one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read.
13
12
YL
11
AUXPL
10
RAIL
9
AISL
8
AIS16L
7
LOSSL
6
RCRC0L
5
RCRC1L
4
CEFSL
3
RFAILL
Table 169 - Sync, CRC-4 Remote, Alarms, MAS and Phase Latched Status Register (Address Y24) (E1)
SEMICMF.019
181
MT9072
Bit 2 Name Functional Description
Data Sheet
CSYNCL Receive CRC-4 Synchronization Latch. When the CSYNC status bit (register address Y10) toggles from zero to one, or from one to zero, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. MSYNCL Receive Multiframe Alignment Latch. When the MSYNC status bit (register address Y10) toggles from zero to one, or from one to zero, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read. BSYNCL Receive Basic Frame Alignment Latch. When the BSYNC status bit (register address Y10) toggles from zero to one, or from one to zero, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y34) is read.
1
0
Table 169 - Sync, CRC-4 Remote, Alarms, MAS and Phase Latched Status Register (Address Y24) (E1)
182
SEMICMF.019
Data Sheet
Bit 15 14 Name # not used. Functional Description
MT9072
SLOL Loss of Sync Counter Overflow Latch. When the Loss of Sync Counter (SLC15-0 register address Y16) overflows (3FF to 00), this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read. FEOL Frame Alignment Signal (FAS) Error Counter Overflow Latch. When the FAS Error Counter (FEC7-0 register address Y1A lower byte) overflows (FF to 00), this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read. FEIL Frame Alignment Signal (FAS) Error Counter Indication Latch. When the FAS Error Counter (FEC7-0 register address Y1A lower byte) is incremented by one, this status bit is latched to one. This bit is cleared when either this register or the interrupt status register (register address Y35) is read.
13
12
11
BEOL Frame Alignment Signal (FAS) Bit Error Counter Overflow Latch. When the FAS Bit Error Counter (BEC7-0 register address Y1A upper byte) overflows (FF to 00), this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read. BEIL Frame Alignment Signal (FAS) Bit Error Counter Indication Latch. When the FAS Bit Error Counter (BEC7-0 register address Y1A upper byte) is incremented by one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read.
10
9
CEOL CRC-4 Error Counter Overflow Latch. When the CRC-4 Error Counter (CEC15-0 register address Y19) overflows (3FF to 000), this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read. CEIL CRC-4 Error Counter Indication Latch. When the CRC-4 Error Counter (CEC15-0 register address Y19) is incremented by one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read.
8
7
VEOL Bipolar Violation (BPV) Error Counter Overflow Latch. When the BPV Error Counter (VEC15-0 register address Y18) overflows (FFFF to 000), this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read. VEIL Bipolar Violation (BPV) Error Counter Indication Latch. When the BPV Error Counter (VEC15-0 register address Y18) is incremented by one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read.
6
5
EEOL E-Bit Error Counter Overflow Latch. When the E-Bit Error Counter (EEC15-0 register address Y17) overflows (3FF to 000), this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read. EEIL E-Bit Error Counter Indication Latch. When the E-Bit Error Counter (EEC15-0 register address Y17) is incremented by one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read.
4
3
PCOL PRBS CRC-4 Counter Overflow Latch. When the PRBS CRC-4 Counter (PCC7-0 register address Y15 lower byte) overflows (FF to 00), this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read. # not used.
2
Table 170 - Counter Indication and Counter Overflow Latched Status Register (Address Y25) (E1)
SEMICMF.019
183
MT9072
Bit 1 Name Functional Description
Data Sheet
PEOL PRBS Error Counter Overflow Latch. When the PRBS Error Counter (PEC7-PEC0 register address Y15 upper byte) overflows (FF to 00), this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read. PEIL PRBS Error Counter Indication Latch. When the PRBS Error Counter (PEC7-PEC0 register address Y15 upper byte) is incremented by one, this status bit is latched to one. This bit is cleared when either this register, or the interrupt status register (register address Y35) is read.
0
Table 170 - Counter Indication and Counter Overflow Latched Status Register (Address Y25) (E1)
Bit 15 14
Name # Sa5VL not used.
Functional Description
Sa5 Bit Value Latch. This is the latched value of the Sa5 National bit when the Sa6N8L bit toggles to one. The Sa5VL bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read. Sa6 Nibble (bit 3 to 0) Value Latch. This is the latched value of the Sa6 National bits nibble (bits 3 to 0) when the Sa6N8L bit toggles to one. These bits are cleared when either this register, or the corresponding interrupt status register (register address Y36) is read. Sa6 Nibble Eight Consecutive Times Status Latch. When eight consecutive identical receive Sa6 National bit nibble patterns are received (per sub-multiframe), this status bit is latched to one. This bit is set on a CRC-4 sub-multiframe basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read. Sa6 Nibble Change Status Latch. When a received Sa6 National bit nibble (per submultiframe) changes value, this status bit is latched to one. This bit is set on a CRC-4 submultiframe basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read. Sa Nibble Change Status Latch. When any receive National (i.e. Sa5,Sa6,Sa7 or Sa8) bits nibbles changes value, this status bit is latched to one. This bit is set on a CRC-4 submultiframe basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read. Sa5 Bit Change Status Latch. When a received Sa5 National bit changes value, this status bit is latched to one. This bit is set on a CRC-4 NFAS frame basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read. Sa Bit Change Status Latch. When any receive National (i.e. Sa5,Sa6,Sa7 or Sa8) bit changes value, this status bit is latched to one. This bit is set on a CRC-4 NFAS frame basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read. Receive Channel Associated Signaling (CAS) Change Latch. When any of the receive CAS (i.e. ABCD) bits in the Receive CAS Data Registers (address Y70-Y8F) change state, this status bit is latched to one. This bit is set on a basic frame (FPi) basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y34) is read.
13 12 11 10 9
Sa6V3L Sa6V2L Sa6V1L Sa6V0L Sa6N8L
8
Sa6NL
7
SaNL
6
Sa5TL
5
SaTL
4
CASRL
Table 171 - CAS, National, CRC-4 Local and Timer Latched Status Register (Address Y26) (E1)
184
SEMICMF.019
Data Sheet
Bit 3 Name CALNL Functional Description
MT9072
CRC-4 Alignment 2ms Timer Latch. When the CALN status bit (register address Y11) toggles from zero to one, this status bit is latched to one. This bit is set on a 2ms or CRC-4 multiframe frame basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read. Timer 2 Latch. When the CRC-4 T2 (10ms) status bit (register address Y11) toggles from zero to one, this status bit is latched to one. This bit is set on a basic frame (FPi) basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read. Timer 1 Latch. When the CRC-4 T1 (100ms) status bit (register address Y11) toggles from zero to one, this status bit is latched to one. This bit is set on a basic frame (FPi) basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read.
2
T2L
1
T1L
0
ONESECL One Second Timer Status Latch. When the ONESEC status bit (register address Y11) toggles from zero to one, this status bit is latched to one. This bit is set on a basic frame (FPi) basis. This bit is cleared when either this register, or the corresponding interrupt status register (register address Y36) is read.
Table 171 - CAS, National, CRC-4 Local and Timer Latched Status Register (Address Y26) (E1)
Bit 15-4 3
Name # RAIP not used.
Functional Description
Remote Alarm Indication Status Persistent Latch. When the RAI (A) status bit (register address Y12 and Y13) toggles from zero to one, this status bit is latched to one. This bit is cleared when this register is read while the RAI status bit is zero. Alarm Indication Status Signal Persistent. When the AIS status bit (register address Y12) toggles from zero to one, this status bit is latched to one. This bit is cleared when this register is read while the AIS status bit is zero. Loss of Signal Status Indication Persistent Latch. When the LOSS status bit (register address Y12) toggles from zero to one, this status bit is latched to one. This bit is cleared when this register is read while the LOSS status bit is zero. Receive Basic Frame Alignment Persistent Latch. When the BSYNC status bit (register address Y10) toggles from zero to one, this status bit is latched to one. This bit is cleared when this register is read while the BSYNC status bit is zero.
2
AISP
1
LOSSP
0
BSYNCP
Table 172 - Performance Persistent Latched Status Register (Address Y27) (E1)
SEMICMF.019
185
MT9072
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name EEL15 EEL14 EEL13 EEL12 EEL11 EEL10 EEL9 EEL8 EEL7 EEL6 EEL5 EEL4 EEL3 EEL2 EEL1 EEL0 Functional Description
Data Sheet
E-bit Error Count Latch. These bits make up a latch which samples the current value of the E-Bit Error Counter (address Y17) on the rising edge of the internal one second timer (ONESEC register address Y11). This latch is cleared with a RESET (RESET pin or RST bit). EEL0 is the least significant bit (LSB).
Table 173 - E-Bit Error Count Latch (R Address Y28) (E1)
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Name VEL15 VEL14 VEL13 VEL12 VEL11 VEL10 VEL9 VEL8 VEL7 VEL6 VEL5 VEL4 VEL3 VEL2 VEL1 VEL0
Functional Description Bipolar Violation (BPV) Error Count Latch. These bits make up a latch which samples the current value of the Bipolar Violation (BPV) Error Counter (address Y18) on the rising edge of the internal one second timer (ONESEC register address Y11). This latch is cleared with a RESET (RESET pin or RST bit). VEL0 is the least significant bit (LSB).
Table 174 - Bipolar Violation (BPV) Error Count Latch (R/W Address Y29) (E1)
186
SEMICMF.019
Data Sheet
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name CEL15 CEL14 CEL13 CEL12 CEL11 CEL10 CEL9 CEL8 CEL7 CEL6 CEL5 CEL4 CEL3 CEL2 CEL1 CEL0 Functional Description
MT9072
CRC-4 Error Count Latch. These bits make up a latch which samples the current value of the CRC-4 Error Counter (address Y19) on the rising edge of the internal one second timer (ONESEC register address Y11). This latch is cleared with a RESET (RESET pin or RST bit). CEL0 is the least significant bit (LSB).
Table 175 - CRC-4 Error Count Latch (R/W Address Y2A) (E1)
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Name BEL7 BEL6 BEL5 BEL4 BEL3 BEL2 BEL1 BEL0 FEL7 FEL6 FEL5 FEL4 FEL3 FEL2 FEL1 FEL0
Functional Description Frame Alignment Signal (FAS) Bit Error Count Latch. These bits make up a latch which samples the current value of the Frame Alignment Signal (FAS) Bit Error Counter (upper byte of address Y1A) on the rising edge of the internal one second timer (ONESEC register address Y11). This latch is cleared with a RESET (RESET pin or RST bit). BEL0 is the least significant bit (LSB).
Frame Alignment Signal (FAS) Error Count Latch. These bits make up a latch which samples the current value of the Frame Alignment Signal (FAS) Error Counter (lower byte of address Y1A) on the rising edge of the internal one second timer (ONESEC register address Y11). This latch is cleared with a RESET (RESET pin or RST bit). FEL0 is the least significant bit (LSB).
Table 176 - Frame Alignment Signal (FAS) Error Count Latch (R/W Address Y2B) (E1)
SEMICMF.019
187
MT9072
16.2.5 Interrupt Vector and Interrupt Status Registers (Y3X) Bit Functions
Data Sheet
Tables 129 and 130 describes the bit functions of the Interrupt Vectors, while Tables 182 to 185 describe the bit functions of each of the Interrupt Status Registers in the MT9072. Each interrupt status register is repeated for each of the 8 framers (not the Interrupt Vectors). Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11-A8). However, since the Interrupt Vectors are common for all eight framers, only addresses 910 and 911 may be used to read from these registers. The (#) indicates that the unused bit position may be read as either a (0) or (1).
Bit 15-9 8 7
Name # GAI EOPDI not used.
Functional Description
Go Ahead Interrupt. Indicates a go-ahead pattern (01111111) was detected by the HDLC receiver. This bit is reset after a read. End of Packet Data Interrupt.This bit is set when an end of packet (EOP) byte was written into the RX FIFO by the HDLC receiver. This can be in the form of a flag, an abort sequence or as an invalid packet. This bit is reset after a read. Transmit End of Packet Interrupt.This bit is set when the transmitter has finished sending the closing flag of a packet or after a packet has been aborted. This bit is reset after read. End of Packet Receive Fifo Interrupt.This bit is set when the byte about to be read from the RX FIFO is the last byte of the packet. It is also set if the Rx FIFO is read and there is no data in it. This bit is reset after a read. Transmit FIFO Low Interrupt.This bit is set when the Tx FIFO is emptied below the selected low threshold level. This bit is reset after a read. Frame Abort: Transmit Interrupt. this bit (FA) is set when a frame abort is received during packet reception. It must be received after a minimum number of bits have been received (26) otherwise it is ignored. Transmit Elastic Buffer Empty Interrupt. If high it Indicates that a read by the transmitter was attempted on an empty Tx FIFO. This bit is reset after a read. Receive FIFO is filled above Threshold Interrupt.This bit is set when the Rx FIFO is filled above the selected full threshold level. This bit is reset after a read. Receive FiFO Overflow Interrupt. This bit Indicates that the 32 byte RX FIFO overflowed (i.e. an attempt to write to a 32 byte full RX FIFO). The HDLC will always disable the receiver once the receive overflow has been detected. The receiver will be re-enabled upon detection of the next flag, but will overflow again unless the RX FIFO is read. This bit is reset after a read. Table 177 - HDLC Interrupt Status Register(Y33) (E1)
6
TEOPI
5
EOPRI
4 3
TXFLI FAI
2 1 0
TXUNDERI RXFFI RXOVFLI
188
SEMICMF.019
Data Sheet
Bit 15 14 Name # RCRCRI not used. Functional Description
MT9072
Remote CRC-4 and RAI Interrupt. This bit is one when the corresponding latched status bit (RCRCRL, register address Y24) is set, and the corresponding mask bit is unmasked (RCRCRM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Receive Slip Interrupt. This bit is one when the corresponding latched status bit (RSLPL, register address Y24) is set, and the corresponding mask bit is unmasked (RSLPM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Receive Y-bit Interrupt. This bit is one when the corresponding latched status bit (YL, register address Y24) is set, and the corresponding mask bit is unmasked (YM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Auxiliary Pattern Interrupt. This bit is one when the corresponding latched status bit (AUXPL, register address Y24) is set, and the corresponding mask bit is unmasked (AUXPM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Remote Alarm Indication Status Interrupt. This bit is one when the corresponding latched status bit (RAIL, register address Y24) is set, and the corresponding mask bit is unmasked (RAIM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Alarm Indication Status Signal Interrupt. This bit is one when the corresponding latched status bit (AISL, register address Y24) is set, and the corresponding mask bit is unmasked (AISM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Alarm Indication Signal 16 Status Interrupt. This bit is one when the corresponding latched status bit (AIS16L, register address Y24) is set, and the corresponding mask bit is unmasked (AIS16M, register address Y44). This bit is cleared when either this register, or the latched status register is read. Loss of Signal Status Indication Interrupt. This bit is one when the corresponding latched status bit (LOSSL, register address Y24) is set, and the corresponding mask bit is unmasked (LOSSM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Remote CRC-4 and RAI T10 Interrupt.This bit is one when the corresponding latched status bit (RCRC0L, register address Y24) is set, and the corresponding mask bit is unmasked (RCRC0M, register address Y44). This bit is cleared when either this register, or the latched status register is read. Remote CRC-4 and RAI T450 Interrupt. This bit is one when the corresponding latched status bit (RCRC1L, register address Y24) is set, and the corresponding mask bit is unmasked (RCRC1M, register address Y44). This bit is cleared when either this register, or the latched status register is read.
13
RSLPI
12
YI
11
AUXPI
10
RAII
9
AISI
8
AIS16I
7
LOSSI
6
RCRC0I
5
RCRC1I
Table 178 - Sync, CRC-4 Remote, Alarms, MAS and Phase Interrupt Status Register (Address Y34) (E1)
SEMICMF.019
189
MT9072
Bit 4 Name CEFSI Functional Description
Data Sheet
Consecutively Errored Frame Alignment Signal Interrupt. This bit is one when the corresponding latched status bit (CEFSL, register address Y24) is set, and the corresponding mask bit is unmasked (CEFSM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Remote CRC-4 Multiframe Generator/Detector Failure Interrupt. This bit is one when the corresponding latched status bit (RFAILL, register address Y24) is set, and the corresponding mask bit is unmasked (RFAILM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Receive CRC-4 Synchronization Interrupt. This bit is one when the corresponding latched status bit (CSYNCL, register address Y24) is set, and the corresponding mask bit is unmasked (CSYNCM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Receive Multiframe Alignment Interrupt. This bit is one when the corresponding latched status bit (MSYNCL, register address Y24) is set, and the corresponding mask bit is unmasked (MSYNCM, register address Y44). This bit is cleared when either this register, or the latched status register is read. Receive Basic Frame Alignment Interrupt. This bit is one when the corresponding latched status bit (BSYNCL, register address Y24) is set, and the corresponding mask bit is unmasked (BSYNCM, register address Y44). This bit is cleared when either this register, or the latched status register is read.
3
RFAILI
2
CSYNCI
1
MSYNCI
0
BSYNCI
Table 178 - Sync, CRC-4 Remote, Alarms, MAS and Phase Interrupt Status Register (Address Y34) (E1)
Bit 15 14
Name # SLOI not used.
Functional Description
Loss of Sync Counter Overflow Interrupt. This bit is one when the corresponding latched status bit (SLOL, register address Y25) is set, and the corresponding mask bit is unmasked (SLOM, register address Y45). This bit is cleared when either this register, or the latched status register is read. Frame Alignment Signal (FAS) Error Counter Overflow Interrupt. This bit is one when the corresponding latched status bit (FEOL, register address Y25) is set, and the corresponding mask bit is unmasked (FEOM, register address Y45). This bit is cleared when either this register, or the latched status register is read. Frame Alignment Signal (FAS) Error Counter Indication Interrupt. This bit is one when the corresponding latched status bit (FEIL, register address Y25) is set, and the corresponding mask bit is unmasked (FEIM, register address Y45). This bit is cleared when either this register, or the latched status register is read. Frame Alignment Signal (FAS) Bit Error Counter Overflow Interrupt. This bit is one when the corresponding latched status bit (BEOL, register address Y25) is set, and the corresponding mask bit is unmasked (BEOM, register address Y45). This bit is cleared when either this register, or the latched status register is read.
13
FEOI
12
FEII
11
BEOI
Table 179 - Counter Indication and Counter Overflow Interrupt Status Register (Address Y35) (E1)
190
SEMICMF.019
Data Sheet
Bit 10 Name BEII Functional Description
MT9072
Frame Alignment Signal (FAS) Bit Error Counter Indication Interrupt. This bit is one when the corresponding latched status bit (BEIL, register address Y25) is set, and the corresponding mask bit is unmasked (BEIM, register address Y45). This bit is cleared when either this register, or the latched status register is read. CRC-4 Error Counter Overflow Interrupt. This bit is one when the corresponding latched status bit (CEOL, register address Y25) is set, and the corresponding mask bit is unmasked (CEOM, register address Y45). This bit is cleared when either this register, or the latched status register is read. CRC-4 Error Counter Indication Interrupt. This bit is one when the corresponding latched status bit (CEIL, register address Y25) is set, and the corresponding mask bit is unmasked (CEIM, register address Y45). This bit is cleared when either this register, or the latched status register is read. Bipolar Violation (BPV) Error Counter Overflow Interrupt. This bit is one when the corresponding latched status bit (VEOL, register address Y25) is set, and the corresponding mask bit is unmasked (VEOM, register address Y45). This bit is cleared when either this register, or the latched status register is read. Bipolar Violation (BPV) Error Counter Indication Interrupt. This bit is one when the corresponding latched status bit (VEIL, register address Y25) is set, and the corresponding mask bit is unmasked (VEIM, register address Y45). This bit is cleared when either this register, or the latched status register is read. E-Bit Error Counter Overflow Interrupt. This bit is one when the corresponding latched status bit (EEOL, register address Y25) is set, and the corresponding mask bit is unmasked (EEOM, register address Y45). This bit is cleared when either this register, or the latched status register is read. E-Bit Error Counter Indication Interrupt. This bit is one when the corresponding latched status bit (EEIL, register address Y25) is set, and the corresponding mask bit is unmasked (EEIM, register address Y45). This bit is cleared when either this register, or the latched status register is read. PRBS CRC-4 Counter Overflow Interrupt. This bit is one when the corresponding latched status bit (PCOL, register address Y25) is set, and the corresponding mask bit is unmasked (PCOM, register address Y45). This bit is cleared when either this register, or the latched status register is read. not used. PRBS Error Counter Overflow Interrupt. This bit is one when the corresponding latched status bit (PEOL, register address Y25) is set, and the corresponding mask bit is unmasked (PEOM, register address Y45). This bit is cleared when either this register, or the latched status register is read. PRBS Error Counter Indication Interrupt. This bit is one when the corresponding latched status bit (PEIL, register address Y25) is set, and the corresponding mask bit is unmasked (PEIM, register address Y45). This bit is cleared when either this register, or the latched status register is read.
9
CEOI
8
CEII
7
VEOI
6
VEII
5
EEOI
4
EEII
3
PCOI
2 1
# PEOI
0
PEII
Table 179 - Counter Indication and Counter Overflow Interrupt Status Register (Address Y35) (E1)
SEMICMF.019
191
MT9072
Bit 15 14 Name # Sa5VI not used. Functional Description
Data Sheet
Sa5 Value Bit Interrupt. This bit is one when the corresponding latched status bit (Sa5VL, register address Y26) is set, and the corresponding mask bit is unmasked (Sa5VM, register address Y46). This bit is cleared when either this register, or the latched status register is read. Sa6 Value Bits 3-0 Interrupt. This bit is one when the corresponding latched status bit (Sa6V*L, register address Y26) is set, and the corresponding mask bit is unmasked (Sa6V*M, register address Y46). This bit is cleared when either this register, or the latched status register is read. Eight Consecutive Sa6 Nibbles Interrupt. This bit is one when the corresponding latched status bit (Sa6N8L, register address Y26) is set, and the corresponding mask bit is unmasked (Sa6N8M, register address Y46). This bit is cleared when either this register, or the latched status register is read. Sa6 Nibble Change Interrupt. This bit is one when the corresponding latched status bit (Sa6NL, register address Y26) is set, and the corresponding mask bit is unmasked (Sa6NM, register address Y46). This bit is cleared when either this register, or the latched status register is read. Sa Nibble Change Interrupt. This bit is one when the corresponding latched status bit (SaNL, register address Y26) is set, and the corresponding mask bit is unmasked (SaNM, register address Y46). This bit is cleared when either this register, or the latched status register is read. Sa5 Bit Change Interrupt. This bit is one when the corresponding latched status bit (Sa5TL, register address Y26) is set, and the corresponding mask bit is unmasked (Sa5TM, register address Y46). This bit is cleared when either this register, or the latched status register is read. Sa Bit Change Interrupt. This bit is one when the corresponding latched status bit (SaTL, register address Y26) is set, and the corresponding mask bit is unmasked (SaTM, register address Y46). This bit is cleared when either this register, or the latched status register is read. Receive Channel Associated Signaling (CAS) Interrupt. is bit is one when the corresponding latched status bit (CASRL, register address Y24) is set, and the corresponding mask bit is unmasked (CASRM, register address Y44). This bit is cleared when either this register, or the latched status register is read. CRC-4 Alignment 2ms Timer Interrupt. This bit is one when the corresponding latched status bit (CALNL, register address Y26) is set, and the corresponding mask bit is unmasked (CALNM, register address Y46). This bit is cleared when either this register, or the latched status register is read. Timer 2 Interrupt. This bit is one when the corresponding latched status bit (T2L, register address Y26) is set, and the corresponding mask bit is unmasked (T2M, register address Y46). This bit is cleared when either this register, or the latched status register is read. Timer 1 Interrupt. This bit is one when the corresponding latched status bit (T1L, register address Y26) is set, and the corresponding mask bit is unmasked (T1M, register address Y46). This bit is cleared when either this register, or the latched status register is read.
13 12 11 10 9
Sa6V3I Sa6V2I Sa6V1I Sa6V0I Sa6N8I
8
Sa6NI
7
SaNI
6
Sa5TI
5
SaTI
4
CASRI
3
CALNI
2
T2I
1
T1I
0
ONESECI One Second Timer Status Interrupt. This bit is one when the corresponding latched status bit (ONESECL, register address Y26) is set, and the corresponding mask bit is unmasked (ONESECM, register address Y46). This bit is cleared when either this register, or the latched status register is read.
Table 180 - CAS, National, CRC-4 Local and Timer Interrupt Status Register (Address Y36) (E1)
192
SEMICMF.019
Data Sheet
MT9072
16.2.6
Interrupt Vector Mask and Interrupt Mask Registers (Y4X) Bit Functions
Tables 125 and 126 describe the bit functions of the Interrupt Vector Masks, while tables 186 to 189 describe the bit functions of each of the Interrupt Mask Registers in the MT9072. Each interrupt mask register is repeated for each of the 8 framers (not the Interrupt Vector Masks). Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11A8). In addition, a simultaneous write to all 8 framers is possible by setting the MSB address to Y=8 (1000). However, since the Interrupt Vector Masks are common to all eight framers, only addresses 902 and 903 may be used to read from or write to these registers.
A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a reset (RESET, RSTC or RST). The (#) indicates that a (0) or (1) is possible.
Bit 15-9 8 7 6
Name # GAIM (0) EOPDIM (0) TEOPIM (0) EOPRIM (0) TXFLIM (0) FAIM (0) not used.
Functional Description
GAIM When unmasked an interrupt is generated when go-ahead pattern (01111111) was detected by the HDLC receiver. End of Packet Data Interrupt Mask.When unmasked an interrupt is initiated when an end of packet (EOP) byte was written into the RX FIFO by the HDLC receiver. Transmit End of Packet Interrupt Mask.When unmasked an interrupt is initiated when the byte about to be read from the RX FIFO is the last byte of the packet. An interrupt is also initiated if the Rx FIFO is read and there is no data in it. End of Packet Received Interrupt Mask.When unmasked an interrupt is initiated when the byte about to be read from the RX FIFO is the last byte of the packet. An interrupt is also initiated if the Rx FIFO is read and there is no data in it. Transmit Fifo Low Interrupt Mask.When unmasked an interrupt is initiated when the Tx FIFO is emptied below the selected low threshold level. Transmit Elastic Buffer full interrupt Mask. When unmasked an interrupt is initiated whenever the transmit elastic buffer is full.If 1 - masked, 0 - unmasked.
5
4 3 2 1 0
TXUNDERIM Transmit Fifo Underrun Interrupt Mask. interrupt is initiated for TX FIFO underrun (0) indication. RXFFIM (0) RXOVFLIM (0) Receive Fifo full Threshold interrupt Mask. When unmasked an interrupt is initiated whenever the Rx FIFO is filled above the selected full threshold level. Receive Fifo Overflow Interrupt Mask. When unmasked an interrupt is initiated whenever the 16 byte RX FIFO overflowed (i.e. an attempt to write to a 16 byte full RX FIFO).
Table 181 - HDLC Interrupt Mask Register (Address Y43) (E1)
SEMICMF.019
193
MT9072
Bit 15 14 Name # not used. Functional Description
Data Sheet
RCRCRM Remote CRC-4 and RAI Mask. This is the mask bit for the RCRCRI interrupt status bit in the (0) Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. RSLPM (0) Receive Slip Mask. This is the mask bit for the RSLPI interrupt status bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Receive Y-bit Mask. This is the mask bit for the YI interrupt status bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Auxiliary Pattern Mask. This is the mask bit for the AUXPI interrupt status bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Remote Alarm Indication Status Mask. This is the mask bit for the RAII interrupt status bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Alarm Indication Status Signal Mask. This is the mask bit for the AISI interrupt status bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Alarm Indication Signal 16 Status Mask. This is the mask bit for the AIS16I interrupt status bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Loss of Signal Status Indication Mask. This is the mask bit for the LOSSI interrupt status bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally.
13
12
YM (0)
11
AUXPM (0)
10
RAIM (0)
9
AISM (0)
8
AIS16M (0)
7
LOSSM (0)
6
RCRC0M Remote CRC-4 and RAI T10 Mask. This is the mask bit for the RCRC0I interrupt status bit in (0) the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. RCRC1M Remote CRC-4 and RAI T450 Mask. This is the mask bit for the RCRC1I interrupt status bit (0) in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally.
5
Table 182 - Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Mask Register (Address Y44) (E1)
194
SEMICMF.019
Data Sheet
Bit 4 Name CEFSM (0) Functional Description
MT9072
Consecutively Errored Frame Alignment Signal Mask. This is the mask bit for the CEFSI interrupt status bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Remote CRC-4 Multiframe Generator/Detector Failure Mask. This is the mask bit for the RFAILI interrupt status bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally.
3
RFAILM (0)
2
CSYNCM Receive CRC-4 Synchronization Mask. This is the mask bit for the CSYNCI interrupt status (0) bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. MSYNCM Receive Multiframe Alignment Mask. This is the mask bit for the MSYNCI interrupt status (0) bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. BSYNCM Receive Basic Frame Alignment Mask. This is the mask bit for the BSYNCI interrupt status (0) bit in the Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Status Register (address Y34). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally.
1
0
Table 182 - Sync (Sync, CRC-4 Remote, Alarms, MAS and Phase) Interrupt Mask Register (Address Y44) (E1) Bit 15 14 Name # SLOM (0) not used. Loss of Sync Counter Overflow Mask. This is the mask bit for the SLOI interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Frame Alignment Signal (FAS) Error Counter Overflow Mask. This is the mask bit for the FEOI interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Frame Alignment Signal (FAS) Error Counter Indication Mask. This is the mask bit for the FEII interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Frame Alignment Signal (FAS) Bit Error Counter Overflow Mask. This is the mask bit for the BEOI interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Functional Description
13
FEOM (0)
12
FEIM (0)
11
BEOM (0)
Table 183 - Counter (Counter Indication and Counter Overflow) Interrupt Mask Register (Address Y45) (E1)
SEMICMF.019
195
MT9072
Bit 10 Name BEIM (0) Functional Description
Data Sheet
Frame Alignment Signal (FAS) Bit Error Counter Indication Mask. This is the mask bit for the BEII interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. CRC-4 Error Counter Overflow Mask. This is the mask bit for the CEOI interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. CRC-4 Error Counter Indication Mask. This is the mask bit for the CEII interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Bipolar Violation (BPV) Error Counter Overflow Mask. This is the mask bit for the VEOI interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Bipolar Violation (BPV) Error Counter Indication Mask. This is the mask bit for the VEII interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. E-Bit Error Counter Overflow Mask. This is the mask bit for the EEOI interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. E-Bit Error Counter Indication Mask. This is the mask bit for the EEII interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. PRBS CRC-4 Counter Overflow Mask. This is the mask bit for the PCOI interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. not used. PRBS Error Counter Overflow Mask. This is the mask bit for the PEOI interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. PRBS Error Counter Indication Mask. This is the mask bit for the PEII interrupt status bit in the Counter (Counter Indication and Counter Overflow) Interrupt Status Register (address Y35). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally.
9
CEOM (0)
8
CEIM (0)
7
VEOM (0)
6
VEIM (0)
5
EEOM (0)
4
EEIM (0)
3
PCOM (0)
2 1
(0) PEOM (0)
0
PEIM (0)
Table 183 - Counter (Counter Indication and Counter Overflow) Interrupt Mask Register (Address Y45) (E1)
196
SEMICMF.019
Data Sheet
Bit 15 14 Name # Sa5VM not used. Functional Description
MT9072
Sa5 Value Bit Mask. This is the mask bit for the Sa5VI interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Sa6 Value Bits 3-0 Mask. This is the mask bit for the Sa6V*I interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. not used. Eight Consecutive Sa6 Nibbles Mask. This is the mask bit for the Sa6N8I interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Sa6 Nibble Change Mask. This is the mask bit for the Sa6NI interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Sa Nibble Change Mask. This is the mask bit for the SaNI interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Sa5 Bit Change Mask. This is the mask bit for the Sa5TI interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Sa Bit Change Mask. This is the mask bit for the SaTI interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Receive Channel Associated Signaling (CAS) Mask. This is the mask bit for the CASRI interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. CRC-4 Alignment 2ms Timer Mask. This is the mask bit for the CALNI interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally. Timer 2 Mask. This is the mask bit for the T2I interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally.
13 13 12 11 10 9
Sa6V3M Sa6V2M Sa6V1M Sa6V0M (0000) # Sa6N8M (0)
8
Sa6NM (0)
7
SaNM (0)
6
Sa5TM (0)
5
SaTM (0)
4
CASRM (0)
3
CALNM (0)
2
T2M (0)
Table 184 - National (CAS, National, CRC-4 Local and Timers) Interrupt Mask Register (Address Y46) (E1)
SEMICMF.019
197
MT9072
Bit 1 Name T1M (0) Functional Description
Data Sheet
Timer 1 Mask. This is the mask bit for the T1I interrupt status bit in the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally.
0
ONESECM One Second Timer Status Mask. This is the mask bit for the ONESECI interrupt status bit in (0) the National (CAS, National, CRC-4 Local and Timers) Interrupt Status Register (address Y36). If this mask bit is one, the corresponding interrupt bit will remain inactive. If this mask bit is zero, the corresponding interrupt bit will function normally.
Table 184 - National (CAS, National, CRC-4 Local and Timers) Interrupt Mask Register (Address Y46) (E1)
16.2.7
Transmit CAS (ABCD) Data Registers (Y51 - Y6F) Bit Functions
Table 190 describes the bit functions of each (30 registers in total, one register for each PCM 30 channel) of the Transmit CAS Data Registers in the MT9072. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11-A8). In addition, a simultaneous write to all 8 framers is possible by setting the MSB address to Y=8 (1000). Note that if corresponding MPST bit in the per timeslot control is not set this memory will be constantly updated with CSTi values. Hence to use this registers for any channels the corresponding MPST bit has to be set. A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a reset (RESET, RSTC or RST). The (#) indicates that a (0) or (1) is possible.
Bit 15-4 3 2 1 0
Name (#### #### ####) A(n) (#) B(n) (#) C(n) (#) D(n) (#) not used.
Functional Description
Transmit Channel Associated Signaling (CAS) Signaling Bits for Channel 1 to 30. Bits for n=1 to 15 correspond to channel 1 to 15 and are transmitted on the PCM30 link in timeslot 16 in bit positions one to four in frame n. Bits for n=17 to 31 correspond to channel 16 to 30 and are transmitted on the PCM30 link in timeslot 16 in bit positions five to eight in frame n -16. The corresponding CASS(n) bit must be one for this to function.
For these functions to be valid, CAS mode must be selected (CSIG=0 register address Y03), and the timeslot control must be selected (CASS(n)=1 register address Y90 to YAF). Table 185 - Channel n, Transmit CAS Data Register (Address Y51-Y6F) (E1)
198
SEMICMF.019
Data Sheet
16.2.8 Receive CAS (ABCD) Data Registers (Y71 - Y8F) Bit Functions
MT9072
Table 191 describes the bit functions of each (30 registers in total, one register for each PCM 30 channel) of the Receive CAS Data Registers in the MT9072. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11-A8). A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a reset (RESET, RSTC or RST). The (#) indicates that a (0) or (1) is possible.
Bit 15-4 3 2 1 0
Name (#### #### ####) A(n) (#) B(n) (#) C(n) (#) D(n) (#) not used.
Functional Description
Receive Channel Associated Signaling (CAS) Signaling Bits for Channel 1 to 30. Bits for n=1 to 15 correspond to channel 1 to 15 and are received on the PCM30 link in timeslot 16 in bit positions one to four in frame n. Bits for n=17 to 31 correspond to channel 16 to 30 and are received on the PCM30 link in timeslot 16 in bit positions five to eight in frame n -16.
For these functions to be valid, CAS mode must be selected (CSIG=0 register address Y03). Table 186 - Channel n, Receive CAS Data Register (Address Y71-Y8F)
16.2.9
Timeslot 0-31 Control Registers (Y90 - YAF) Bit Functions
Table 191 describes the bit functions of each (32 registers in total, one register for each timeslot) of the Timeslot Control Registers in the MT9072. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11-A8). In addition, a simultaneous write to all 8 framers is possible by setting the MSB address to Y=8 (1000). Note that timeslots 0 to 15 are accommodated by addresses Y90 to Y9F respectively, and timeslots 16 to 31 are accommodated by addresses YA0 to YAF respectively. A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a reset (RESET, RSTC or RST). The (#) indicates that a (0) or (1) is possible. Bit 15-10 9 Name (#### ####) not used. RADI(n) (0) MPDR (0) Receive Alternate Digit Inversion. the data received on DSTo timeslot n from the received PCM30 link timeslot n has every second bit inverted. If zero, this bit has no effect on channel data. Micro Port Data Receive. Setting this bit freezes the receive data for a given channel After putting the freeze the data (Y09). Functional Description
8
Table 187 - Timeslot (TS) n (n = 0 to 31) Control Register (Address Y90 (TS0) to YAF(TS31)) (E1)
SEMICMF.019
199
MT9072
Bit 7 Name CASS(n) (0) Functional Description
Data Sheet
Channel Associated Signaling (CAS) Source. Selects the source for the CAS data (A,B,C,D) on the transmit PCM30 link in bit positions one to four, and five to eight of timeslot 16 in frames 1 to 15. If zero, ST-BUS (CSTi) is selected as the source. If one, data register (register address Y5,6n) is selected as the source. For n=1 to 15, the CASS(n) bit corresponds to timeslot n which corresponds to channel n. For n=17 to 31, the CASS(n) bit corresponds to timeslot n which corresponds to channel n-1. Transmit Alternate Digit Inversion. If one, the data sourced from DSTi timeslot n (n = 0 to 31) to the transmit PCM30 link timeslot n has every second bit inverted, If zero, this bit has no effect on channel data. Remote Timeslot Loopback. If one, the data from the received PCM30 link timeslot n (n = 0 to 31) is output on DSTo timeslot n and is also looped back to the transmit PCM30 link timeslot n. If zero, the loopback is disabled. Local Timeslot Loopback. If one, the data sourced from DSTi timeslot n (n = 0 to 31) to the transmit PCM30 link timeslot n is also looped back to DSTo timeslot n. If zero, this loopback is disabled. Transmit Test. If one and control bit ADSEQ (register address Y01) is one, the A-law digital milliwatt will be transmitted in PCM30 timeslot n. When one and ADSEQ is zero, a Pseudo-Random Bit Sequence (PRBS 215-1) will be transmitted in PCM30 timeslot n. More than one timeslot may be activated at once. If zero, neither of these test signals will be connected to timeslot n. Receive Test. If one and control bit ADSEQ (register address Y01) is one, the A-law digital milliwatt will be transmitted in DSTo timeslot n. When one and ADSEQ is zero, a Pseudo Random Bit Sequence (PRBS 215-1) receiver will be connected to DSTo timeslot n. This receiver circuit will synchronize to the transmit PRBS signal and perform a bit comparison of the two sequences. If zero, neither of these test signals will be connected to the corresponding timeslot. Micro Port Data Transmit. Setting this bit allows for the transmit data for a given channel to be replaced by the idle code(Y0A). The idle code can be written by the micro port for trunck conditioning applications. The data in Y0A will replace the appropriate PCM30 channel. not used.
6
TADI(n) (0) RTSL(n) (0) LTSL(n) (0) TTST(n) (0)
5
4
3
2
RRST(n) (0)
1
MPDT(0)
0
(#)
Note: For address Y90 (n=0), set all control bits to 0.
Table 187 - Timeslot (TS) n (n = 0 to 31) Control Register (Address Y90 (TS0) to YAF(TS31)) (E1)
16.2.10
Transmit National Bit RN Data Registers (YB0- YB4) Bit Functions
Table 192 describes the bit functions of each (5 registers in total, one register for each bit position) of the Transmit National Bits Data Registers in the MT9072. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11-A8). In addition, a simultaneous write to all 8 framers is possible by setting the MSB address to Y=8 (1000). Each register contains one byte (8-bits) of data corresponding to eight frames of a particular bit position in timeslot 0. There are 5 registers in total containing 5 bytes of data, occupying addresses YB0 to YB4. Address YB0 corresponds to bit position 4 (TN0=Sa4) and address YC4 corresponding to bit position 8 (TN4=Sa8).
A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a reset (RESET, RSTC or RST). The (#) indicates that a (0) or (1) is possible.
200
SEMICMF.019
Data Sheet
Bit 15-8 7 6 5 4 3 2 1 0 Name (#### ####) TNnF1 TNnF3 TNnF5 TNnF7 TNnF9 TNnF11 TNnF13 TNnF15 (0000 0000) not used. Functional Description
MT9072
Transmit National Bit TNnFm (n = 0 to 4, m = 1, 3, 5 etc. to 15). This bit is transmitted on the PCM30 link, in bit position n+4 of Timeslot 0 during Frame m (non-frame alignment signal (NFAS) frames) when CRC-4 multiframe alignment is used, or of consecutive odd frames when CRC-4 multiframe alignment is not used. Bit TNnFm is sourced from register address YFn as follows. TN0Fm = Address YF8 corresponds to transmit national bits Sa4Fm TN1Fm = Address YF9 corresponds to transmit national bits Sa5Fm TN2Fm = Address YFA corresponds to transmit national bits Sa6Fm TN3Fm = Address YFB corresponds to transmit national bits Sa7Fm TN4Fm = Address YFC corresponds to transmit national bits Sa8Fm
Table 188 - Transmit National Bits (Sa4 - Sa8) TNn (n = 0 to 4) Data Register (R/W Address YB0 to YB4) (E1)
16.2.11
Receive National Bit RN Data Registers (YC0- YC4) Bit Functions
Table 193 describes the bit functions of each (5 registers in total, one register for each bit position) of the Receive National Bits Data Registers in the MT9072. Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11-A8). Each register contains one byte (8-bits) of data corresponding to eight frames of a particular bit position in timeslot 0. There are 5 registers in total containing 5 bytes of data, occupying addresses YC0 to YC4 Address YC0 corresponds to bit position 4 (RN0=Sa4) and address YC4 corresponding to bit position 8 (RN4=Sa8). A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a reset (RESET, RSTC or RST). The (#) indicates that a (0) or (1) is possible.
Bit 15-8 7 6 5 4 3 2 1 0
Name (#### ####) RNnF1 RNnF3 RNnF5 RNnF7 RNnF9 RNnF11 RNnF13 RNnF15 (0000 0000) not used.
Functional Description
Receive National Bit RNnFm (n = 0 to 4, m = 1, 3, 5 etc. to 15). This bit is received from the PCM30 link, in bit position n+4 of Timeslot 0 during Frame m (non-frame alignment signal (NFAS) frames) when CRC-4 multiframe alignment is used, or of consecutive odd frames when CRC-4 multiframe alignment is not used. Bit RNnFm is sourced to register address YCn as follows. RN0Fm = Address YC0 corresponds to receive national bit Sa4Fm RN1Fm = Address YC1 corresponds to receive national bit Sa5Fm RN2Fm = Address YC2 corresponds to receive national bit Sa6Fm RN3Fm = Address YC3 corresponds to receive national bit Sa7Fm RN4Fm = Address YC4 corresponds to receive national bit Sa8Fm Table 189 - Receive National Bits (Sa4 - Sa8) RNn (n = 0 to 4) Data Register (R/W Address YC0 to YC4) (E1)
SEMICMF.019
201
MT9072
16.2.12 Master Control Registers (YF0 - YF6) Bit Functions
Data Sheet
Tables 194 to 197 describe the bit functions of each of the Master Control Registers in the MT9072 in E1 Mode(YF0 to YF6). Each register is repeated for each of the 8 framers. Framer 0 is addressed with Y=0, Framer 1 with Y=1, Framer 2 with Y=2 and so on up to Framer 7 with Y=7 (where Y represents the 4 most significant address bits (MSB) A11-A8). In addition, a simultaneous write to all 8 framers is possible by setting the MSB address to Y=8 (1000). A (0), (1) or (#) in the "Name" column of these tables indicates the state of the data bits after a reset (RESET, RSTC or RST). The (#) indicates that a (0) or (1) is possible. Bit 15-11 10 Name # ADREC (0) RXEN (0) not used. Address Recognition. When high, this bit will enable address recognition. This forces the receiver to recognize only those packets having the unique address as programmed in the Receive Address Recognition Registers or if the address is an All Call Address. Receive Enable. When low this bit will disable the HDLC receiver. The receiver will disable after the rest of the packet presently being received is finished. The receiver's internal clock is disabled. When high the receiver will be immediately enabled (depending on the state of RXCEN input) and will begin searching for flags, Go-aheads etc. Transmit Enable. When low this bit will disable the HDLC transmitter. The transmitter will disable after the completion of the packet presently being transmitted. The transmitter's internal clock is disabled. When high the transmitter will be immediately enabled (depending on the state of the TXCEN input) and will begin transmitting data, or go to a mark idle or interframe time fill state. End of Packet When set this bit will indicate an end of packet byte to the transmitter, which will transmit an FCS following this byte. This facilitates loading of multiple packets into TX FIFO. Reset automatically after a write to the TX FIFO occurs. Framer Abort.Forms a tag on the next byte written to the TX FIFO, and when set will indicate to the transmitter that it should abort the packet in which that byte is being transmitted. Reset automatically after a write to the TX FIFO. Mark-Idle.When low, the transmitter will be in an idle state. When high it is in an interframe time fill state. These two states will only occur when the TX FIFO is empty. Cycle.When high, this bit will cause the transmit byte count to cycle through the value loaded into the Transmit Byte Count Register. Transmit CRC Inhibit. When high, this bit will inhibit transmission of the CRC. That is, the transmitter will not insert the computed CRC onto the bit stream after seeing the EOP tag byte. This is used in V.120 terminal adaptation for synchronous protocol sensitive UI frames. Seven. When high, this bit will enable seven bits of address recognition in the first address byte. The received address byte must have bit 0 equal to 1 which indicates a single address byte is being received. Table 190 - HDLC Control1(YF2) (E1) Functional Description
9
8
TXEN (0)
7
EOP (0) FA (0) MI (0) CYCLE (0) TCRCI (0)
6
5 4 3
2
SEVEN (0)
202
SEMICMF.019
Data Sheet
Bit 1 Name RXFRST (0) TXFRST (0) Functional Description
MT9072
Rx Fifo Reset. When high, the RX FIFO will be reset. This causes the receiver to be disabled until the next reception of a flag. The status register will identify the FIFO as being empty. However, the actual bit values in the RX FIFO will not be reset. Transmit FIFO Reset. When high, the TX FIFO will be reset. The Status Register will identify the FIFO as being empty. This bit will be reset when data is written to the TX FIFO. However, the actual bit values of data in the TX FIFO will not be reset. Table 190 - HDLC Control1(YF2) (E1)
0
Bit 15-6 5
Name # HRST (0) not used.
Functional Description
HDLC Reset. When this bit is high, the HDLC and HDLC registers will be reset (HDLC Control, HDLC Test Control, Address Recognition Byte). This is similar to RESET being applied, the only difference being that this bit will not be reset. This bit can only be reset by writing a zero to this location or applying RESET. Receive Transmit Loopback. When this bit is high, receive to transmit HDLC loopback will be activated. Receive data, including end of packet indication, but not including flags or CRC, will be written to the TX FIFO as well as the RX FIFO. When the transmitter is enabled, this data will be transmitted as though written by the microprocessor. Both good and bad packets will be looped back. Receive to transmit loopback may also be accomplished by reading the RX FIFO using the microprocessor and writing these bytes, with appropriate tags, into the TX FIFO. CRC Test. This bit allows direct access to the CRC Comparison Register in the receiver through the serial interface. After testing is enabled, serial data is clocked in until the data aligns with the internal comparison (16 RXC clock cycles) and then the clock is stopped. The expected pattern is F0B8 hex. Each bit of the CRC can be corrupted to allow more efficient testing. Fifo Test. This bit allows the writing to the RX FIFO and reading of the TX FIFO through the microprocessor to allow more efficient testing of the FIFO status/interrupt functionality. This is done by making a TX FIFO write become a RX FIFO write and a RX FIFO read become a TX FIFO read. In addition, EOP/FA and RQ8/RQ9 are re-defined to be accessible (i.e. RX write causes EOP/FA to go to RX fifo input; TX read looks at output of TX fifo through RQ8/RQ9 bits). Address Recognition Test. This bit allows direct access to the Address Recognition Registers in the receiver through the serial interface to allow more efficient testing. After address testing is enabled, serial data is clocked in until the data aligns with the internal address comparison (16 RXc clock cycles) and then clock is stopped. Then the VADDR bit in Y1C can be checked. HDLC Loopback. When high, transmit to receive HDLC loopback will be activated. The packetized transmit data will be looped back to the receive input. RXEN and TXEN bits must also be enabled. Table 191 - HDLC Test Control(YF3) (E1)
4
RTLOOP (0)
3
CRCTST (0)
2
FTST (0)
1
ADTST (0)
0
HLOOP (0)
SEMICMF.019
203
MT9072
Bit 15-8 7-0 Name # BIT7-0 (00000000) not used. Functional Description
Data Sheet
This eight bit word is tagged with the two status bits from control register 1 (EOP and FA), and the resulting 10 bit word is written to the TX FIFO. The FIFO status is not changed immediately after a write or read occurs. It is updated after the data has settled and the transfer to the last available position has finished. Note that when the HDLC is connected to a T1 channel, the least significant bit in the FIFO is sent first. Table 192 - TX Fifo Write Register(YF5) (E1)
Bit 15-8 7-0
Name # CNT7-0 (00000000) not used.
Functional Description
The Transmit Byte Count Register indicating the length of the data portion of the packet about to be transmitted. This is the size of the data and not the address, flags or FCS. The Transmit Byte Counter position Y1C determines the number of bytes that have been sent from the Transmit FIFO. Table 193 - TX Byte Count Register(YF6) (E1)
16.2.13
Global Control and Status Registers(900-91F) Bit Functions
The Global Control and Status Registers are common to the T1 and E1 operation. The global registers are accessed by address hex 9xx ( A11 and A8 being high and A10 and A9 being low) Bit 15 Name T1E0 (1) Functional Description T1E0. This bit determines if the chip will operate in T1 or E1 mode for all 8 framers. If the value of this bit is changed the chip is reset in E1 or T1 default register mode. If the bit is set to 1, all the framer register values are set to T1 defaults. For a setting of 0 the register values are set to E1 defaults. This action takes approximately 34 1.5444 clock cycles. Hence any writes to registers should be done on the next 125 usec frame after setting or clearing this bit.
14 13-5 4
STBUS ST-BUS Enable. If zero, ST-BUS timing is enabled. If one, GCI timing is enabled (only available (0) for 2.048Mb/s mode). See Figures 24-31. # CK1 not used Clock Rate. These clock select bits determine the system clock at the CKi pin and the receive frame pulse at the FPi pin as follows (See Figures 24 to 31): Clock Frame Pulse System Bus CK1 0 4.096MHz 2.048Mb/s 2.048Mb/s 1 16.384MHz 8.192Mb/s 8.192Mb/s not used. Common Reset. When this bit is changed from zero to one, all eight framers will reset to their default T1 mode. This software reset has the same effect as the RESET pin. See the Reset Operation section for the default settings. Table 194 - Global Control0 Register (R/W Address 900) (E1)
3-1 0
# RSTC (0)
204
SEMICMF.019
Data Sheet
Bit Name Functional Description
MT9072
15-11 CHANNUM Channel Number. These 5 bits determine the channel that is used for updating of the ST(00000) BUS Analyzer buffer. 10-8 7-6 # STRNUM (00000) not used. Stream Number. These 5 bits determine the streams that will be used as the source data for the ST-BUS Analyzer buffer. 00: Dsti 01: DSTo 10: Csti 11: Csto ST-BUS Analyser Buffer Enable. Setting this bit enables the ST-BUS Analyser Buffer update. When the user reads the buffer(920-93F), this bit must be 0. Any reads of the buffer while this bit is set does not ensure correct data being read. Framer Number. 0 to 7. Channel Update. If 0 the update of the memory is at frame rate for a given channel. The channel selected for update is provided by the ChanNum bits of this register. If set the complete frame(channels 0 to 32) are updated to the buffer. Continuous Single. If set to 1 the ST-BUS Analyzer buffer is updated continuously. If set to zero the buffer is updated once and stopped. An optional interrupt can be generated once the buffer is full. Table 195 - Global Control1 Register (R/W Address 901) (E1) Bit 15 Name Functional Description
5
STBUFEN (0) FNUM (000) CHUP (0) CONTSIN (0)
4-2 1
0
F3HM Framer 3 HDLC Mask. This is the mask bit for the F3HVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F3EM Framer 3 Elastic Mask. This is the mask bit for the F3EVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F3RM Framer 3 Rx Line Mask. This is the mask bit for the F3RVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F3SM Framer 3 Sync and Overflow Mask. This is the mask bit for the F3SVS status bit in the Interrupt (0) Vector Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F2HM Framer 2 HDLC Mask. This is the mask bit for the F2HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. Table 196 - Interrupt Vector 1 Mask Register (R/W Address 902) (E1)
14
13
12
11
SEMICMF.019
205
MT9072
Bit 10 Name Functional Description
Data Sheet
F2EM Framer 2 Elastic Mask. This is the mask bit for the F2EVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F2RM Framer 2 Rx Line Mask. This is the mask bit for the F2RVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F2SM Framer 2 Sync and Overflow Mask. This is the mask bit for the F2SVS status bit in the Interrupt (0) Vector Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F1HM Framer 1 HDLC Mask. This is the mask bit for the F1HVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F1EM Framer 1 Elastic Mask. This is the mask bit for the F1EVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F1RM Framer 1 Rx Line Mask. This is the mask bit for the F1RVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F1SM Framer 1 Sync and Overflow Mask. This is the mask bit for the F1SVS status bit in the Interrupt (0) Vector Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F0HM Framer 0 HDLC Mask. This is the mask bit for the F0HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F0EM Framer 0 Elastic Mask. This is the mask bit for the F0EVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F0RM Framer 0 Rx Line Mask. This is the mask bit for the F0RVS status bit in the Interrupt Vector (0) Register(address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F0SM Framer 0 Sync and Overflow Mask. This is the mask bit for the F0SVS status bit in the Interrupt (0) Vector Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. Table 196 - Interrupt Vector 1 Mask Register (R/W Address 902) (E1)
9
8
7
6
5
4
3
2
1
0
206
SEMICMF.019
Data Sheet
Bit 15 Name Functional Description
MT9072
F7HM Framer 7 HDLC Mask. This is the mask bit for the F7HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F7EM Framer 7 Elastic Mask. This is the mask bit for the F7EVS status bit in the Interrupt Vector (0) Register(address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F7RM Framer 7 Rx Line Mask. This is the mask bit for the F7RVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F7SM Framer 7 Sync and Overflow Mask. This is the mask bit for the F7SVS status bit in the Interrupt (0) Vector Register(address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F6HM Framer 6 HDLC Mask. This is the mask bit for the F6HVS status bit in the Interrupt Vector Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F6EM Framer 6 Elastic Mask. This is the mask bit for the F6EVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F6RM Framer 6 Rx LineMask. This is the mask bit for the F6RVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F6SM Framer 6 Sync and Overflow Mask. This is the mask bit for the F6SVS status bit in the Interrupt (0) Vector Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F5HM Framer 5 HDLC Mask. This is the mask bit for the F5HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F5EM Framer 5 Elastic Mask. This is the mask bit for the F5EVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F5RM Framer 5 Rx Line Mask. This is the mask bit for the F5RVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. Table 197 - Interrupt Vector 2 Mask Register (R/W Address 903) (E1)
14
13
12
11
10
9
8
7
6
5
SEMICMF.019
207
MT9072
Bit 4 Name Functional Description
Data Sheet
F5SM Framer 5 Sync and Overflow Mask. This is the mask bit for the F5SVS status bit in the Interrupt (0) Vector Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F4HM Framer 4 HDLC Mask. This is the mask bit for the F5HVS status bit in the Interrupt Vector (0) Register (address 910). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F4EM Framer 4 Elastic Mask. This is the mask bit for the F4EVS status bit in the Interrupt Vector (0) Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F4RM Framer 4 Rx Line Mask. This is the mask bit for the F4RVS status bit in the Interrupt Vector (0) register(address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. F4SM Framer 4 Sync and Overflow Mask. This is the mask bit for the F4SVS status bit in the Interrupt (0) Vector Register (address 911). If this mask bit is one, the corresponding Interrupt Vector status bit will remain inactive (zero). If this mask bit is zero, the corresponding Interrupt Vector status bit will function normally. Table 197 - Interrupt Vector 2 Mask Register (R/W Address 903) (E1)
3
2
1
0
208
SEMICMF.019
Data Sheet
Bit 15 14 13 12 11 10 Name SLBK8 (0) Functional Description
MT9072
ST-BUS Loopback 8M All. If one, DSTo[0] is connected to DSTi[4], and DSTo[4] is connected to DSTi[0]. This can be used in 8.192 Mbit/s or 2.048 Mbit/s mode. See Loopbacks section.
SLBK67 ST-BUS Loopback Framer 6 & 7. If one, DSTo[6] is connected to DSTi[7], and DSTo[7] is (0) connected to DSTi[6]. Used only in 2.048Mb/s mode. See Loopback section for details. SLBK45 ST-BUS Loopback Framer 4 & 5. If one, DSTo[4] is connected to DSTi[5], and DSTo[5] is (0) connected to DSTi[4]. Used only in 2.048Mb/s mode. See Loopbacks section. SLBK23 ST-BUS Loopback Framer 2 & 3. If one, DSTo[2] is connected to DSTi[3], and DSTo[3] is (0) connected to DSTi[2]. Used only in 2.048Mb/s mode. See Loopbacks section. SLBK01 ST-BUS Loopback Framer 0 & 1. If one, DSTo[0] is connected to DSTi[1], and DSTo[1] is (0) connected to DSTi[0]. Used only in 2.048Mb/s mode. See Loopbacks section. RLBK8 (0) Remote Loopback 8 Framers. If one, TPOS[0]/TNEG[0] are connected to RPOS[4]/RNEG[4], and TPOS[4]/TNEG[4] are connected to RPOS[0]/RNEG[0]. This is used especially for 8.192 Mbit/s mode but may also be used in 2.048Mb/s mode. See Loopbacks section.
9
RLBK67 Remote Loopback Framer 6 & 7. If one, TPOS[6]/TNEG[6] are connected to (0) RPOS[7]/RNEG[7], and TPOS[7]/TNEG[7] are connected to RPOS[6]/RNEG[6]. Used only in 2.048Mb/s mode. See Loopbacks section. RLBK45 Remote Loopback Framer 4 & 5. If one, TPOS[4]/TNEG[4] are connected to (0) RPOS[5]/RNEG[5], and TPOS[5]/TNEG[5] are connected to RPOS[4]/RNEG[4]. Used only in 2.048Mb/s mode. See Loopbacks section. RLBK23 Remote Loopback Framer 2 & 3. If one, TPOS[2]/TNEG[2] are connected to (0) RPOS[3]/RNEG[3], and TPOS[3]/TNEG[3] are connected to RPOS[2]/RNEG[2]. Used only in 2.048Mb/s mode. See Loopbacks section. RLBK01 Remote Loopback Framer 0 & 1. If one, TPOS[0]/TNEG[0] are connected to (0) RPOS[1]/RNEG[1], and TPOS[1]/TNEG[1] are connected to RPOS[0]/RNEG[0]. Used only in 2.048Mb/s mode. See Loopbacks section. (000000) not used. Table 198 - Framer Loopback Global Register(904) (E1)
8
7
6
5-0
SEMICMF.019
209
MT9072
Bit 15 Name Functional Description
Data Sheet
F3HVS Framer 3 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(333) for framer are set. This bit can be masked and will remain low by the F3HM bit in address 902. F3EVS Framer 3 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(336) or Elastic store status for Framer 3 are set. This bit can be masked and will remain low by the F3EM bit in address 902. F3RVS Framer 3 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(335) for Framer 0 are set. This bit can be masked and will remain low by the F3RM bit in address 902. F3SVS Framer 3 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(334) for Framer 3 are set. This bit can be masked and will remain low by the F3SM bit in address 902. F2HVS Framer 2 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(233) or Elastic store status far Framer 2 are set. This bit can be masked and will remain low by the F2HM bit in address 902. F2EVS Framer 2 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elastic status register(236) or Elastic store status for Framer 2 are set. This bit can be masked and will remain low by the F2EM bit in address 902. F2RVS Framer 2 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(235) for Framer 2 are set. This bit can be masked and will remain low by the F2RM bit in address 902. F2SVS Framer 2 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Counter status register(234) for Framer 2 are set. This bit can be masked and will remain low by the F2SM bit in address 902. F1HVS Framer 1 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(133) or Elastic store status for Framer 1 are set. This bit can be masked and will remain low by the F2HM bit in address 902. F1EVS Framer 1 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(136) or Elastic store status for Framer 1 are set. This bit can be masked and will remain low by the F1EM bit in address 902. F1RVS Framer 1 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(135) for Framer 1 are set. This bit can be masked and will remain low by theF1RM bit in address 902. F1SVS Framer 1 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(134) for Framer 3 are set. This bit can be masked and will remain low by the F1SM bit in address 902. F0HVS Framer 0 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(033) or Elastic store status for Framer 0 are set. This bit can be masked and will remain low by the F0HM bit in address 902. F0EVS Framer 0 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(036) or Elastic store status for Framer 0 are set. This bit can be masked and will remain low by the F0EM bit in address 902. Table 199 - Interrupt Vector 1 Status Register (R/W Address 910) (E1)
14
13
12
11
10
9
8
7
6
5
4
3
2
210
SEMICMF.019
Data Sheet
Bit 1 Name Functional Description
MT9072
F0RVS Framer 0 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(035) for Framer 0 are set. This bit can be masked and will remain low by the F0RM bit in address 902. F0SVS Framer 0 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(034) for Framer 0 are set. This bit can be masked and will remain low by the F0SM bit in address 902. Table 199 - Interrupt Vector 1 Status Register (R/W Address 910) (E1)
0
Bit 15
Name
Functional Description
F7HVS Framer 3 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(733) for Framer 7 are set. This bit can be masked and will remain low by the F7HM bit in address 903. F7EVS Framer 7 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(736) or Elastic store status for Framer 7 are set. This bit can be masked and will remain low by the F7EM bit in address 903. F7RVS Framer 7 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(735) for Framer 7 are set. This bit can be masked and will remain low by the F7RM bit in address 903 . F7SVS Framer 7 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt HDLC (0) register(734) for Framer 3 are set. This bit can be masked and will remain low by the F7SM bit in address 903. F6HVS Framer 6 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(663) or Elastic store status for Framer 6 are set. This bit can be masked and will remain low by the F7HM bit in address 903. F6EVS Framer 6 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(636) or Elastic store status for Framer 5 are set. This bit can be masked and will remain low by the F5EM bit in address 903. F6RVS Framer 6 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(635) for Framer 6 are set. This bit can be masked and will remain low by the F6RM bit in address 903. F6SVS Framer 6 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Counter status register(634) for Framer 6 are set. This bit can be masked and will remain low by the F6SM bit in address 903. F5HVS Framer 3 HDLC Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) HDLC register(533) or Elastic store status for Framer 5 are set. This bit can be masked and will remain low by the F7HM bit in address 903. F5EVS Framer 5 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(536) or Elastic store status for Framer 5 are set. This bit can be masked and will remain low by the F5EM bit in address 903. Table 200 - Interrupt Vector 2 Status Register (Address 911) (E1)
14
13
12
11
10
9
8
7
6
SEMICMF.019
211
MT9072
Bit 5 Name Functional Description
Data Sheet
F5RVS Framer 5 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(535) are Framer 5 are set. This bit can be masked and will remain low by theF1RM bit in address 903. F5SVS Framer 5 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(534) for Framer 5 are set. This bit can be masked and will remain low by the F1SM bit in address 903. F4HVS Framer 4 HDLC Vector Status. This bit if unmasked is set if any of the bits in the HDLC status (0) register(433)status for Framer 4 are set. This bit can be masked and will remain low by the F7HM bit in address 903. F4EVS Framer 4 Elastic Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Elasitc store register(436) or Elastic store status for Framer 4 are set. This bit can be masked and will remain low by the F4EM bit in address 903. F4RVS Framer 4 Rx Line Vector Status. This bit if unmasked is set if any of the bits in the Interrupt (0) Receive Line status register(435) for Framer 4 are set. This bit can be masked and will remain low by the F4RM bit in address 903. F4SVS Framer 4 Sync Vector Status. This bit if unmasked is set if any of the bits in the Interrupt Sync (0) status register(434) Framer 4 are set. This bit can be masked and will remain low by the F4SM bit in address 903. Table 200 - Interrupt Vector 2 Status Register (Address 911) (E1)
4
3
2
1
0
Bit 15-3 2 1 0
Name ID15-3 ID2-0 (000)
Functional Description ID Number. Contains 0100000001011. These 3 bits make up a binary code which identify the revision of this deviceID Number.
Table 201 - Identification Revision Code Data Register (R Address 912) (E1) Bit 15-1 0 Name # STIS (0) not used. ST-BUS Analyser Interrupt Status. This bit is set if the ST-BUS Analyser is filled up. Functional Description
Table 202 - ST-BUS Analyzer Vector Status Register (Address 913) (E1) Bit 15-8 7-0 Name # not used. Functional Description
STAD ST-BUS Analyser Data. This is the data for the ST-BUS analyser buffer. 920 is the first byte of (7-0) the data that is being "analyzed". The source of the data can be any ST-BUS stream from any (0) Framer. Table 203 - ST-BUS Analyser Data (Address 920-93F) (E1)
212
SEMICMF.019
Data Sheet
17.0
17.1
MT9072
Applications
T1 Applications
LIU 1/8 Receive xfmr LINE 1 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 1/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo CSTo
HDLC Timing
F0 C2
DSTi CSTi CKi FPi
RCLK, TCLK TSP RSP 1
LIU's 2 to 7
Framers 2 to 7
DSTo CSTo 6 1
HDLC
RCLK TCLK RDATA TDATA RSP TSP SCLK
LINES 2 to 7
DSTi CSTi CKi FPi 6
LIU 8/8 Receive xfmr LINE 8 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo CSTo
DSTi CSTi CKi FPi
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, * of Generic LIU PLL, 1 of MT9044 HDLC, 1 of PEB 20320 (MUNICH 32)
PLL From RCLK's of LIU's
PRI SEC F0o C2o C4o C16o RCLK RSP TSP
- Framer elastic buffer is used. - LIU Transmit JA and PLL are bypassed.
Figure 11 - 8 T1 Links with Synchronous Common Channel Signaling for up to 24 Channels
SEMICMF.019
213
MT9072
LIU 1/8 Receive xfmr LINE 1 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Data Sheet
Framer 1/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo TxDL TxDLC
HDLC 1/8
CDSTi RxCEN CDSTo TxCEN CKi
CKi FPi
LIU's 2 to 7
Framers 2 to 7
DSTo
6 6 6
HDLC 2 to 7
CDSTi RxCEN CDSTo TxCEN CKi
LINES 2 to 7
TxDL TxDLC
CKi FPi
LIU 8/8 Receive xfmr LINE 8 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo TxDL TxDLC
HDLC 8/8
CDSTi RxCEN CDSTo TxCEN CKi
CKi FPi
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 8 of Generic LIU's PLL, 1 of MT9042 HDLC, 8 of MT8952 PLL
From RCLK's of LIU's PRI SEC F0o C2o C4o
- Framer elastic buffer is used. - Data Link data passes through the elastic buffer. - TxDLC outputs an enable signal - LIU Transmit JA and PLL are bypassed. - The MT8952B is in External Timing mode.
Figure 12 - 8 T1 Links with Synchronous Data Link Signaling
214
SEMICMF.019
Data Sheet
MT9072
LIU 1/8 Receive xfmr
RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 1/8
RPOS RNEG EXCLi TPOS TNEG TXCL RxDL RxDLC TxDL TxDLC
HDLC 1/16
CDSTi RxCEN CDSTo TxCEN CKi
LINE 1 Transmit xfmr
TT TR
CKi FPi
HDLC 2/16
CDSTi RxCEN CDSTo TxCEN CKi
6
LIU's 2 to 7
Framers 2 to 7
RxDL RxDLC TxDL TxDLC
LINES 2 to 7
RCLK
6 6 6 6
HDLC 3-15 odd CDSTi RxCEN CDSTo TxCEN CKi
CKi FPi
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 8 of Generic LIU PLL, 1 of MT9042 HDLC, 8 of MT8952 PLL From RCLK's of LIU's
PRI SEC F0o C2o C4o
HDLC 4-16 even CDSTi RxCEN CDSTo TxCEN CKi
- Framer elastic buffer is used. - Data Link data passes through the elastic buffer. - TxDLC & RXDLC outputs an enable signal - LIU Transmit JA and PLL are bypassed. - The MT8952B is in External Timing mode.
Figure 13 - 8 T1 Links with Asynchronous Data Link Signaling
SEMICMF.019
215
MT9072
LIU 1/8 Receive xfmr LINE 1 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Data Sheet
Framer 1/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo CSTo RXDLC DSTi CSTi CKi FPi STi0
LDX
STo0
LIU's 2 to 7
Framers 2 to 7
DSTo CSTo
7 STi1-6
LINES 2 to 7
DSTi CSTi CKi FPi 7 STo1-6
LIU 8/8 Receive xfmr LINE 8 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo CSTo STi7
DSTi CSTi CKi FPi
STo7
STi8-15 STo8-15
PLL Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 8 of Generic LIU PLL, 1 of MT9042 LDX, 1 of MT90820 - Framer elastic buffer is used. - LIU Transmit JA and PLL are bypassed. From RCLK's
of LIU's PRI SEC F0o C2o C4o F0i C4i
Figure 14 - 8 T1 Links with no JA or PLL in LIU, Slave or Master Mode, Jitter-Free ST-BUS
216
SEMICMF.019
Data Sheet
MT9072
LIU 1/8
Framer 1/8 RPOS RNEG EXCLi TPOS TNEG TXCL DSTo CSTo RxDLC DSTi CSTi CKi FPi DSTi0
IMA
Receive xfmr LINE 1 Transmit xfmr
RT RR
RPOS RNEG RCLK TPOS TNEG TCLK
TT TR
DSTo0
ATM BUS LIU's 2 to 7 Framers 2 to 7
DSTo CSTo 7 DSTi 1-6
LINES 2 to 7
DSTi CSTi CKi FPi 7 DSTo1-6
LIU 8/8 Receive xfmr LINE 8 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo CSTo RxDLC DSTi CSTi CKi FPi DSTi7
SSTo7
PLL From RCLK's of LIU's Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 8 of Generic LIU PLL, 1 of MT9042 ATM IMA - Framer elastic buffer is used. - LIU Transmit JA and PLL are bypassed.
PRI SEC F8o C2o C1.5o RxSYNCi RxCKi
Figure 15 - 8 T1 Links with ATM IMA with Synchronous ST-BUS Mode
SEMICMF.019
217
MT9072
Data Sheet
LIU 1/8 Receive xfmr LINE 1 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 1/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo CSTo RxDL DSTi CSTi CKi FPi PRI
PLL 1/8
F0o C2o C4o
LIU's 2 to 7
Framers 2 to 7
DSTo CSTo RxDL DSTi CSTi CKi FPi 6 6 6 6 6
PLL 2 to 7
PRI F0o C2o C4o
LINES 2 to 7
RCLK
LIU 8/8 Receive xfmr LINE 8 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo CSTo RxDL DSTi CSTi CKi FPi PRI
PLL 8/8
F0o C2o C4o
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 8 of Generic LIU PLL, 8 of MT9041 - Framer elastic buffer is optional with DSTo and CSTo. - Framer elastic buffer is not used with RxDL. - LIU Transmit JA and PLL are bypassed.
Figure 16 - 8 T1 Links with Asynchronous ST-BUS
218
SEMICMF.019
Data Sheet
17.2 E1 Applications
MT9072
LIU 1/8 Receive xfmr LINE 1 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 1/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo RxDLC RxBF DSTi CKi FPi
IMA
DSTi0 RxCK0 RxSYNC0 DSTo0 TxCK0 TxSYNC0
GCI Timing F0 C1.5i
Bits F0 = FPi = TxSYNCo F0 = RxBF = RxSYNCo C1.5 = RxDLC = RxCKo c1.5i= CKi = TxCKo
ATM BUS LIU's 2 to 7 Framers 2 to 7
DSTo RxDLC RxBF DSTi CKi FPi 6 6 6 6 6 6 DSTi 1-6 RxCK1-6 RxSYNC1-6 DSTo1-6 TxCK1-6 TxSYNC1-6
LINES 2 to 7
LIU 8/8 Receive xfmr LINE 8 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8
RPOS RNEG EXCLi TPOS TNEG TXCL DSTo RxDLC RxBF DSTi CKi FPi
DSTi7 RxCK7 RxSYNC7 DSTo7 TxCK7 TxSYNC7
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 8 of Generic LIU PLL, 1 of MT9042 IMA PLL
PRI SEC F0o C2o C4o
PLLREF0 PLLREF1
REFCK0
- Framer elastic buffer is bypassed at DSTo. - LIU Transmit JA and PLL are enabled. - Transmit and receive paths may be asynchronous with each other.
Figure 17 - 8 E1 Links with ATM IMA with Asynchronous ST-BUS Mode
SEMICMF.019
219
MT9072
LIU 1/8 Receive xfmr LINE 1 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Data Sheet
Framer 1/8
RPOS RNEG E2i TPOS TNEG T2o DSTo CSTo
HDLC Timing
F0 C2
DSTi CSTi CKi FPi
RCLK, TCLK TSP RSP 1
LIU's 2 to 7
Framers 2 to 7
DSTo CSTo 1 6
HDLC
RCLK RDATA RSP SCLK TCLK TDATA TSP
LINES 2 to 7
DSTi CSTi CKi FPi 6
LIU 8/8 Receive xfmr LINE 8 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8
RPOS RNEG E2i TPOS TNEG T2o DSTo CSTo
DSTi CSTi CKi FPi
PLL From RCLK's of LIU's
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, of Generic LIU PLL, 1 of MT9044 HDLC, 1 of PEB 20320 (MUNICH 32) - Framer elastic buffer is used. - LIU Transmit JA and PLL are bypassed. PRI SEC F0o C2o C4o C16o RCLK RSP TSP
Figure 18 - 8 E1 Links with Synchronous Common Channel Signaling for up to 24 Channels
220
SEMICMF.019
Data Sheet
MT9072
E3 LIU RPOS RNEG RCLK TPOS TNEG TCLK E3 MUX RXPOS RPOS RXNEG RNEG R34CK RCLK TXPOS TXNEG T34CK TPOS TNEG TCLK Framer 1/16 RPOS DSTo RNEG CSTo E2i TPOS TNEG T2o DSTi CSTi CKi FPi LDX STi0
Receive xfmr E3 LINE Transmit xfmr
RT RR
TT TR
STo0
Framers 2 to 15 RPOS RNEG RCLK TPOS TNEG TCLK 14 14 14 14 14 14 RPOS RNEG E2i TPOS TNEG T20 DSTo CSTo 14 STi1-14
DSTi CSTi CKi FPi
14 STo1-14
RPOS RNEG RCLK TPOS TNEG TCLK
Framer 1/16 DSTo RPOS RNEG CSTo E2i TPOS TNEG T2o DSTi CSTi CKi FPi
STi15
STo15
Notes: Framer 1-16, 2 of MT9072 LDX, 1 of MT90820 PLL, 1 of MT9042 - Framer elastic buffer is used. - LIU Transmit JA and PLL are bypassed. PLL PRI SEC F0o C2o C4o F0i C4i
From RCLK's of E3 MUX
Figure 19 - E3 (34Mb/s) MUX Cross Connect with 16 Asynchronous E1 Links
SEMICMF.019
221
MT9072
E3 LIU RPOS RNEG RCLK TPOS TNEG TCLK E3 MUX RXPOS RPOS RXNEG RNEG RCLK R34CK TXPOS TXNEG T34CK TPOS TNEG TCLK LIU 1/16 TPOS TT TNEG TR TCLK RPOS RNEG RCLK RT RR
Data Sheet
Receive xfmr E3 LINE Transmit xfmr
RT RR
Transmit xfmr LINE 1 Receive xfmr
TT TR
RPOS RNEG RCLK TPOS TNEG TCLK
14 14 14 14 14 14
LIU 2-15 TPOS TT TNEG TR TCLK RPOS RNEG RCLK RT RR
Transmit xfmr LINE 2 to 15 Receive xfmr
RPOS RNEG RCLK TPOS TNEG TCLK
LIU 16/16 TPOS TT TNEG TR TCLK RPOS RNEG RCLK RT RR
Transmit xfmr LINE 16 Receive xfmr
Notes: LIU 1-8, 8 of Generic LIU - LIU Transmit JA and PLL are not bypassed.
Figure 20 - E3 (34Mb/s) MUX Concentrator to 16 Asynchronous E1 Links
222
SEMICMF.019
Data Sheet
MT9072
LIU 1/8 RPOS RNEG RCLK TPOS TNEG TCLK Framer 1/8 RPOS DSTo RNEG E2i TxDL TxDLC TPOS TNEG T2o CKi FPi HDLC 1/8 CDSTi RxCEN CDSTo TxCEN CKi
Receive xfmr LINE 1 Transmit xfmr
RT RR
TT TR
LIU's 2 to 7
Framers 2 to 7 DSTo 6 6 6
LINES 2 to 7
TxDL TxDLC
HDLC 2 to 7 CDSTi RxCEN CDSTo TxCEN CKi
CKi FPi
Receive xfmr LINE 8 Transmit xfmr
RT RR
LIU 8/8 RPOS RNEG RCLK TPOS TNEG TCLK
TT TR
Framer 8/8 DSTo RPOS RNEG E2i TxDL TxDLC TPOS TNEG T2o CKi FPi
HDLC 8/8 CDSTi RxCEN CDSTo TxCEN CKi
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 4 of Generic LIU PLL, 1 of MT9042 HDLC, 8 of MT8952 PLL From RCLK's of LIU's PRI SEC F0o C2o C4o
- Framer elastic buffer is used. - Data Link data passes through the elastic buffer. - TxDLC outputs an enable signal - LIU Transmit JA and PLL are bypassed. - The MT8952B is in External Timing mode.
Figure 21 - 8 E1 Links with Synchronous Data Link Signaling
SEMICMF.019
223
MT9072
LIU 1/8 RPOS RNEG RCLK TPOS TNEG TCLK Framer 1/8 RPOS RxDL RNEG RxDLC E2i TxDL TxDLC TPOS TNEG T2o CKi FPi HDLC 1/16 CDSTi RxCEN CDSTo TxCEN
Data Sheet
Receive xfmr LINE 1 Transmit xfmr
RT RR
TT TR
CKi
HDLC 2/16 CDSTi RxCEN CDSTo TxCEN CKi
6 LIU's 2 to 7 Framers 2 to 7 RxDL RxDLC TxDL TxDLC 6 6 6 6 HDLC 3-15 odd CDSTi RxCEN CDSTo TxCEN CKi CKi FPi
LINES 2 to 7
RCLK
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 8 of Generic LIU PLL, 1 of MT9042 HDLC, 8 of MT8952 PLL From RCLK's of LIU's PRI SEC F0o C2o C4o
HDLC 4-16 even CDSTi RxCEN CDSTo TxCEN CKi
- Framer elastic buffer is used. - Data Link data passes through the elastic buffer. - TxDLC & RXDLC outputs an enable signal - LIU Transmit JA and PLL are bypassed. - The MT8952B is in External Timing mode.
Figure 22 - 8 E1 Links with Asynchronous Data Link Signaling
224
SEMICMF.019
Data Sheet
LIU 1/8 RPOS RNEG RCLK TPOS TNEG TCLK Framer 1/8 DSTo RPOS CSTo RNEG E2i TPOS TNEG T2o DSTi CSTi CKi FPi LDX STi0
MT9072
Receive xfmr LINE 1 Transmit xfmr TT TR RT RR
STo0
LIU's 2 to 7
Framers 2 to 7 DSTo CSTo 7 STi1-6
LINES 2 to 7 DSTi CSTi CKi FPi 7 STo1-6
Receive xfmr LINE 8 Transmit xfmr
RT RR
LIU 8/8 RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8 RPOS DSTo RNEG CSTo E2i TPOS TNEG T2o DSTi CSTi CKi FPi
STi7
TT TR
STo7
STi8-15 STo8-15
PLL Notes: Framer 1-8, 1 of MT9072 LIU 1-8, * of Generic LIU PLL, 1 of MT9042 LDX, 1 of MT90820 - Framer elastic buffer is used. - LIU Transmit JA and PLL are bypassed. From RCLK's of LIU's PRI SEC F0o C2o C4o F0i C4i
Figure 23 - 8 E1 Links with no JA or PLL in LIU, Slave or Master Mode, Jitter-Free ST-BUS
SEMICMF.019
225
MT9072
LIU 1/8 RPOS RNEG RCLK TPOS TNEG TCLK Framer 1/8 RPOS DSTo RNEG CSTo E2i TPOS TNEG T2o DSTi CSTi CKi FPi IMA DSTi0
Data Sheet
Receive xfmr LINE 1 Transmit xfmr
RT RR
TT TR
DSTo0
ATM BUS LIU's 2 to 7 Framers 2 to 7 DSTo CSTo LINES 2 to 7 DSTi CSTi CKi FPi 7 DSTo1-6 7 DSTi 1-6
Receive xfmr LINE 8 Transmit xfmr
RT RR
LIU 8/8 RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8 RPOS DSTo RNEG CSTo E2i TPOS TNEG T2o DSTi CSTi CKi FPi
DSTi7
TT TR
SSTo7
PLL From RCLK's of LIU's Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 8 of Generic LIU PLL, 1 of MT9042 IMA - Framer elastic buffer is used. - LIU Transmit JA and PLL are bypassed. PRI SEC F0o C2o C4o RxSYNCi RxCKi
Figure 24 - 8 E1 Links with ATM IMA with Synchronous ST-BUS Mode
226
SEMICMF.019
Data Sheet
MT9072
LIU 1/8 RPOS RNEG RCLK TPOS TNEG TCLK Framer 1/8 RPOS DSTo RNEG RxDLC E2i RxBF TPOS TNEG T2o DSTi CKi FPi IMA DSTi0 RxCK0 RxSYNC0 DSTo0 TxCK0 TxSYNC0 ATM BUS LIU's 2 to 7 Framers 2 to 7 DSTo RxDLC RxBF DSTi CKi FPi 6 6 6 6 6 6 DSTi 1-6 RxCK1-6 RxSYNC1-6 DSTo1-6 TxCK1-6 TxSYNC1-6 ST-BUS Timing F0 C2 C4
Receive xfmr LINE 1 Transmit xfmr
RT RR
TT TR
Bits F0 = FPi = TxSYNCo F0 = RxBF = RxSYNCo C4 = RxDLC = RxCKo C4 = CKi = TxCKo
LINES 2 to 7
Receive xfmr LINE 8 Transmit xfmr
RT RR
LIU 8/8 RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8 RPOS DSTo RNEG RxDLC E2i RxBF TPOS TNEG T2o DSTi CKi FPi
DSTi7 RxCK7 RxSYNC7 DSTo7 TxCK7 TxSYNC7
TT TR
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, 8 of Generic LIU PLL, 1 of MT9042 IMA PLL PRI SEC F0o C2o C4o
PLLREF0 PLLREF1
REFCK0
- Framer elastic buffer is bypassed at DSTo. - LIU Transmit JA and PLL are enabled. - Transmit and receive paths may be asynchronous with each other.
Figure 25 - 8 E1 Links with ATM IMA with Asynchronous ST-BUS Mode
SEMICMF.019
227
MT9072
LIU 1/8 Receive xfmr LINE 1 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Data Sheet
Framer 1/8
RPOS RNEG E2i TPOS TNEG T2o DSTo CSTo RxDL DSTi CSTi CKi FPi PRI
PLL 1/8
F0o C2o C4o
LIU's 2 to 7
Framers 2 to 7
DSTo CSTo RxDL DSTi CSTi CKi FPi 6 6 6 6 6
PLL 2 to 7
PRI F0o C2o C4o
LINES 2 to 7
RCLK
LIU 8/8 Receive xfmr LINE 8 Transmit xfmr
TT TR RT RR RPOS RNEG RCLK TPOS TNEG TCLK
Framer 8/8
RPOS RNEG E2i TPOS TNEG T2o DSTo CSTo RxDL DSTi CSTi CKi FPi PRI
PLL 8/8
F0o C2o C4o
Notes: Framer 1-8, 1 of MT9072 LIU 1-8, * of Generic LIU PLL, 8 of MT9041 - Framer elastic buffer is optional with DSTo and CSTo. - Framer elastic buffer is not used with RxDL. - LIU Transmit JA and PLL are bypassed.
Figure 26 - 8 E1 Links with Asynchronous ST-BUS
228
SEMICMF.019
Data Sheet
18.0
18.1
MT9072
AC/DC Electrical Characteristics
General
Parameter Symbol VDD VI II VO IO TST -65 -0.3 Min -0.3 -0.3 Max 5.5 VDD + 0.3 30 VDD + 0.3 30 150 Units V V mA V mA C
Absolute Maximum Ratings*
1 2 3 4 5 6 Supply Voltage Voltage at Digital Inputs Current at Digital Inputs Voltage at Digital Outputs Current at Digital Outputs Storage Temperature
* Voltages are with respect to ground (VSS) unless otherwise stated. * Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
Recommended Operating Conditions* Characteristics 1 2 Operating Temperature Supply Voltage Sym TOP VDD
Voltages are with respect to ground (VSS) unless otherwise stated
Min -40 2.7
Typ 25 3.3
Max 85 3.6
Units C V
Test Conditions
DC Electrical Characteristics - Voltages are with respect to ground (VSS) unless otherwise stated
Characteristics 1 Supply Current Sym IDD Min Typ 30 Max Units mA Test Conditions Outputs unloaded. Transmitting an all 1's signal.
2 3 4 5 6 7 8 9
Input High Voltage (Digital Inputs) Input Low Voltage (Digital Inputs) Input Leakage (Digital Inputs) Output High Voltage (Digital Outputs) Output High Current (Digital Outputs) Output Low Voltage (Digital Outputs) Output Low Current (Digital Outputs) High Impedance Leakage (Digital I/O)
VIH VIL IIL VOH IOH VOL IOL IOZ
2.0 0 1 2.4 7 VSS 2 1
VDD 0.8 10 VDD 0.4 10
V V A V mA V mA A VI = 0 to VDD IOH=7 mA @ VOH=2.4 V Source VOH=2.4 V IOL=2 mA @ VOL= 0.4 V Sink VOL=0.4 V VO = 0 to VDD
Characteristics are for clocked operation over the ranges of recommended operating temperature and supply voltage. Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing.
SEMICMF.019
229
MT9072
are with respect to ground (VSS) unless otherwise stated.
Data Sheet
Voltages
AC Electrical Characteristics - Timing Parameter Measurement Voltage Levels* Characteristics 1 2 3 Threshold Voltage Rise/Fall Threshold Voltage High Rise/Fall Threshold Voltage Low Sym VT VHM VLM Level 1.5 0.5VDD 2.0 0.7VDD 0.8 0.3VDD Units V V V V V V
Conditions/Notes TTL CMOS TTL CMOS TTL CMOS
* Timing for output signals is based on the worst case result of the combination of TTL and CMOS thresholds.
Timing Reference Points ALL SIGNALS tIRF, tORF tIRF, tORF VHM VT VLM
Figure 27 - Timing Parameter Measurement Voltage Levels
AC Electrical Characteristics - Motorola Microprocessor Timing*
Characteristics 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DS low DS High CS Setup CS Hold R/W Setup R/W Hold Address Setup Address Hold Data Delay Read Data Hold Read Data Active to High Z Delay Data Setup Write Data Hold Write Cycle Time Sym tDSL tDSH tCSS tCSH tRWS tRWH tADS tADH tDDR tDHR tDAZ tDSW tDHW tCYC 0 15
40
Min
Typ 115 50
Max
Units ns ns ns ns
Test Conditions
0 0 15
ns ns ns ns ns ns ns ns ns ns CL=150pF, RL=1k CL=150pF, RL=1k CL=150pF, RL=1k, Note 1
100 5 50 15 25 165
Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. Note 1. High impedance is measured by pulling to the appropriate rail with R L, with timing corrected to cancel time taken to discharge CL.
230
SEMICMF.019
Data Sheet
tCYC DS (RD) tDSH tCSS CS tRWS R/W (WR) tADS A0-10 tADH tRWH tCSH tDSL
MT9072
VT
VT
VT
MT9072 Inputs Address tDDR MT9072 Outputs Data tDAZ tDHR
VT
D0-15 READ
VT
tDSW
D0-15 WRITE Note: DS and CS may be connected together.
tDSH
VT
MT9072 InputsData
Figure 28 - Motorola Microprocessor Timing
AC Electrical Characteristics - Intel Microprocessor Timing*
Characteristics 1 2 3 4 5 6 7 8 9 10 11 12 13 14 RD low RD High CS Setup CS Hold WR low WR High Address Setup Address Hold Data Delay Read Data Hold Read Data Active to High Z Delay Data Setup Write Data Hold Write Cycle Time Sym tRDL tRDH tCSS tCSH tWRL tWRH tADS tADH tDDR tDHR tDAZ tDSW tDHW tCYC 0 0 70 50 15
40
Min
Typ 115 50
Max
Units ns ns ns ns ns ns ns ns ns ns ns ns ns
Test Conditions
100 5 50 15 25 165
CL=150pF, RL=1k. CL=150pF, RL=1k CL=150pF, RL=1k, Note 1
Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. Note 1. High impedance is measured by pulling to the appropriate rail with R L, with timing corrected to cancel time taken to discharge CL.
SEMICMF.019
231
MT9072
tCYC RD (DS) tRDH tCSS CS tCYC WR (R/W) tWRH A0-10 tADS tADH tCSS tADH tCSH tRDL
Data Sheet
VT
VT tWRH
VT
MT9072 Inputs Address tADS tDDR MT9072 Outputs Data tDAZ tDHR
VT
D0-15 READ
VT tDHW VT
tDSW
D0-D15 WRITE
tDSH
tDSW
MT9072 Inputs Data
Figure 29 - Intel Microprocessor Timing
AC Electrical Characteristics - JTAG Port Timing
Characteristic 1 2 3 TCK period width TCK period width LOW TCK period width HIGH TDI setup time to TCK rising TDI hold time after TCK rising TMS setup time to TCK rising TMS hold time after TCK rising TDO delay from TCK falling TRST pulse width Sym tTCLK tTCLKL tTCLKH tDISU tDIH tMSSU tMSH tDOD tTRST 25 Min 100 40 40 12 12 12 12 50 Typ Max Units ns ns ns Test Conditions BSDL spec's 12 MHz
232
SEMICMF.019
Data Sheet
tmssu tmsh
MT9072
TMS
tdih tdisu
TDI
ttclk ttclkh ttclkl
TCK
tdod
TDO
ttrst
TRST
Figure 30 - JTAG Port Timing
SEMICMF.019
233
MT9072
AC Electrical Characteristics - GCI 2.048Mb/sTiming (T1 and E1)
Characteristics 1 2 3 4 5 6 DCL Clock Width High or Low Frame Pulse Setup Frame Pulse Hold Serial Input Setup Serial Input Hold Serial Output Delay Sym tDCLW tFSCS tFSCH tSIS tSIH tSOD Min 100 50 50 30 50 125 Typ 122 Max 144 Units ns ns ns ns ns ns
Data Sheet
Test Conditions
150pF load on CSTo and DSTo
GCI Bit Cells 2Mb/s FPi (GCI FSCi) CKi (GCI DCLi) Internal (ST-BUS C2)
Timeslot 31 Bit 0
Timeslot 0 Bit 7
Timeslot 0 Bit 6
Timeslot 0 Bit 5
Figure 31 - GCI 2.048Mb/s Factional Timing Diagram
GCI Bit Cells 2Mb/s FPi (GCI FSCi)
Timeslot 31 Bit 0
Timeslot 0 Bit 7
tFSCS
tFSCH VT tDCLW tDCLW VT
CKi (GCI DCLi) tSIS CSTi & DSTi (Inputs) CSTo & DSTo (Outputs) tSIH MT9072 Inputs Data tSOD MT9072 Outputs Data MT9072 Outputs Data MT9072 Inputs Data
VT
VT
Figure 32 - GCI 2.048 Mb/s Timing Diagram
AC Electrical Characteristics - ST-BUS 2.048Mb/s Timing (T1 and E1)
Characteristics 1 2 C2i Clock Width High or Low C4i Clock Width High or Low Sym tC2W tC4W Min 222 100 Typ 244 122 Max 266 144 Units ns ns Test Conditions
234
SEMICMF.019
Data Sheet
Characteristics 3 4 6 7 8 Frame Pulse Setup Frame Pulse Hold Serial Input Setup Serial Input Hold Serial Output Delay Sym tFPS tFPH tSIS tSIH tSOD Min 50 50 30 50 90 125 Typ Max Units ns ns ns ns ns
MT9072
Test Conditions
AC Electrical Characteristics - ST-BUS 2.048Mb/s Timing (T1 and E1) (continued)
150pF load on CSTo and DSTo
ST-BUS Bit Cells 2Mb/s FPi (ST-BUS F0i) CKi (ST-BUS C4i) CKi (ST-BUS C2i)
Timeslot 31 Bit 0
Timeslot 0 Bit 7
Timeslot 0 Bit 6
Timeslot 0 Bit 5
Figure 33 - ST-BUS 2.048Mb/s Functional Timing Diagram
ST-BUS Bit Cells 2Mb/s FPi (ST-BUS F0i) CKi (ST-BUS C2i)
Timeslot 31 Bit 0 Timeslot 0 Bit 7
tFPS
tFPH VT tC2W tC2W VT
CKi (ST-BUS C4i) tSIS CSTi & DSTi (Inputs) (With C4i Clock) CSTo & DSTo (Outputs) tSIH tC4W tC4W MT9072 Inputs Data tSOD MT9072 Outputs Data MT9072 Outputs Data MT9072 Inputs Data
VT
VT
VT
Figure 34 - ST-BUS 2.048Mb/s Timing
AC Electrical Characteristics - ST-BUS 8.192Mb/s Timing (T1 and E1)
Characteristics 1 3 CKi Clock Width High or Low Frame Pulse Setup Sym tCKW tFPS Min 25 10 Typ 31 Max 35 60 Units ns ns Test Conditions
SEMICMF.019
235
MT9072
AC Electrical Characteristics - ST-BUS 8.192Mb/s Timing (T1 and E1)
Characteristics 4 6 7 8 Frame Pulse Hold Serial Input Setup Serial Input Hold Serial Output Delay Sym tFPH tSIS tSIH tSOD Min 20 10 20 55 Typ Max 60 Units ns ns ns ns
Data Sheet
Test Conditions
150pF load on CSTo and DSTo
ST-BUS Bit Cells 8Mb/s FPi (ST-BUS F16i) CKi (ST-BUS C16i)
Timeslot 127 Bit 0
Timeslot 0 Bit 7
Timeslot 0 Bit 6
Timeslot 0 Bit 5
Figure 35 - ST-BUS 8.192Mb/s Functional Timing Diagram
ST-BUS Bit Cells 8Mb/s FPi (ST-BUS F16i) CKi (ST-BUS C16i) tSIS CSTi & DSTi (Inputs) CSTo & DSTo (Outputs) tSIH MT9072 Inputs Data tSOD MT9072 Outputs Data MT9072 Outputs Data VT VT MT9072 Inputs Data
Timeslot 127 Bit 0 Timeslot 0 Bit 7
tFPS
tFPH VT tCKW tCKW VT
Figure 36 - ST-BUS 8.192Mb/s Timing
ST-BUS Bit Cells 8Mb/s FPi (ST-BUS F16i) CSTo0
Chan 0 Data Chan 1 Data Chan 2 Data Timeslot 127 Bit 0 Channel 0 Channel 1 Channel 2 Channel 3
CSTi0
Chan 0 Data
Chan 1 Data
Chan 2 Data
Note: In Cas only the lower nibble of the stream is used Note: The ABCD bits are bit 3 to bit 0 respectively
Figure 37 - ST-BUS 8.192Mb/s Functional Timing Diagram for CSTo/CSTi CAS
236
SEMICMF.019
Data Sheet
ST-BUS Bit Cells 8Mb/s FPi (ST-BUS F16i)
Timeslot 127 Bit 0 Channel 0 Channel 1 Channel 2
MT9072
Channel 3
CSTo0 CSTo0
CCS Chan 0 CCS Chan 0
CCS Chan 1 CCS Chan1
Note: In CCS the complete Byte is used in accordance with CCS Map register Y07. Any 3 CSTi/CSTo channels are used
Figure 38 - ST-BUS 8.192Mb/s Functional Timing Diagram for CSTo/CSTi CCS
18.2
T1 Mode
AC Electrical Characteristics - IMA BackplaneTiming
Characteristics 1 2 3 4 5 6 7 C1.5i Clock Width High or Low Frame Pulse Setup Frame Pulse Hold Serial Input Setup Serial Input Hold Clock output delay Serial Output Delay Sym tC1.5W tFPS tFPH tSIS tSIH tcod tSOD Min 295 50 50 30 50 50 20 90 125 Typ 324 Max 353 Units ns ns ns ns ns ns ns 150pF load on CSTo and DSTo Test Conditions
SEMICMF.019
237
MT9072
Bit Cells 1.544Mb/s FPi (Input)
Timeslot 23 Bit 0 Sbit Timeslot 0 Bit 7 Timeslot 0 Bit 6
Data Sheet
CKi ( Input)) DSTi (input)
Timeslot 23 Bit 0 Timeslot 0 Bit 7 Timeslot 0 Bit 6
Sbit
RXBF (Output)
RXDLC (Output)
DSTo (Output)
Timeslot 23 Bit 0
Sbit
Timeslot 0 Bit 7
Timeslot 0 Bit 6
Figure 39 - IMA Functional Timing Diagram
Bit Cells 1.544Mb/s FPi tC1.5W CKi (C1.5i) tSIS DSTi (Inputs) (With C1.5i Clock) EXCLi (Input) RXBF tC1.5W RXDLC (Output) DSTo (Outputs) MT9072 Outputs Data tSOD MT9072 Outputs Data tC1.5W VT VT tSIH MT9072 Inputs Data
cod Timeslot 23 Bit 0 Sbit
tfs
tfh VT tC1.5W VT
MT9072 Inputs Data
VT
VT VT
Note: In IMA Mode The Data(DSTi) is input with respect to CKI and FPi denotes the Sbit. The DSTo is output with respect to RXDLC clock and RXBF denotes the S bit. RXDLC is the delayed version of EXCLi.
Figure 40 - IMA Mode Timing Diagram
238
SEMICMF.019
Data Sheet
AC Electrical Characteristics - Transmit Multiframe Timing
Characteristics 1 2 Transmit Multiframe Setup Sym tMS Min 50 Typ Max Unit s ns
MT9072
Test Conditions
Frame N ST-BUS Bit Cells 2Mb/s or 8Mb/s FPi (ST-BUS F0i or F16i) CKi (ST-BUS C2i) CKi (ST-BUS C4i or C16i) TxMF (Input) Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5
Frame 0 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5
Figure 41 - Transmit Multiframe Functional Timing
ST-BUS Bit Cells 2Mb/s or 8Mb/s FPi (ST-BUS F0i or F16i) CKi (ST-BUS C2i) CKi (ST-BUS C4i or C16i) TxMF (Input) Note The TXMF must be aligned with the frame pulse for correct multiframe operation
Bit 0 Bit 7
VT
VT
VT tMS VT
Figure 42 - Transmit MultiframeTiming
AC Electrical Characteristics - Receive MultiframeTiming with TX8KEn Reset
Characteristics 1 Receive Multiframe Output Delay Sym tMOD Min Typ Max 55 Units ns Test Conditions 150pF load on RxMF
SEMICMF.019
239
MT9072
Frame 12 or 24 ST-BUS Bit Cells 2Mb/s or 8Mb/s FPi (ST-BUS F0i or F16i) CKi (ST-BUS C2i) CKi (ST-BUS C4i or C16i) RxMF (Output) Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Frame 0 Bit 2 Bit 1 Bit 0 Bit 7
Data Sheet
Bit 6
Bit 5
Figure 43 - Receive Multiframe Functional Timing
ST-BUS Bit Cells 2Mb/s or 8Mb/s FPi (ST-BUS F0i or F16i) CKi (ST-BUS C2i) CKi (ST-BUS C4i or C16i) RxMF (Output)
Bit 0 Bit 7
VT
VT
VT tMOD tMOD VT
Note: Tx8KEN is 0 RXMF shows the receive T1 multiframe
Figure 44 - Receive Multiframe Timing
AC Electrical Characteristics - Receive MultiframeTiming with TX8KEn Set
Characteristics 1 RXMF Output Delay Sym tTFOD Min Typ 20 Max Units ns Test Conditions 150pF
240
SEMICMF.019
Data Sheet
MT9072
TPOS/TNEG
Channel 23 Bit 7
Sbit
Channel 0 Bit 1
Channel 0 Bit 2
RxMF (Tx8KEN= 1)
TXCL
Figure 45 - Receive Multiframe Timing with TX8KEn Set Functional Timing Diagram
RXMF (Output) tTFOD TXCL (Input) tSOD TPOS/TNEG (Output)
VTT tTFOD
VTT tSOD VTT
Figure 46 - Receive Multiframe Timing with TX8KEn Set Timing Diagram
AC Electrical Characteristics - Transmit Data Link Timing
Characteristics 1 2 3 4 Clock Delay Enable Delay Data Setup Data Hold Sym tCD tED tDS tDH Min Typ 100 100 50 50 Max Units ns ns ns ns Test Conditions 150pF load on TxDLC 150pF load on TxDLC 150pF load on TxDLC 150pF load on TxDLC
SEMICMF.019
241
MT9072
1.5Mb/s Bit Cells TXCL 1.5 Mhz Clock
Data Sheet
VT
tCD TxDLC - Note 2 (Output) tED TxDLC - Note 3 (Output) tDS TxDL (Input)
tCD VT
VT tDH VT
MT9072 Inputs Data
Note 1 - TxDLC output applies for every second frame (FPi) pulse (250us) only Note 2 - Clock output provided by setting control bit DLCK=1 (register address Y06) Note 3 - Enable output provided by clearing control bit DLCK=0 (register address Y06) Note 4- TXCL is an input 1.5 Mhz clock for the PCM24 interface Note 5- The TXDLC clock is provided one frame before it is used in ESF Mode in Frames 2 4
Figure 47 - Transmit Data Link Pin Timing
AC Electrical Characteristics - Transmit Data Link Timing
Characteristics 1 2 3 4 Clock Delay Enable Delay Data Delay Read Data Hold Read Sym tCD tED tDDR tDHR Min Typ 100 100 100 50 Max Units ns ns ns ns Test Conditions 150pF load on RxDLC 150pF load on RxDLC 150pF load on RxDL 150pF load on RxDL
RXBF
RxDLC RxDL
Figure 48 - Receive Data Link Functional Diagram
242
SEMICMF.019
Data Sheet
RXDL Timeslots EXCLi tCD RxDLC - Note 2 (Output) RxDLC - Note 3 (Output) RxDL (Output) tED
MT9072
Timeslot 23 Bit 8 S bit
VT
VT
VT tDDR MT9072 Outputs Data VT
Note 1 - RxDLC output applies for every second frame (RxBF) pulse (250us) only Note 2 - Clock output provided by setting control bit DLCK=1 (register address Y06) Note 3 - Enable output provided by clearing control bit DLCK=0 (register address Y06)
Figure 49 - Receive DataLink Timing Diagram
AC Electrical Characteristics - Receive Basic Frame Pulse Pin Timing
Characteristics 1 Basic Frame Output Delay Sym tBD Min Typ 100 Max Units ns Test Conditions 150pF load on RxBF
RXDL Bit Cells EXCLi
Timeslot23 Bit 8
S Bit
VT tBD
RxBF (Output)
VT
Figure 50 - Receive Basic Frame Pulse Pin Timing
AC Electrical Characteristics - PCM24 Transmit Timing
Characteristics 1 2 3 Transmit Delay Transmit Delay in RZ mode Transmit Invalid in RZ Mode Sym tTD
tr TD tr DI
Min
Typ 50 200 200
Max
Units ns ns ns
Test Conditions 150pF load on TPOS and TNEG 150pF load on TPOS and TNEG 150pF load on TPOS and TNEG
SEMICMF.019
243
MT9072
PCM 24 Transmit Bit Cells 1.544 Mb/s TXCL (1.544 MHz Clock)
Data Sheet
VT
3.088 MHz Clock
TPOS or TNEG (Output) (NRZ,Clke =0)
tTD
MT9072 Outputs Data trDI MT9072 Outputs Data
VT
trTD TPOS or TNEG (Output) (RZ,Clke=0)
VT
Note 1 in RZ Mode the data has to sampled on the falling edge of 1.544 MHz clock by an external device. Note 2 The 3.088 MHz clock is internal and is shown just for reference
Figure 51 - PCM 24 Transmit Timing
244
SEMICMF.019
Data Sheet
PCM24Transmit Bit Cells (2Mb/s) (Sample Data) TXCL (1.544 MHz Transmit Clock Input,clke=0) TXCL (1.544 MHz Transmit Clock Input,clke=1 Only valid in NRZ TPOS (Output) (RZ Dual Rail) TNEG (Output) (RZ Dual Rail) TPOS (Output) (RZ Single Rail) TNEG (Output) (RZ Single Rail) TPOS (Output) (NRZ Dual Rail)
MT9072
(1) (0) (1) (1)
TNEG (Output) (NRZ Dual Rail) TPOS (Output) (NRZ Single Rail)
TNEG (Output) (NRZ Dual Rail)
Note: CLKE =1 is only valid in NRZ Mode
Figure 52 - PCM24 Transmit Functional Timing
AC Electrical Characteristics - PCM24 Receive Timing
Characteristics 1 2 Receive Setup Receive Hold Sym tRS tRH Min Typ 50 50 Max Units ns ns Test Conditions
SEMICMF.019
245
MT9072
PCM24 Receive Bit Cells(Neg Edge) (Sample Data) EXCLi 1.5 Meg Clock CLKE=1 EXCLi 1.5 Meg Clock CLKE=0 RPOS (Input) (RZ Dual Rail) RNEG (Input) (RZ Dual Rail) RPOS (Input) (NRZ Dual Rail) RNEG (Input) (NRZ Dual Rail) RPOS (Input) (NRZ Single Rail) RNEG (Input) (NRZ Single Rail)
Data Sheet
(1)
(0)
(1)
(1)
Figure 53 - PCM24 Receive Functional Timing
PCM 24 Receive Bit Cells 1.544 Mb/s EXCLi tRS RPOS or RNEG (Input) (RZ or NRZ Pos Edge CLKE=0 EXCLi tRS RPOS or RNEG (Input) (RZ or NRZ Neg Edge CLKE=1) tRH tRH VT VT
MT9072 Inputs Data
VT
MT9072 Inputs Data
Figure 54 - PCM24 Receive Timing
246
SEMICMF.019
Data Sheet
18.2.1 AC Electrical Characteristics - PCM24 and ST-BUS Frame Format
In both the transmit and receive directions, PCM24 LSB maps to ST-BUS LSB.
2.0 ms
FRAME FRAME
MT9072
15
0
********
FRAME 14
FRAME 15
FRAME 0
timeslot
timeslot
0
1
****
125 s
timeslot
timeslot
30
31
Most Significant Bit (First)
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
BIT 8
Least Significant Bit (Last)
(8/2.048) s
Figure 55 - PCM 24 Format
125s
CHANNEL 31 or 127 CHANNEL 0
***
CHANNEL 30 or 126
CHANNEL 31 or 127
CHANNEL 0
Most Significant Bit (First)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Least Significant Bit (Last)
(8/2.048 or 8/8.192)s
Figure 56 - ST-BUS Format
Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. Note 1. High impedance is measured by pulling to the appropriate rail with R L, with timing corrected to cancel time taken to discharge CL.
18.3
E1 Mode
AC Electrical Characteristics - Receive IMA Timing
Characteristics 1 2 4 RXDLC Clock Width High or Low Receive Basic Frame Pulse Delay RXDLC Clock Delay Sym tE4W tFD tCD Min 25 50 50 125 Typ Max 100 Units ns ns ns 150pF load on CSTo and DSTo Test Conditions
SEMICMF.019
247
MT9072
PCM30 Receive Timeslots EXcli Input
TFD
Data Sheet
Timeslot 31 Bit 0
Timeslot 0 Bit 7
VT VT tE4HW tE4LW tCD VT tSOD
RXBF Output
Rxdlc Output
DSTo (Outputs)
MT9072 Outputs Data
MT9072 Outputs Data
VT
Note that the Transmit IMA mode uses Fpi Cki and DSTi and timing is indentical to the 2Mb/s ST-BUS (See Figure 33)
Figure 57 - Receive IMA Timing
ST-BUS Bit Cells 2Mb/s RXBF
Timeslot 31 Bit 0
Timeslot 0 Bit 7
Timeslot 0 Bit 6
Timeslot 0 Bit 5
RXDLC
E2i
Figure 58 - Receive IMA Functional Timing Diagram
AC Electrical Characteristics - Transmit Multiframe (CRC-4 or CAS) Timing
Characteristics 1 Transmit Multiframe Setup Sym tMS Min 50 Typ Max Units ns Test Conditions
248
SEMICMF.019
Data Sheet
MT9072
Bit 7 Timeslot 0 Frame 0
ST-BUS Bit Cells 2Mb/s or 8Mb/s FPi (ST-BUS F0i or F16i) CKi (ST-BUS C4i or C16i) TxMF (Input)
Frame N
VT
VT tMS VT
Figure 59 - Transmit Multiframe (CRC-4 or CAS) Timing
Frame N ST-BUS Bit Cells 2Mb/s or 8Mb/s FPi (ST-BUS F0i or F16i) Internal (ST-BUS C2) CKi (ST-BUS C4i or C16i) TxMF (Input)
Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5
Frame 0
Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5
Figure 60 - Transmit Multiframe (CRC-4 or CAS) Functional Timing
AC Electrical Characteristics - Receive Multiframe (CRC-4 or CAS) Timing
Characteristics 1 Receive Multiframe Output Delay Sym rMOD Min Typ Max 55 Units ns Test Conditions 150pF load on RxMF
SEMICMF.019
249
MT9072
ST-BUS Bit Cells 2Mb/s ST-BUS Bit Cells 8Mb/s FPi (ST-BUS F16i) 8Mb/s CKi (ST-BUS C16i) 8Mb/s FPi (ST-BUS F0i) 2Mb/s CKi (ST-BUS C4i) 2Mb/s RxMF (Output)
Bit 0 Bit 7
Data Sheet
Bit 0
Bit 7
VT
VT
VT
VT rMOD rMOD VT
Figure 61 - Receive Multiframe (CRC-4 or CAS) Timing
Frame 15 ST-BUS Bit Cells 2Mb/s or 8Mb/s FPi (ST-BUS F0i or F16i) Internal (ST-BUS C2 or C8) CKi (ST-BUS C4i or C16i) RxMF (Output)
Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5
Frame 0
Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5
Figure 62 - Receive Multiframe (CRC-4 or CAS) Functional Timing
AC Electrical Characteristics - Receive MultiframeTiming with TX8KEn Set
Characteristics 1 RXMF Output Delay Sym tTFOD Min Typ 20 Max Units ns Test Conditions 150pF
250
SEMICMF.019
Data Sheet
MT9072
RXMF (Output) tTFOD T2o (Output) tSOD TPOS/TNEG (Output)
VTT tTFOD
VTT tSOD VTT
Figure 63 - Receive Multiframe Timing with TX8KEn Set
TPOS/TNEG
Channel 31 Bit 8
Channel 0 Bit 1
Channel 0 Bit 2
Channel 0 Bit3
RxMF
(Tx8KEN= 1)
T2O
Figure 64 - Receive Multiframe Timing with TX8KEn Set
AC Electrical Characteristics - Transmit Data Link Pin Timing
Characteristics 1 2 3 4 Clock Delay Enable Delay Data Setup Data Hold Sym tCD tED tDS tDH 100 50 Min Typ Max 55 55 Units ns ns ns ns Test Conditions 150pF load on TxDLC 150pF load on TxDLC
SEMICMF.019
251
MT9072
ST-BUS Bit Cells 2Mb/s ST-BUS Bit Cells 8Mb/s CKi (ST-BUS C16i) 8Mb/s CKi (ST-BUS C4i) 2Mb/s TxDLC - Note 2 (Output) tED TxDLC - Note 3 (Output) tDS TxDL (Input) Note 1 - TxDLC output applies for every second frame (FPi) pulse (250us) only Note 2 - Clock output provided by setting control bit DLCK=1 (register address Y08) Note 3 - Enable output provided by clearing control bit DLCK=0 (register address Y08) tDH MT9072 Inputs Data tED
Data Sheet
VT
VT tCD tCD VT
VT
VT
Figure 65 - Transmit Data Link Pin Timing
252
SEMICMF.019
Data Sheet
Timeslot 31 ST-BUS Bit Cells 2Mb/s
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6
MT9072
Timeslot 0
Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7
Timeslot 1
Bit 6 Bit 5 Bit 4
TS124 ST-BUS Bit Cells 8Mb/s FPi (ST-BUS F0i) Internal (ST-BUS C2) CKi (ST-BUS C4i) FPi (ST-BUS F16i) CKi (ST-BUS C16i) TxDLC - Note 2 (Output) TxDLC - Note 3 (Output) TxDL (Input) (2Mb/s) TxDLC - Note 2 (Output) TxDLC - Note 3 (Output)
TS125
TS126
TS127
TS0
TS1
TS2
TS3
TS4
TS5
Bit Bit Bit Bit Bit Bit Bit Bit Bit Bit 76543210 76543210 76543210 76543210 76543210 76543210 76543210 76543210 76543210 76543210
Example A - 20 kbit/s clock output Sa4 to Sa8 clocked in by MT9072 Example A - enable output Sa4 to Sa8 clocked in by MT9072
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit Bit Bit Bit Bit Sa4 Sa5 Sa6 Sa7 Sa8 Bit 7 Bit 6 Bit 5 Bit 4
Example B - 12 kbit/s clock output Sa4, Sa7 and Sa8 clocked in by MT9072 Example B - enable output Sa4, Sa7 and Sa8 clocked in by MT9072
Note 1 - TxDLC output applies for every second frame (FPi) pulse (250us) only Note 2 - Clock output provided by setting control bit DLCK=1 (register address Y08) Note 3 - Enable output provided by clearing control bit DLCK=0 (register address Y08)
Figure 66 - Transmit Data Link Pin Functional Timing
AC Electrical Characteristics - Receive Basic Frame and E4o Timing
Characteristics 1 2 3 Basic Frame Output Delay Clock Delay E4o Clock High Width Sym tBD tCD tE4HW 50 Min 30 Typ Max 115 55 200 Units ns ns ns Test Conditions 150pF load on RxBF 150pF load on RxDLC 150pF load on RxDLC
SEMICMF.019
253
MT9072
AC Electrical Characteristics - Receive Basic Frame and E4o Timing
Characteristics 3 E4o Clock Low Width
RXDL PCM 30 Bit Cells E2i Input tE4HW E4o - Note 1 (RxDLC Pin) Output RxBF (Output) tE4LW tCD tCD
Data Sheet
Sym tE4LW
Timeslot 31 Bit 8
Min 25
Typ
Max 75
Units ns
Test Conditions 150pF load on RxDLC
Timeslot 0 Bit 1
VT
VT tBD
t BD
VT
Note 1 - The E4o signal is output at the RxDLC Pin when the E4CK control bit (address Y08) is set to one. Note 2 - The PCM Timeslots are referred to RXDL Output which is delayed 4 bits from the RPOS/RNEG input. Note3- The E4o Clock(RXDLC Output) is not a 50% duty cycle clock, it will be low for 25 % and high for 75% of the 4.096 MHz clock
Figure 67 - Receive Basic Frame and E4o Timing
AC Electrical Characteristics - Receive Data Link Timing
Characteristics 1 2 3 Clock Delay Enable Delay Data Delay Read Sym tCD tED tDDR Min Typ Max 55 55 125 Units ns ns ns Test Conditions 150pF load on RxDLC 150pF load on RxDLC 150pF load on RxDL
RXDL Bit Cells E2i tCD RxDLC - Note 2 (Output) tED RxDLC - Note 3 (Output) tDDR RxDL (Output) Note Note Note Note 1 2 3 4 MT9072 Outputs Data RxDLC output applies for every second frame (RxBF) pulse (250us) only Clock output provided by setting control bit DLCK=1 (register address Y08) Enable output provided by clearing control bit DLCK=0 (register address Y08) The PCM 30 Timeslots are with respect to RXDL Output VT tED VT tCD VT
VT
Figure 68 - Receive Data Link Timing
254
SEMICMF.019
Data Sheet
Timeslot 31 RXDL PCM 30 Bit Cells E2i
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6
MT9072
Timeslot 0
Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7
Timeslot 1
Bit 6 Bit 5 Bit 4
RxBF (Output) RxDLC - Note 2 (Output) RxDLC - Note 3 (Output) RxDL (Output) RxDLC - Note 2 (Output) RxDLC - Note 3 (Output) Note Note Note Note 1 2 3 4 -
Example A - 20 kbit/s clock output Sa4 to Sa8 clocked in by External Device Example A - enable output Sa4 to Sa8 clocked in by External Device
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit Bit Bit Bit Bit Sa4 Sa5 Sa6 Sa7 Sa8 Bit 7 Bit 6 Bit 5 Bit 4
Example B - 12 kbit/s clock output Sa4, Sa7 and Sa8 clocked in by External Device Example B - enable output Sa4, Sa7 and Sa8 clocked in by External Device
RxDLC output applies for every second frame (RxBF) pulse (250us) only Clock output provided by setting control bit DLCK=1 (register address Y08) Enable output provided by clearing control bit DLCK=0 (register address Y08) PCM Timeslot is with reference to RXDL Output. It is delayed 4 bits from RPOS/RNEG
Figure 69 - Receive Data Link Pin Functional Timing
AC Electrical Characteristics - PCM30 Transmit Timing
Characteristics 1 2 Transmit Output Clock Delay Transmit Output Delay Sym tCD tTOD Min Typ Max 55 55 Units ns ns Test Conditions 150pF load on T2o 150pF load on TPOS and TNEG
SEMICMF.019
255
MT9072
PCM 30 Transmit Bit Cells 2Mb/s T2o (Output) T2OP=0 T2o (Output) T2OP=1 CKi (ST-BUS C4i) CKi (ST-BUS C16i) tTOD TPOS or TNEG (Output) (NRZ) TPOS or TNEG (Output) (RZ) Note that the times specified apply to non-loopback modes MT9072 Outputs Data tTOD MT9072 Outputs Data tCD
Data Sheet
tCD VT
VT
VT
VT
VT
VT
Figure 70 - PCM 30 Transmit Timing
256
SEMICMF.019
Data Sheet
PCM30 Transmit Bit Cells (2Mb/s) (Sample Data) T2o (Output) T2OP=0 T2o (Output) T2OP=1 CKi (ST-BUS C4i) CKi (ST-BUS C16i) TPOS (Output) (RZ Dual Rail) TNEG (Output) (RZ Dual Rail) TPOS (Output) (NRZ Dual Rail) TNEG (Output) (NRZ Dual Rail) TPOS (Output) (NRZ Single Rail) TNEG (Output) (NRZ Single Rail) Note: T2o is only applicable in the NRZ mode
MT9072
(1) (0) (1) (1)
Figure 71 - PCM30 Transmit Functional Timing
AC Electrical Characteristics - PCM30 Receive Timing
Characteristics 1 2 Receive Setup Receive Hold Sym tRS tRH Min 50 50 Typ Max Units ns ns Test Conditions
SEMICMF.019
257
MT9072
PCM 30 Receive Bit Cells 2Mb/s E2i tRS RPOS or RNEG (Input) (RZ or NRZ) tRH
Data Sheet
VT
MT9072 Inputs Data
VT
Figure 72 - PCM 30 Receive Timing
PCM30 Receive Bit Cells(Neg Edge) (Sample Data) E2i 2 Meg Clock CLKE=1 E2i 2 Meg Clock CLKE=0 RPOS (Input) (RZ Dual Rail) RNEG (Input) (RZ Dual Rail) RPOS (Input) (NRZ Dual Rail) RNEG (Input) (NRZ Dual Rail) RPOS (Input) (NRZ Single Rail) RNEG (Input) (NRZ Single Rail)
(1)
(0)
(1)
(1)
ClKE selection is noly applicable for NRZ mode
Figure 73 - PCM30 Receive Functional Timing
258
SEMICMF.019
Data Sheet
18.4 AC Electrical Characteristics - PCM30 and ST-BUS Frame Format
MT9072
In both the transmit and receive directions, PCM30 LSB maps to ST-BUS LSB.
2.0 ms FRAME 15 FRAME 0
********
FRAME 14
FRAME 15
FRAME 0
TIMESLOT 0
TIMESLOT 1
****
125 s
TIMESLOT 30
TIMESLOT 31
Most Significant Bit (First)
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
BIT 8
Least Significant Bit (Last)
(8/2.048) s
Figure 74 - PCM 30 Format
125s CHANNEL 31 or 127 CHANNEL 0
***
CHANNEL 30 or 126
CHANNEL 31 or 127
CHANNEL 0
Most Significant Bit (First)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Least Significant Bit (Last)
(8/2.048 or 8/8.192)s
Figure 75 - ST-BUS Format
19.0
Applicable Specifications
Standard Title Digital Heirarchy_Electrical Interfaces Layer 1 In-Service Digital Transmission Performance Monitoring Network to Customer Installation Metallic Interfaces ISDN Primary Rate- Customer Installation Metallic Interfaces Accunet T1.5 Service Description and Interface Specification Digital Data Systems(DDS)- T1 Digital Multiplexor(T1DM) Requirements Pulse Code Modulation(PCM) of Voice Frequencies Table 204 - Applicable Telecommunications Specifications.
T1.102-1993 T1.231-1993 T1.403-1995 T1.408-1990 TR 62411-1990 TA-TSY-000278 Issue1, 1985 G.711
SEMICMF.019
259
MT9072
Data Sheet
Packaging
260
SEMICMF.019
c Zarlink Semiconductor 2002 All rights reserved.
Package Code Previous package codes:
ISSUE ACN DATE APPRD.
For more information about all Zarlink products visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request.
Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2002, Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE

▲Up To Search▲

Price & Availability of MT9072

	To Download MT9072 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .